Elelabs ELU013 Manuel utilisateur

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 1

UG11: HOME ASSISTANT

This document describes how to use Elelabs Zigbee USB Adapter

(https://elelabs.com/products/elelabs_usb_adapter.html) with existing Home Automation platform

called Home Assistant (Hass.io) (https://www.home-assistant.io/).

Elelabs Zigbee USB Adapter firmware version, referenced in this guide: 6.3.0

Home Assistant (Hass.io) software version, referenced in this guide: 0.112.4

This guide focuses on:

-Connect Elelabs USB adapter to the target PC or Raspberry Pi

-Setup Zigbee Home Automation component in Home Assistant

-Troubleshooting

-Zigbee devices Pairing and Removal

-Zigbee devices examples

This guide DOES NOT focus on Home Assistant (Hass.io) installation and initial configuration. Please

follow the official instructions https://www.home-assistant.io/hassio/installation/.

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 2

Table of Contents

Introduction.......................................................................................................................................................................... 3

Initial setup and connection........................................................................................................................................... 4

Connect Elelabs USB Adapter to your Raspberry Pi or PC............................................................................... 4

Zigbee HA Component configuration.......................................................................................................................... 6

Configure Zha component .......................................................................................................................................... 6

Setup Logging (optional)............................................................................................................................................. 8

Zigbee HA Component Usage ......................................................................................................................................10

Add your devices to the Home Assistant .............................................................................................................10

Remove your device from Home Assistant .........................................................................................................11

Example: Philips Hue Bulb .......................................................................................................................................13

Example: Xiaomi Smoke Sensor .............................................................................................................................14

Troubleshooting................................................................................................................................................................15

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 3

Introduction

Elelabs Zigbee USB adapter can be used in 2 options with Home Assistant:

With a generic Linux machine, with Home Assistant installed

With a Raspberry Pi (any other single board computer) with Home Assistant installed

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 4

Initial setup and connection

This guide does not cover Home Assistant (Hass.io) installation. We assume, that you can access

Home Assistant Web Interface using your browser.

It is highly recommended to have SSH Server and Configurator addons installed, at least during the

Zigbee setup phase. To install them just follow the Hass.io installation guide (https://www.home-

assistant.io/hassio/installation/).

Connect Elelabs USB Adapter to your Raspberry Pi or PC

Once you have inserted the USB adapter, check the configuration.

-Wait for Hass.io to boot

-Connect to the web interface using your favourite browser

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 5

-Navigate to the Supervisor -> System -> Hardware menu

-Confirm the USB Adapter is detected and visible as serial ports (/dev/ttyUSB0 and in this

example)

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 6

Zigbee HA Component configuration

To work with Elelabs Zigbee USB Adapter from Home Assistant we are using Zigbee Home

Automation Component (https://www.home-assistant.io/components/zha/). It comes preinstalled

into Hass.io so we only need to configure it properly to get it working.

Configure Zha component

To setup Zigbee Home Automation component to work properly with Elelabs Zigbee Adapter we

need to:

-Navigate to the Configuration -> Integrations

-Add new Integration and search for Zigbee Home Automation

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 7

-Select Enter Manually

-Select EZSP radio type

-Enter /dev/ttyUSB0as Serial Port and select Baud rate 115200

-The installation should be successful

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 8

Now the Zigbee Integration should appear:

Setup Logging (optional)

To spot any potential issues it is good practice to enable logging, at least during the setup and

installation period. To do it, just add the following lines to the configuration file

/config/configuration.yaml:

logger:

default: warn

logs:

homeassistant.components.zha: debug

bellows.ezsp: debug

bellows.uart: debug

zigpy.zdo: debug

zigpy.application: debug

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 9

elelabs.com UG11: Home Assistant with Elelabs USB adapter rev. 0.4 | 10

Zigbee HA Component Usage

Once Zigbee Component is added and configured properly you can start to use it.

Add your devices to the Home Assistant

Open Configuration and go to Devices and Zigbee Coordinator

Start “Add Devices via this device”

When you will call it, you have 60 seconds to add the device.

Table des matières

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur