Elko ELAN-RF-003 Manuel utilisateur

1/25

Converter Ethernet to RF signal

eLAN-RF-003 Introduction:

Installation Manual

02-040/2012

Instruction Manual for the

eLAN-RF-003

2/25

Converter Ethernet to RF signal

eLAN-RF-003 Introduction:

Installation Manual

02-040/2012

Contents

1.Introduction:................................................................................................................................3

2.Main characteristics:....................................................................................................................3

3.Technical parameters: .................................................................................................................4

4.Hardware installation: .................................................................................................................5

4.1Front panel: ...........................................................................................................................5

4.2Rear panel: ............................................................................................................................5

4.3System requirements:...........................................................................................................6

4.4Requirements for installation environment:........................................................................6

4.5Examples of use: ...................................................................................................................6

5.Configuration of computer: ........................................................................................................8

6.Configuring the iMM Client:......................................................................................................11

7.Configuration of the eLAN-RF-003:...........................................................................................12

8.Configuring the eLAN-RF-003 using the SW eLAN-RF-003 Configurator:...............................12

8.1Administrator login:............................................................................................................13

8.2LAN parameters: .................................................................................................................13

8.3About the device:................................................................................................................13

8.4Buttons: ...............................................................................................................................13

8.5Device settings:...................................................................................................................14

8.5.1Basic settings. ..............................................................................................................14

8.5.2RF Repeater..................................................................................................................14

8.5.3RF Router .....................................................................................................................16

8.5.4List of addresses:..........................................................................................................18

8.5.5User panel: ...................................................................................................................19

9.Configuring the eLAN-RF-003:..................................................................................................20

9.1Settings tab: ........................................................................................................................21

9.2Tab Firmware: ......................................................................................................................22

9.3Tab Builder: .........................................................................................................................23

9.4Tab Panel: ............................................................................................................................24

9.5Tab log out: .........................................................................................................................24

10.Troubleshooting: ....................................................................................................................25

3/25

Converter Ethernet to RF signal

eLAN-RF-003 Introduction:

Installation Manual

02-040/2012

1. Introduction:

Congratulations on purchasing the eLAN-RF-003 control unit, an element of the RF Control wireless system.

Before you begin

The instruction manual provides information on installing and operating the device. The instruction manual is

always a part of the supply. Only perform installation after becoming thoroughly familiar with this User Guide

and device functions.Problem-free function of the device also depends on the way it was shipped, stored and

handled. If you notice any signs of damage, deformation, malfunction or a missing part, do not install this product

and return it to the point of sale. At the end of its service life, the product and its parts must be treated as electronic

waste. Before starting the installation, make sure that all wires and connected parts are not under voltage. When

assembling and performing maintenance, you must uphold safety regulations, standards, directives and special

provisions for working with electrical equipment.

2. Main characteristics:

The eLAN-RF-003 converter converts commands from the LAN TCP/IP network to an RF signal for

controlling RF actuators.

It enables bidirectional communication between the RF INELS and Ethernet systems.

It can be used to extend the range of the RF signal via UTP cable (Ethernet network) or WiFi (between

individual floors in the house).

Option of control and reading values from RF actuators (temperature, ON/OFF status) - in the iMM

environment.

Configuration and management of ELAN-RF-003 is performed via:

1) iMM server

2) its own web server

3) configuration SW eLAN-RF-003 Configurator

For access to eLAN-RF-003 from the Internet, you must connect the eLAN-RF-003 to a Public IP address.

The device is compliant with standards 802.3/802.3u (Fast Ethernet)

The device is compliant with standards ISO 802.3/ IEEE 802.3u ( 10BASE-T)

Automatic cable crossing detection of Ethernet cable - MDIX

10/100BaseT Ethernet, auto-detection

Option of powering by PoE – maximum voltage 27V / 200mA max. consumption.

Support for administration and configuration via web interface.

Supports firmware updates via a web interface.

It has its own web server

Aluminum design box in desktop style.

4/25

Converter Ethernet to RF signal

eLAN-RF-003 Technical parameters:

Installation Manual

02-040/2012

3. Technical parameters:

Interface RF Control

Communications protocol: Oasis & RF Touch Compatible

Transmitting frequency: 868 MHz

Signal transmission method bidirectionally addressed message

Output for antenna: SMA Connector

Indication of RF communication: 1 x red RF Status LED

Antenna: 1 dB (part of supply)

Range in open areas: up to 100m

Ethernet Communication

Operating status indication ETH: green LED

Communication indication ETH: yellow LED

Communications interface: 10/100 Mbps (RJ45)

Preset IP address: 192.168.1.1

Supply voltage / jm. Current: 10-27 V DC / 200 mA (safe low voltage)

Power supply PoE Max. 27V / 200mA max. consumption

Connection: connector Jack Ø 2.1 mm

Supply voltage indication: green LED

Other

Other powering options: connector USB-B

USB activity indication: yellow USB Status LED

Button RESET: restart product / reset product to factory settings

Power source: 230 VAC / 12 V DC part of supply

Working temperature: -20 .. +55 °C

Storage temperature: -25 .. +70 °C

Protection class: IP 20

Pollution degree: 2

Working position: any

Installation: free

Design: design box

Dimensions: 90 x 52 x 65 mm

Weight: 136 g

Factory settings:

Password: elkoep

IP address: 192.168.1.1

5/25

Converter Ethernet to RF signal

eLAN-RF-003 Hardware installation:

Installation Manual

02-040/2012

4. Hardware installation:

4.1 Front panel:

Power connector DC 12V – Input for connecting supplied power adapter.

Plug USB B – Used for servicing, (or can be used to power the product).

Green POWER LED power supply indicator.

Yellow USB Status LED – displays activity at the USB port.

Button RESET – used to restart or restore the product to factory settings*.

Connector Ethernet RJ 45 – used to connect mainly to the local network (LAN) or PC.

Yellow LED on Ethernet connector - indicates operating status.

Green LED diode on Ethernet connector - indicates communication.

*By shortly pressing (around 1s) the RESET button in the status where the product is connected to the supply

voltage, the product will restart. This restart neither changes nor deletes settings.

RESET to factory settings occurs after pressing and holding the RESET for min. 10s. This restart returns the product to

its factory settings, i.e. the IP adress is set to 192.168.1.1, the user name and password are set at: admin /

elkoep, user / elkoep, all learning and assigned IR codes and

the created web server control panel are erased.

4.2 Rear panel:

Red RF STATUS LED – Displays RF communication – during transmission the RF signal LED diode flashes.

SMA antenna connector – pro connecting the RF antenna.

Power connector

10-27V/200mA

Yellow USB status LED

LED indicator of Ethernet

communication

Ethernet connector (RJ 45)

RESET button

Green POWER LED power supply indicator

USB B connector

Red LED RF STATUS SMA antenna connector

6/25

Converter Ethernet to RF signal

eLAN-RF-003 Hardware installation:

Installation Manual

02-040/2012

4.3 System requirements:

Functioning iMM Client or PC with functioning Ethernet adapter.

For PCs, installed web browser (such as Mozilla Firefox,Opera, etc.).

You must have installed .NET Framework 3.5 and higher.

Connecting Ethernet cable with RJ45 connectors.

4.4 Requirements for installation environment:

The product cannot be placed where it is exposed to moisture or excessive heat.

Place the eLAN-RF-003 at a location where it can be connected to the Ethernet network, power source and

its RF antenna will be in sufficient distance from the controlled device.

For fault-free communication, adhere to the principles of installing the RF device, see RF catalog.

4.5 Examples of use:

Connect the power supply using the supplied adapter.

