1 / 5
AirSLC-100NB/NEMA
02-38/2019 Rev.: 0
6
7
4
8
3
59
1
2
3 4
1
2
ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
www.elkoep.com
Characteristics
Description
EN
General instrucions
Made in Czech Republic
Street light controller - NEMA socket
Cloud app assignment
It is done in your Smartphone application. Enter the relevant information on the product
cover into the application.
Function
1. Cover
2. Base
3. 0(1)-10 V (+) / DALI (+) *
4. L - phase (LINE)
5. Not connected
6. 0(1)-10 V (-) / DALI (-) *
7. N - neutral (NEUT)
8. V - switched output (LOAD)
9. Not connected
* by module type (analog / DALI)
Underside view
• Used for remote control of the luminaire: ON / OFF / DIMM.
•
Measures current ow - fault detection (ballast fault, light source, connecting
wires ...)
• Communicates over the wireless LPWAN network (NB-IoT).
• Output signal 0 (1) -10V or DALI for direct control of ballast in luminaire.
• Internal digital light intensity sensor, range 5 - 100,000Lx.
• Internal digital temperature sensor in the range -30 ... 70 ° C.
• Power supply: 100-230 V AC, Power 3.5 VA.
• The IP66, UV-resistant, is designed for outdoor mounting in the NEMA socket.
• Update using the RFAF / USB Service Key.
• Connection standard: Standard ANSI C136.41 Dimming Receptacle.
Internet of Things (IoT)
• The IOT wireless communications category describes the Low Power Wide Area
(LPWA). This technology is designed to provide full-range coverage both inside and
outside buildings, energy-saving and low-cost operation of individual devices. The
NarrowBand network is available to use this standard.
Information about the NarrowBand network
• The network provides two-way communication and the only one to use the licensed
LTE band. Our devices allow band 1 (2100MHz), Band 3 (1800MHz), Band 8 (900MHz),
Band 5 (850MHz), Band 20 (800MHz) and Band 28 (700MHz).
• It uses this SIM card technology for each device.
• The advantage of NarrowBand is the use of already built-up grids, which ensures suf-
cient reception outside and inside buildings.
• For more information on this technology, please visit www.vodafone.cz
Caution for proper operation:
• Products are installed according to the wiring diagram given for each product.
• For proper device functionality, it is necessary to have sucient coverage of the se-
lected network at the installation site.
• At the same time, the device must be registered in the network. Successful device reg-
istration on a given network requires a charge for trac.
• Each network oers dierent tari options - it always depends on the number of mes-
sages you want to send from your device. Information on these taris can be found in
the current version of the ELKO EP pricelist.
When the power is connected, the device sends the initial message containing the meas-
ured temperature and light intensity.
Sensor senses temperature and intensity of lighting every 2 minutes. After that, it sends a
data message of measured values every 15 minutes.
Function setting (message from server):
• Function AUTOMAT:
- the on / o is controlled according to the intensity measured by the light sensor
• Function SEMI-AUTOMAT:
- Switching on / off, the brightness is set according to the set schedule (the schedule
can be set by a message from the server)
- Outside the schedule is set to Auto
• Function MANUAL:
- Messages from the server can be turned on / off, adjust brightness and interval for
sending data messages.
