Elenco Electronics M-1150K Guide de l'utilisateur

ANALOG MULTIMETER

MODEL M-1150K

Assembly and Instruct on Manual

Elenco Electron cs, Inc.

PARTS LIST

RESISTORS

QTY SYMBOL VALUE COLOR CODE PART #

r1R26 .25ΩShunt Wire 1 269

r1 R12 .96Ω1% 1/2W black-white-blue-silver-brown 1 9631

r1R11 1Ω1% 1/4W brown-black-black-gold-brown 121 3

r1 R2 18.5Ω1% 1/4W brown-gray-green-gold-brown 121832

r1R1 12Ω1% 1/4W brown-black-red-black-brown 131 34

r1R21 2Ω1% 1/4W red-black-black-black-brown 132 3

r1 R2 24 Ω1% 1/4W red-yellow-black-black-brown 13243

r1R18 2KΩ1% 1/4W red-black-black-brown-brown 142 3

r1R9 3KΩ1% 1/4W orange-black-black-brown-brown 143 33

r1R3 5KΩ1% 1/4W green-black-black-brown-brown 145 3

r1 R24 18KΩ1% 1/4W brown-gray-black-red-brown 15183

r1 R17 31KΩ1% 1/4W orange-brown-black-red-brown 15313

r1 R22 34KΩ1% 1/4W orange-yellow-black-red-brown 15343

r1R4 4KΩ1% 1/4W yellow-black-black-red-brown 154 3

r1 R19 44KΩ1% 1/4W yellow-yellow-black-red-brown 15443

r1 R13 83.3KΩ1% 1/4W gray-orange-orange-red-brown 15833

r1 R5 15 KΩ1% 1/4W brown-green-black-orange-brown 161533

r1 R23 195KΩ1% 1/4W brown-white-green-orange-brown 16193

r1 R14 36 KΩ1% 1/4W orange-blue-black-orange-brown 16363

r1R6 8KΩ1% 1/4W gray-black-black-orange-brown 168 3

r1 R15 1.8MΩ1% 1/2W brown-gray-black-yellow-brown 171831

r1R7 4MΩ1% 1/2W yellow-black-black-yellow-brown 174 31

r1 R16 6.75MΩ1% 1/2W blue-violet-green-yellow-brown 176731

r1 R8 15MΩ1% 1W brown-green-black-green-brown 181532

r1 R1 68 ΩPot 191311

r1 R25 1 KΩPot 191515

* NOTE: All fixed resistors are 1% tolerance (last stripe, brown). In some cases, resistors with a .5% tol-

erance (last stripe, green) may be used in place of the 1% resistors. Please ignore the tolerances printed

on the resistor card.

CAPACITORS

QTY SYMBOL VALUE MARKING PART #

r1 C2 (47 ) . 47 or . 22µF (473) or (223) 24478

Note: C1 is not used

SEMICONDUCTORS

QTY SYMBOL VALUE DESCRIPTION PART #

r4 D1 - D4 2CZ82P or 1N4148 Diode 314148

MISCELLANEOUS

-1-

QTY DESCRIPTION PART #

r1 PC Board 51 2C

r1 Fuse .5 Amp 533 4

r5 Solder . 62 551162

r2 Battery 1.5V AA 59 1

r1 Battery 9V 59 9

r1 Battery Snap 59 98

r1 Battery Contact Double 59 94

r2 Battery Contact Single 59 95

r1 Selector Contact * 61 1

r1 Thumb Wheel Knob 622 12

r1 Selector Knob * 622 18

r1 Top Cover Assembly 62312

r1 Back cover 6232 6

r1 Selector Base * 626 15

QTY DESCRIPTION PART #

r1 Screw 5/8 641573

r2 Fuse Clip 663 6

r3 Input Socket 664 2

r1 Ball Bearing * 6664 1

r1 Selector Spring * 68 2

r1 Manual Assembly 753 12

r1 Grease * 785

r2 Wire Bare 3/4 8344

r1 Wire 1 3/4 8345 1

r2 Wire 2 8345 2

r1 Wire 3 8345 3

r1h

FE Test Lead Set 8833

r1 Test lead set RWTL115

* These parts are part of the ma n rotary sw tch assembly. Th s may come preassembled by the factory.

-2-

CONSTRUCTION

Introduct on

Assembly of your M-115 Analog Multimeter Kit will prove to be an exciting project and give you much satisfaction and personal

achievement. If you have experience in soldering and wiring techniques, then you should have no problem with the assembly

of this kit. Care must be given to identifying the proper components and in good soldering habits. Above all, take your time

and follow these easy step-by-step instructions. Remember, An ounce of prevention is worth a pound of cure. Avoid making

mistakes and no problems will occur.

CAUTION: WEAR SAFETY GLASSES WHEN ASSEMBLING THIS KIT.

Assemble Components

In all of the following assembly steps, the components must be installed on the top side of the PC board unless otherwise indicated. The

top legend shows where each component goes. The leads pass through the corresponding holes and the board is turned to solder the

component leads on the foil side. Solder immediately unless the pad is adjacent to another hole which will interfere with the placement

of the other component. Cut excessive leads with a diagonal cutter. Then, place a check mark in the box provided next to each step to

indicate that the step is completed. Be sure to save the extra leads for use as jumper wires if needed.

Solder ng

The most important factor in assembling your multimeter is good soldering techniques. Using the proper soldering iron is of prime

importance. A small pencil type soldering iron of 25 - 4 watts is recommended. The t p of the ron must be kept clean at all

t mes and well t nned. Many areas on the PC board are close together and care must be given not to form solder shorts. Size

and care of the tip will eliminate problems.

For a good soldering job, the areas being soldered must be heated sufficiently so that the solder flows freely. Apply the solder

simultaneously to the component lead and the component pad on the PC board so that good solder flow will occur. Be sure that

the lead extends through the solder smoothly indicating a good solder joint. Use only ros n core solder of 60/40 alloy. DO NOT

USE ACID CORE SOLDER! Do not blob the solder over the lead because this can result in a cold solder joint.

1. Solder all components from

the copper foil side only.

Push the soldering iron tip

against both the lead and

the circuit board foil.

Component Lead

Soldering Iron

Circuit Board

Foil

2. First apply a small amount

of solder to the iron tip. This

allows the heat to leave the

iron and onto the foil.

Immediately apply solder to

the opposite side of the

connection, away from the

iron. Allow the heated com-

ponent and the circuit foil to

melt the solder.

Solder

Soldering Iron

Foil

Example 1

Poor solder connections occur

when the lead is not heated

sufficiently. The solder will not

flow onto the lead as shown. To

correct. reheat the connection

and, if necessary, apply a small

amount of additional solder to

obtain a good connection.

Solder does not flow onto the

lead. A hard rosin bead sur-

rounds and insulates the con-

nection.

Poor solder

connection

Mount Part

Soldering iron posi-

tioned incorrectly.

Example 2

A solder bridge occurs when

solder runs between circuit

paths and creates a short cir-

cuit. This is usually caused

by using too much solder. To

correct this, simply drag your

soldering iron across the sol-

der bridge as shown.

4. Here is what a good sol-

der connection looks like.

Cut off excess leads.

3. Allow the solder to flow

around the connection.

Then, remove the solder

and the iron and let the con-

nection cool. The solder

should have flowed

smoothly and not lump

around the wire lead.

Solder Soldering Iron

Foil

Bend Leads to Hold Part Solder and Cut Off Leads

Rx - 1 Ω5% 1/4W Resistor

(brown-black-brown-gold)

Foil Side

-3-

ASSEMBLE COMPONENTS TO THE PC BOARD

After each step, put a check in the box located next to the step that you have completed.

rInsert the three input sockets into the PC board holes as shown in Figure 1. Note that there is a lip on

one end of the input socket. The lip should rest on the legend side of the PC board. Solder the input

sockets to the PC board as shown in Figure 1. Apply enough heat to allow the solder to flow around the

input socket.

F gure A

68 ΩPot

F gure B

Capacitor C2

. 47 or . 22µF

F gure C

Diodes have polarity.

Mount them with the

band as shown on the

top legend.

Band

rR1 - 68 ΩPot

(see Figure A)

rD2 - 2CZ82P Diode

(see Figure C)

rR18 - 2KΩ1% 1/4W Resistor

(red-black-black-brown-brown)

rR24 - 18KΩ1% 1/4W Resistor

(brown-gray-black-red-brown)

rR19 - 44KΩ1% 1/4W Resistor

(yellow-yellow-black-red-brown)

rD3 - 2CZ82P Diode

rD4 - 2CZ82P Diode

(see Figure C)

rC2 - . 47µF or . 22µF Cap.

(473) or (223) (see Figure B)

R23 - 195KΩ1% 1/4W Resistor

(brown-white-green-orange-brown)

rR17 - 31KΩ1% 1/4W Resistor

(orange-brown-black-red-brown)

rR2 - 24 Ω1% 1/4W Resistor

(red-yellow-black-black-brown)

rR22 - 34KΩ1% 1/4W Resistor

(orange-yellow-black-red-brown)

rR21 - 2 Ω1% 1/4W Resistor

(red-black-black-black-brown)

rWire - 2 long

rR2 - 18.5Ω1% 1/4W Resistor

(brown-gray-green-gold-brown)

rR12 - .96Ω1% 1/2W Resistor

(black-white-blue-silver-brown)

rR11 - 1 Ω1% 1/4W Resistor

(brown-black-black-gold-brown)

-4-

F gure F

Battery snap - Insert red or white wire

through the hole marked B2+ and black or

blue wire through hole marked B2--. Then

solder wires to PC board.

F gure E

Insert fuse clips through the

PC board. Be sure tabs are

positioned as shown below.

Solder clips to PC board. Be

sure to heat clips thoroughly

when soldering. Install the

.5A fuse.

Tabs

R14 - 36 KΩ1% 1/4W Resistor

(orange-blue-black-orange-brown)

R15 - 1.8MΩ1% 1/2W Resistor

(brown-gray-black-yellow-brown)

R16 - 6.75MΩ1% 1/2W Resistor

(blue-violet-green-yellow-brown)

rD1 - 2CZ82P Diode

(see Figure C)

rWire - 2 Long

rR8 - 15MΩ1% 1W Resistor

(brown-green-black-green-brown)

rR7 - 4MΩ1% 1/2W Resistor

(yellow-black-black-yellow-brown)

rR6 - 8 KΩ1% 1/4W Resistor

(gray-black-black-orange-brown)

rR5 - 15 KΩ1% 1/4W Resistor

(brown-green-black-orange-brown)

rR3 - 5KΩ1% 1/4W Resistor

(green-black-black-brown-brown)

rR4 - 4 KΩ1% 1/4W Resistor

(yellow-black-black-red-brown)

rWire - 1 3/4 long

rWire - 3 long

rR1 - 1 2Ω1% 1/4W Resistor

(brown-black-red-black-brown)

rFuse Clips / Fuse .5A

(see Figure E)

rR9 - 3KΩ1% 1/4W Resistor

(orange-black-black-brown-brown)

R13 - 83.3KΩ1% 1/4W Resistor

(gray-orange-orange-red-brown)

rBattery Snap

(see Figure F)

rR25 - 1 KΩPot

(see Figure D)

Note: Make sure that the lead from

D1 doesnt short to R2, B2+ or R13.

F gure D

Mount the 1 KΩpot to the foil side of the PC board as

shown. Solder the leads to the foil side of the PC board.

1 kΩPot

Foil Side of PC Board

Red or White

Black or Blue

-5-

ASSEMBLE COMPONENTS TO THE PC BOARD

rSolder the shunt wire into the R26 (. 25Ω) position on the PC board as shown in Figure 2. The leads should extend

approximately 1/16 out of the bottom (solder side) of the PC board.

rBend the two 3/4 bare

wires as shown. Insert

one wire into the B1+

and -- slots on the PC

board. Bend the lead

over so it lays flat on

the copper pad. Solder

the two leads to the

copper pad as shown.

F gure 2

F gure 3

ASSEMBLE THE DIAL SELECTOR (Sk p f preassembled by the factory.)

rApply grease along the detent wall as shown in Figure 4.

rInsert the spring into the selector housing and apply a small amount of grease on top of the spring.

rPlace a ball bearing on top of the spring and carefully push it down into the housing.

rHolding the bearing in place, insert the housing into the case as shown in Figure 4. Keep holding the housing in

place of the ball bearing will come out.

rFrom the front of the case, align the selector knob shaft with the housing shaft and press together.

rAttach the selector contact to the selector housing by first inserting the tab on the contact into the notch on the

housing. Then, lay the contact on the housing as shown in Figure 4.

M+

M--

SOLDER METER MOVEMENT WIRES TO PC BOARD

rSolder the black wire from the meter movement to the hole marked M-- on the PC board (see Figure 3).

Solder the red wire from the meter movement to the solder pad marked M+ on the legend side of the PC board

(see Figure 3).

-6-

INSTALL THE FOLLOWING PARTS

rInstall the double battery contact as shown in Figure 5.

rInstall the two single battery contacts as shown in Figure 5. Solder the bare wires from B1 to the battery

contacts (as shown in Figure 5).

rInstall the the two AA batteries in the battery compartment. Be sure to observe the polarity markings on

the bottom of the battery compartment.

rConnect the battery snap to the 9 volt

battery and place the battery in the 9 volt

battery compartment.

rPlace the thumb wheel knob onto the Ω

ADJ pot located at the lower right of the

meter dial.

rInstall the back cover using the 5/8

screw as shown in Figure 6.

F gure 5

F gure 4

-7-

CALIBRATION

Meter Cal brat on (See Operating and Testing the Multimeter Section for meter operating instructions).

Obtain a voltage source of .1V as measured by an accurate voltmeter. The circuit of Figure 7 will work fine.

2. Set the range switch to .5VDC.

3. Connect the test leads as shown in Figure 7.

4. Adjust R1 for a reading of .1V (1 on 5 V scale) on the M-115 meter.

If a DC power supply or an accurate voltmeter is not available, then use a fresh 1.5V battery and adjust R1

to read 1.55V on the 2.5V scale (155 on 25 V scale).

Shunt W re Cal brat on

To calibrate the shunt wire, you will need a 5A current source like a 5V power supply and a 1Ω25 watt resis-

tor. If a 5A source is not available, you can use a lower current (2A). If no supply is available, it is not impor-

tant to do this test. Set the range switch to .25A/1 A position and connect the red and black test leads as

shown in Figure 8. Read the current on the -1 scale immediately below the meter mirror. If the meter

reads high, resolder the shunt wire so that there is less between the two mounting holes. If the meter reads

low, resolder the shunt wire so that there is more wire between the mounting holes.

F gure 6

F gure 7 F gure 8

TROUBLESHOOTING CHART

This chart lists the condition and possible causes of several malfunctions. If a particular part is mentioned

as a possible cause, check that part to see if it was installed correctly. Also, check that part and the parts

connected to it for good solder connections.

PROBLEM POSSIBLE CAUSE

No DC voltage reading 1. Check for open fuse.

Refer to Figure 7 for a better understanding 2.

Check resistors R2 through R9 for correct values and

of how the meter works. good solder connections.

3. Check that the PC board is seated properly and that

the three board clamps are engaged.

4. Check D3 and D4 for shorts.

5. Check R1 for an open connection.

6. Check the meter movement. Unsolder the red wire

from the meter movement to the PC board. Place a

51KΩresistor between the red wire and the positive

side of a 1.5V battery. Connect the negative side of

the battery to the black wire from the meter move-

ment. The meter should read a little over half scale.

Wrong meter readings 1. Check resistors R24, R25 and R2 through R9 for cor-

rect values and good solder connections.

No AC voltage reading 1. Check for open fuse.

Refer to Figure 8 for a better understanding 2. Check diodes D1 through D4 for opens and shorts.

of how the meter works. 3. Check resistors R13 through R16 and capacitor C1

for correct values and good solder connections.

No DC current reading 1. Check for open fuse.

Refer to Figure 9 for a better understanding 2. Check resistors R1 , R11, R12 and R26 for correct

of how the meter works. values and good solder connections.

Ohms 1. If meter cannot be zeroed:

Refer to Figure 1 for a better understanding A. Check for open fuse.

of how the meter works. B.

Check for weak or improperly installed batteries.

C. Check that the battery snap and battery con-

tacts are installed correctly.

D. Check resistors R19 through R25 for correct

value and good solder connections.

2. If meter does not read correctly:

A. Check R19 through R25 for correct value and

good solder connections.

No hFE reading 1. See Ohms above.

Refer to Figure 11 for a better understanding 2. Check that the test leads are in the correct socket

of how the meter works. for the type of transistor being tested.

-8-

-9-

OPERATING AND TESTING THE MULTIMETER

CAUTION: When measuring an unknown voltage or current, always start with the range switch set to the

highest scale. Then, if necessary, move the range switch down until the meter reads in the middle or right

half of the dial.

Checking your multimeter for proper operation is fairly easy. Of prime importance is knowing which scale

is read for each setting of the range switch. DC voltage is read on the dial immediately below the meter

mirror. This dial is marked with three scales with full scale readings of 1 , 5 and 25 . The -1 volt scale

is used for DC voltage ranges of .1, 1 and 1 VDC. The -5 volt scale is used for DC voltage ranges of

.5 and 5 VDC and the -25 volt scale is used for DC voltage ranges of 2.5 and 25 VAC. The readings taken

on these scales must be multiplied by the proper scale factor. For example, when the range switch is in

2.5VDC, a full scale reading on the -25 volt scale is actually 2.5 volts. You should therefore multiply you

reading by . 1 (move the decimal point 2 places to the left). DCmA are read using the same three scales

as DC volts.

AC volts are read on the red dial marked ACV using the same -1 , -5 and -25 scales as used for DC

volts. AC volts may also be read in decibels using the dB scale. The reference voltage ( dB) for the dB

scale is .775 volts. This voltage across 6 ohms dissipates 1mW of power. When dBs are read with the

range switch at 1 ACV, the dB scale is read directly. With the range switch at 5 ACV add 14dB. With the

range switch at 25 ACV add 28dB and at 1 ACV add 4 dB.

Ohms are read on the top scale. Multiply the reading by the appropriate factor 1, 1 , 1K or 1 K as indicat-

ed by the range switch.

If you are new to reading analog meter scales, assemble and try the Dial Scale Reading Exercise included

with this kit.

Before starting tests, set the meter needle to zero . The zero adjust screw is located on the meter face next

to the base of the needle. With no test leads connected, slowly turn this screw until the needle points to

zero on the -1 scale immediately below the meter mirror. We will now test each meter function. If the

meter should fail to perform as indicated, refer to the troubleshooting section for assistance.

DC Voltage Test

1) Plug the red test lead into the positive (+) socket, and the black lead into the --COM socket.

2) Set the range switch to 2.5VDC.

3) Connect the red lead to the positive side of a 1.5V battery (you may remove and use one of the 1.5V bat-

teries from the meter). Connect the black lead to the negative side of the battery. The meter should

read about 15 on the -25 scale. Move the decimal point 2 places to the left to obtain 1.5VDC.

4) Set the range switch to 1 VDC. The meter should read 1.5 on the -1 volt scale.

5) Set the range switch to 5 VDC. The meter should move about 1 1/2 small divisions on the -5 volt

scale.

Ohms Test

CAUTION: When measuring ohms, be sure that there is no voltage across the circuit being tested.

1) Plug the red test lead into the positive (+) socket, and the black lead into the --COM socket.

2) If you removed the 1.5 volt battery from the multimeter for the DC voltage test, replace it now.

3) Set the range selector switch to X1.

4) Short the test leads together and adjust the ΩADJ pot for a zero reading on the ohms (top) scale.

5) Connect the test leads to a known resistor between 1 and 1 ohms and observe the meter reading.

Multiply by the scale factor to obtain the resistance.

6) Set the range switch to X1 and repeat steps 4 and 5 using a 1 to 1K ohm resistor.

7) Set the range switch to X1K and repeat steps 4 and 5 using a 1K to 1 K ohm resistor.

8) Set the range switch to X1 K and repeat steps 4 and 5 using a 1 K to 1M ohm resistor.

Autres manuels pour M-1150K

Table des matières

Autres manuels Elenco Electronics Multimètre

Elenco Electronics

Elenco Electronics M-1000B Instructions de montage

Elenco Electronics

Elenco Electronics M-1000E Instructions de montage

Elenco Electronics

Elenco Electronics M-2785 Instructions de montage

Elenco Electronics

Elenco Electronics M-1750 Instructions de montage

Elenco Electronics

Elenco Electronics M-2625 Instructions de montage

Elenco Electronics

Elenco Electronics M-1000D Instructions de montage

Elenco Electronics

Elenco Electronics M-2671 Instructions de montage

Elenco Electronics

Elenco Electronics M-1250K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics ST-3030 Instructions de montage

Elenco Electronics

Elenco Electronics M-2666K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-1150K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-1700 Manuel utilisateur

Elenco Electronics

Elenco Electronics M-1008K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-1006K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-2665K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-2665K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-2795 Instructions de montage

Elenco Electronics

Elenco Electronics M-1150K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-1005K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics M-1740 Manuel utilisateur

Elenco Electronics

Elenco Electronics M-6100 Manuel utilisateur

Elenco Electronics

Elenco Electronics M-1007K Guide de l'utilisateur

Elenco Electronics

Elenco Electronics LCM-1950 Manuel utilisateur

Elenco Electronics

Elenco Electronics M-3900 Manuel utilisateur

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Amprobe

Amprobe Hexagon 60 Manuel utilisateur

Morris

Morris 57074 Manuel utilisateur