Elation Palm Copilot Manuel utilisateur

Palm Copilot

Rev 1.2

P/N:24-004-2295-00

Introduction

Features

Congratulations and thank you for purchasing the Elation Palm Copilot. The Palm Copilot is a simple 8

channels DMX controller and may be used to link with LC-8P series relay pack for control.It is available

in DMX output and Analog output mode.

USITT DMX512(1990 protocol) control

Be available in DMX output and ANALOG output(Selectable)

Specifications

Power Input...................................................................................DC9~12V

Channel Output ..........................................DMX output and Analog output

Connects ...................................................3-pin XLR connector & DB-9pin

Dimensions........ ................................................................. 120x80x35mm

Total Weight.........................................................................................240g

Power by external adaptor or battery

Output modes was programmed by 10 way DIP-Switch

Touch button

Power failure memories

Accessories...........................................AC/DC Adaptor UL/VDE(included)

...........Cradle(Sold Separately)

Cradle(Sold Separately)

Function Instructions

Made in PRC

DC IN: 9-12V 200mA Min. ON OFF DMX

Out

Control Output 1-8

10987654321

Control Output 1-8

1=+12V

2=CH4

CH 3

CH 2

5=CH1

CH 8

CH 7

CH 6

9=CH5

10= GND

DMX Address Setting

1234 567 8910

ON RS

128

256

DMX

Analog

789

Palm Copilot

1.Touch button (Indicator) 1~8

2.DC socket: Connects power input with DC 9~12V,200mA Min

3.Power Switch: Used to power on/off the unit

4.DB-9: Connects relay pack to control output 1~8

5.3-pin XLR female connector: Connects lighting fixtures and output DMX signal

6.Dip-switch 1~10: Programs output mode

Front Panel Rear panel

7.Battery cover

Top View

Operation Guide

The user can flip the dip-switch 10 to "on" or "off" position to select the DMX output or Analog output.

1. DMX output mode

123456789

ON RS

OFF 10

Flip the dip-switch 10 to "on" position, the Palm Copilot goes into DMX output mode.

In this mode, the DIP-switch 1~9 were used to set the initializing DMX address, the 8 buttons in interface

of the unit are corresponding to output the 8 channels DMX .

When the DIP-switch 1~9 is flipped to "on", all the back light of the 8 buttons light up, the corresponding

channel outputs the DMX with value of 255.

When the DIP-switch 1~9 is flipped to "off",all the back light of the 8 buttons black out,the corresponding

channel outputs the DMX with value of 0.

2. Analog output mode

123456789

ON RS

OFF 10

Flip the dip-switch 10 to "off" position, the Palm Copilot goes into Analog output mode. At this time, the

Palm Copilot enables to connect the Relay Pack such as LC-8P series which from Elation.

In this mode, the 8 buttons in interface of the unit are corresponding to output the 8 channels contact

capacitity .

When tap the button 1~8 and make it "on", the back light of the corresponding button lights up , the

output of the corresponding relay pack channel is "ON".

When tap the button 1~8 and make it "off", the back light of the corresponding button blacks out , the

output of the corresponding relay pack channel is "OFF".

1,2,4

3,4

1,3,4

2,3,4

1,2,3,4

1,2,3,4,5,6,7,8,9

1,2

1,3

2,3

1,2,3

1,4

2,4

DMX ADDRESS (SLAVE)

SWITCHES ON SWITCHES ON

(Dip Switch 10 = on)

START

CH#

START

CH#

511

1234 567 8910

ON RS

DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication

between intelligent fixtures. Each dip switch represents a binary value.

A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish

to achieve, for example:

Setting DMX address for 21.

Flip switches1,3,&5 to the

"ON" position

Setting DMX address for 201.

Flip switches1,4,7,& 8 to the

"ON" position

Dipswitches# Value

1=1

3=4

5=16

=21

Dipswitches# Value

1=1

4=8

7=64

8=128

=201

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Setting DMX Addressing

While a DMX initializing address is set as 21, on the Palm Copilot interface, the button 1 is corresponding

with 21, the button 2 is corresponding with 22, the rest may be deduced like this. Meanwhile, all the 8

buttons back light are lit and the device output the DMX value with 255, the user may press the touch

button to select the desired channel to send DMX signal or not.

INPUT

DB-9PIN Configuration

1---- +DC 12 V

2---- Channel 4

3---- Channel 3

4---- Channel 2

5---- Channel 1 Housing---- DC 12 V, Grounded

9---- Channel 5

8---- Channel 6

7---- Channel 7

6---- Channel 8

2345

789 GND

Output (Female)

Note

2)While powered by the battery, the indicator of the buttons will fade out in 5 seconds without operation

for saving power. While around 10% of the power capacity be left, the indicator of the power source will

repeatedly flash to prompt that the unit is in the lower power capacity.

1)Synchronously hold down the button 1, 6 and 8, may swap between the key tone on and the key tone

off.

3-Pin XLR connector Configuration

If you are constructing your own data cables, be sure to use standard two conductor shielded cable

(This cable may be purchased at almost all professional sound and lighting stores). Your cables should

be made with a 3-pin male and female XLR connector on either end of the cable. Also remember that

DMX lines must be daisy chained and can't be split.

The Palm Copilot requires a standard 3-pin XLR connector for data output. Connect the Palm Copilot

and your fixtures together using standard 3 pin DMX cables.

DMX Cable Requirements

*Note:

Be sure to above figures when making your own cables. Do not use the ground lug on the XLR

connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor

to come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and

erratic behavior.

DMX 512 OUT

3-PIN XLR

DMX 512 IN

3-PIN XLR

COMMON

DMX+

DMX-

XLR Male Socket XLR Female Socket

1 Ground 2 Cold

3Hot 3Hot

2 Cold 1 Ground

XLR Pin Configuration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Table des matières

Autres manuels Elation Équipement d'éclairage

Elation

Elation PowerWash 250 Manuel utilisateur

Elation

Elation Focus Spot 250R Manuel utilisateur

Elation

Elation CUEPIX BLINDER WW4 Manuel utilisateur

Elation

Elation UNI BAR Manuel utilisateur

Elation

Elation SATURA SPOT LED PRO Manuel utilisateur

Elation

Elation ELAR EXTQW FLOOD HP Manuel utilisateur

Elation

Elation DJ Equipment Manuel utilisateur

Elation

Elation Active Wave 250 Manuel utilisateur

Elation

Elation PLATINUM BEAM 5R XM485-V1.0-NR Manuel utilisateur

Elation

Elation DW PROFILE Manuel utilisateur

Elation

Elation ProColor Manuel utilisateur

Elation

Elation PROTEUS RAYZOR BLADES Manuel utilisateur

Elation

Elation CRISP Manuel utilisateur

Elation

Elation ELAR EXTQW FLOOD HP Manuel utilisateur

Elation

Elation ELAR 180 Par RGBAW Manuel utilisateur

Elation

Elation FUZE PENDANT COMPACT Manuel utilisateur

Elation

Elation CMY Zoom 575 Manuel utilisateur

Elation

Elation DM-2512R Manuel utilisateur

Elation

Elation PIXEL DRIVER 4000 Manuel utilisateur

Elation

Elation ELED STRIP 50RGB Manuel utilisateur

Elation

Elation RMD-1210 Manuel utilisateur

Elation

Elation streamer Manuel utilisateur

Elation

Elation CYBER PAK Manuel utilisateur

Elation

Elation Event MH Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur