Electro-Craft EPS-HDM1004ECO Manuel utilisateur

EPS-HDM1004ECO

Encoder Modulator User Manual

About This Manual

Intended Audience

This user manual has been written to help people who have to use, to integrate and to

install the product. Some chapters require some prerequisite knowledge in electronics

and especially in broadcast technologies and standards.

Director

CHAPTER 1 INTRODUCTION ............................................................................................................... 1

1.1

RO UCT

VERVIEW

............................................................................................................................... 1

1.2

EATURES

........................................................................................................................................ 1

1.3

PECIFICATIONS

....................................................................................................................................... 1

1.4

RINCIPLE

HART

.................................................................................................................................... 2

CHAPTER 2 INSTALLATION GUIDE ................................................................................................... 3

2.1

ENERAL

RECAUTIONS

.......................................................................................................................... 3

2.2

OWER PRECAUTIONS

.............................................................................................................................. 4

2.3

EVICE

’

NSTALLATION

LOW

HART

LLUSTRATE AS FOLLOWING

..................................................... 4

2.4

NVIRONMENT

EQUIREMENT

................................................................................................................ 4

2.5

ROUN ING

EQUIREMENT

.................................................................................................................... 5

CHAPTER 3 WEB NMS OPERATION ................................................................................................... 5

3.1

OGIN

...................................................................................................................................................... 5

3.2

PERATION

.............................................................................................................................................. 6

CHAPTER 4 TROUBLESHOOTING ................................................................................................... 18

CHAPTER 5 PACKING LIST ................................................................................................................ 18

-16

EPS

H M

1004EC

Encoder Modulator

User Manual

Chapter 1 Introduction

1.1 Product Overview

EPS-H M1004ECO is a professional high integration device which includes encoding,

multiplexing, and modulating in one box. It supports 4 H MI inputs and VB-C/T RF out

with 2 adjacent carries and 2 MPTS out as mirror out of the 2 modulation carriers via ATA

(GE) port. This full function device makes it ideal for small CATV head end system, and it’s

a smart choice for hotel TV system, entertainment system in sports bar, hospital, apartment…

1.2 Ke Features

 Support LOGO, OSD and QR code insertion for ever local channel

(Language Supported:中文

中文中文

中文, English,

ﺔﻴﺑﺮﻌﻟﺍ

, ไทย, 󰬁

󰬁󰬁

󰬁, руская,

ﻭﺩﺭﺍ

, for more

languages please consult us…)

 4 HDMI input, MPEG-4 AVC/H.264 Video encoding

 MPEG1 La er II, LC-AAC，

，，

，HE-AAC audio encoding format and AC3 Pass

Through and support audio gain adjustment

 2 groups of multiplexing/modulating output channels

 2 DVB-T RF out

 Support64 IP inputs, 2 MPTS IP output over UDP and RTP/RTSP

Support PI remapping/PSI/SI editing and inserting

 Control via web management, and eas updates via web

1.3 Specifications

Input 4 H MI inputs, 64 IP inputs

Video

Encoding MPEG-4 AVC/H.264

Resolution

In-put

1920×1080_60P, 1920×1080_60i,

1920×1080_50P, 1920×1080_50i,

1280×720_60P, 1280×720_50P,

720×576_50i,720×480_60i,

Out-put

1920×1080_30P, 1920×1080_25P,

1280×720_30P, 1280×720_25P,

720×576_25P,720×480_30P,

Bit-rate 1Mbps~13Mbps each channel

Rate Control CBR/VBR

EPS

H M

1004EC

Encoder Modulator

User Manual

Audio

Encoding MPEG-1 Layer 2, LC-AAC, HE-AAC and AC3 Pass Through

Sampling rate 48KHz

Resolution 24-bit

Audio Gain 0-255 Adjustable

MPEG-1 Layer 2

bit-rate 48/56/64/80/96/112/128/160/192/224/256/320/384 kbps

LC-AAC bit-rate 48/56/64/80/96/112/128/160/192/224/256/320/384 kbps

HE-AAC bit-rate 48/56/64/80/96/112/128 kbps

Multiplexing

Maximum PI

Remapping 180 input per channel

Function PI remapping ( automatically or manually)

Generate PSI/ SI table automatically

Modulation VB-T

RF out 2*RF VB-T out (2 carriers combined

output)

Standard EN300 429/ITU-T J.83A/B

MER ≥40db

RF frequency 50~960MHz, 1KHz step

RF output level -25~-1dBm (82~105 dbµV), 0.1dBm

Symbol Rate 5.0Msps~7.0Msps, 1ksps stepping

J.83A J.83B

Constellation 16/32/64/128/256QAM 64/256 QAM

Bandwidth 7M 6M

Stream output RF output (F type interface)

2 IP MPTS output over U P/RTP/RTSP, 1*1000M Base-T Ethernet interface

S stem

function

Network management(WEB)

Chinese and English language

Ethernet software upgrade

Miscellaneous

imension(W×L×H) 482mm×328mm×44mm

Environment 0~45℃(work)；-20~80℃（Storage）

Power requirements AC 110V± 10%, 50/60Hz, AC 220 ±10%,50/60Hz

1.4 Principle Chart

-16

EPS

H M

1004EC

Encoder Modulator

User Manual

1.5 Appearance and Description

Front and Rear Panel Illustration

2 3 1 4 7 6 5

1 RF test and RF out port

2 Port Power supply and Grounding Pole

3 4 H MI inputs

4 ASI out (Optional)

5 Run and Power Indicators

6 ATA: IP input/output port (GE)

7 NMS (Network management port)

Chapter 2 Installation Guide

This section is to explain the cautions the users must know in some case that possible

injure may bring to users when it’s used or installed. For this reason, please read all

details here and make in mind before installing or using the product.

2.1 General Precautions

 Must be operated and maintained free of dust or dirty.

 The cover should be securely fastened, do not open the cover of the products when the

EPS

H M

1004EC

Encoder Modulator

User Manual

power is on.

 After use, securely stow away all loose cables, external antenna, and others.

2.2 Power precautions

 When you connect the power source, make sure if it may cause overload.

 Avoid operating on a wet floor in the open. Make sure the extension cable is in good

condition

 Make sure the power switch is off before you start to install the device

2.3 Device’s Installation Flow Chart Illustrated as following

2.4 Environment Requirement

Item Requirement

Machine Hall

Space

When user installs machine frame array in one machine hall,

the distance between 2 rows of machine frames should be

1.2~1.5m and the distance against wall should be no less than

0.8m.

Machine Hall Floor

Electric Isolation, ust Free

Volume resistivity of ground anti-static material:

1X10

~1X10

，Grounding current limiting resistance: 1M

(Floor bearing should be greater than 450Kg/㎡)

Environment

Temperature

5~40℃(sustainable )，0~45℃(short time)，

installing air-conditioning is recommended

Relative Humidity 20%~80% sustainable 10%~90% short time

Pressure 86~105KPa

oor & Window Installing rubber strip for sealing door-gaps and dual level

glasses for window

-16

EPS

H M

1004EC

Encoder Modulator

User Manual

Wall It can be covered with wallpaper, or brightness less paint.

Fire Protection Fire alarm system and extinguisher

Power

Requiring device power, air-conditioning power and lighting

power are independent to each other. evice power requires

AC 110V±10%, 50/60Hz or AC 220V±10%, 50/60Hz. Please

carefully check before running.

2.5 Grounding Requirement

 All function modules’ good grounding is the basis of reliability and stability of devices.

Also, they are the most important guarantee of lightning arresting and interference

rejection. Therefore, the system must follow this rule.

 Grounding conductor must adopt copper conductor in order to reduce high frequency

impedance, and the grounding wire must be as thick and short as possible.

 Users should make sure the 2 ends of grounding wire well electric conducted and be

antirust.

 It is prohibited to use any other device as part of grounding electric circuit

 The area of the conduction between grounding wire and device’s frame should be no

less than 25 mm

Chapter 3 WEB NMS Operation

Users can only control and set the configuration in computer by connecting the device to

web NMS Port. User should ensure that the computer’s IP address is different from this

device’s IP address; otherwise, it would cause IP conflict.

3.1 Login

The default IP address of this device is 192.168.0.136.

Connect the PC (Personal Computer) and the device with net cable, and use ping command

EPS

H M

1004EC

Encoder Modulator

User Manual

to confirm they are on the same network segment.

I.G. the PC IP address is 192.168.99.252, we then change the device IP to 192.168.99.xxx

(xxx can be 1 to 254 except 252 to avoid IP conflict).

Use web browser to connect the device with PC by inputting the Encoder & Modulator’s

IP address in the browser’s address bar and press Enter.

It displays the Login interface as Figure-1. Input the Username and Password (Both the

default Username and Password are “admin”.) and then click “LOGIN” to start the device

setting.

Figure-1

3.2 Operation

Summar →

→→

→ Status

When we login into encoder module, it displays the status interface as Figure-2.

Figure-2

User can click any item here to enter

the corresponding interface to check

information or set the parameters.

Current software version

information

-16

EPS

H M

1004EC

Encoder Modulator

User Manual

Parameters →

→→

→ Encoder

From the menu on left side of the webpage, clicking “Encoder”, it displays the

information of each encoding channel from the encoder as Figure-3.

Figure-3

Parameters →

→→

→ OSD:

Clicking “OS ”, it displays the interface as Figure-4/5/6 where to set Logo/ Caption/ QR

Code parameters.

Figure-4

General settings for

the Encoding program:

User can edit any item

listed as needed.

he light will turn green if there is source inputting

from module. Otherwise, the light will turn red.

elect to configure logo, caption or QRcode

Select program1-4 to apply the logo insertion, or

you can select “all” to apply all programs

Click here to confirm the LOGO you selected

Browse and select

the Logo which has

been created

Put your logo everywhere

EPS

H M

1004EC

Encoder Modulator

User Manual

Figure-5

Enter your text

here

Put your caption anywhere

Select the text color and

background color

Set when to show caption. So do

Logo and QRCode.

Table des matières

Manuels Modulateur populaires d'autres marques

axing

axing AVM 5-00 Manuel utilisateur

IKUSI

IKUSI MAC-HOME HD Manuel utilisateur

Wisi

Wisi MINI OM 10 Manuel utilisateur

RCA

RCA CRF910 Manuel utilisateur

Pico Macom

Pico Macom PM45 Manuel utilisateur

FTE Maximal

FTE Maximal MODIG AIR Manuel utilisateur

Thor Broadcast

Thor Broadcast H-IP-32RF Manuel utilisateur

Delphi

Delphi SA10003 Manuel utilisateur

Elan

Elan MOD3000 Manuel utilisateur

ClearView

ClearView SD4260 Manuel utilisateur

Televes

Televes T.0X COFDM-QAM CI Manuel utilisateur

Crucial Audio

Crucial Audio Die Gotterdämmerung Manuel utilisateur

Pioneer

Pioneer CD-V61FM Manuel utilisateur

Televes

Televes 554912 Manuel utilisateur

Newtec

Newtec M6100 Manuel utilisateur

ProTelevision

ProTelevision PT 5780 Manuel utilisateur

Argent Cables

Argent Cables HD DVB-T MODULATOR Manuel utilisateur

SSS Siedle

SSS Siedle BVM 650-0 Manuel utilisateur