Connect the eLAN-RF-003 device to the Ethernet by a cable to the computer, iMM Client, eLAN-RF-003 or

Ethernet hub.(The cable must have an RJ45 connector, the device has an automatic cable crossover

detection function - so cable crossover does not present a problem).

Example 1:

The example of use of two eLAN-RF-003 devices in connection with the WiFi network is advantageous when this

network is already in use, and is only augmented with the eLAN-RF-003 device. The eLAN-RF-003 device can

function if the WiFi routers are connected to a bridge and both eLAN-RF-003 devices can "see" each other. For this

case, it is necessary to set the eLAN-RF-003 to the routing function.

7/25

Converter Ethernet to RF signal

eLAN-RF-003 Hardware installation:

Installation Manual

02-040/2012

Example 2:

Basic use where the RF controller (RF Touch, RF Pilot, RFRF AP/USB, RF Key) cannot control the RF actuators, due to

great distance, and when it is not possible to use the RFRP-20 repeater. By simply connecting to the network or by

extending an Ethernet cable, you can extend the maximum range (distance) of RF controllers.

For this case, it is necessary to set the eLAN-RF-003 to the routing function.

Example 3:

The next example illustrates the case where you already own an iMM Client server and you want to control all the

RF actuators and maintain an overview on statuses of all RF actuators found within the range of the eLAN-RF-003.

8/25

Converter Ethernet to RF signal

eLAN-RF-003 Configuration of computer:

Installation Manual

02-040/2012

Example 4:

This example is similar to the previous one, except the device works via the PC. Thanks to the web server, it is easy to

control the RF actuators.

5. Configuration of computer:

For logging in to the web server or changing the IP address (192.168.1.1).

Example of configuration in the Windows system, proceed according to the following instructions:

1. In the computer Start menu, open the Control panel and select Network connections.

9/25

Converter Ethernet to RF signal

eLAN-RF-003 Configuration of computer:

Installation Manual

02-040/2012

2. In the window Network connections right-click on LAN (connecting to local area network), then right-

click on Properties.

3. After opening the window: Connection to local network in the main dialog window, select "Protocol

Internet network (TCP/IP)". After choosing this type of protocol by clicking on Properties, another

configuration window opens.

10/25

Converter Ethernet to RF signal

eLAN-RF-003 Configuration of computer:

Installation Manual

02-040/2012

4. Perform configuration by choosing the tab Use the following IP address:

Enter the following settings into the text field:

IP Address: Set the IP address of your computer in dotted decimal notation, ex. 192.168.1.2 (where 2 is any value

from 2 to 255).

Subnet Mask: Address code that determines the size of the network. The value 255.255.255.0 is commonly used for

the subnet mask.

Default Gateway: Here enter the address of the product IP eLAN-RF-003 in dotted decimal format separated by

periods (default setting: 192.168.1.1).

The address of the DNS server need not be entered.

5. Save the settings by confirming - click OK

Autres manuels pour eLAN-RF-003

Table des matières

Autres manuels Elko Convertisseur de média

Elko

Elko iNELS RFTM-1 Manuel utilisateur

Elko

Elko Inels RFSG-1M Manuel utilisateur

Elko

Elko inels RFSG-1M Manuel utilisateur

Elko

Elko RFIM-20B Manuel utilisateur

Elko

Elko inels RFSG-1M Manuel utilisateur

Elko

Elko RFIM-20B Manuel utilisateur

Elko

Elko RFIM-20B Manuel utilisateur

Elko

Elko iNels RFTM-1 Manuel utilisateur

Elko

Elko iNELS RFSG-1M Manuel utilisateur

Elko

Elko RFIM-20B Manuel utilisateur

Elko

Elko 7180 Manuel utilisateur

Elko

Elko inelsAir AirTM-100NB Manuel utilisateur

Elko

Elko iNELS RFSG-1M Manuel utilisateur

Elko

Elko eLAN-IR-003 Manuel utilisateur

Elko

Elko RFSG-1M Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur

Elko eLAN-RF-003 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques