Elation Design LED 12 Brick II Manuel utilisateur

Rev. 03/08/08

Design LED 12 Brick II

Elation Professional™

6122 S. Eastern Ave.

Los Angeles, CA. 90040

www.elationlighting.com

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com

TABLE OF CONTENS

CONTENTS

1. General Information………………………………………………………………………2

a. Introduction……………………………………………………………………….2

b. Unpacking………………………………………………………..…………..… 2

c. Customer Support…………………………………………….………………… 2

d. Warranty Registration……………………………………………………..…… 3

2. Safety Instructions………………………………………………………........…………. 4

3. Features……………………………………………………………………………………6

4. General Guidelines……………………………………………………………………….7

5. Fixture Overview…………………………………………………………………………. 8

6. Mounting and Installation………………………………………………………….……. 10

7. Understanding DMX……………………………………………………………………...13

a. DMX Connections………………………………………………………………. 16

b. DMX Terminator…………………………………………………………………. 16

c. 3-Pin to 5-Pin Conversion……………………………………………………….16

d. Understanding DMX Addressing.………………………………………………16

8. Operation Modes….………………………………………………………………………17

a. DMX Mode Selection…………………………………………………………….19

b. Manual Settings…………………………………………………………………. 19

9. DMX Traits…………………………………………………………………………………20

10. Cleaning and Maintenance………………………………………………………………24

11. Warranty…………………………………………………………………………………...25

12. Photometric Data………………………………………………………………………… 27

13. Dimensional Drawings………………………………………………….……………….. 28

14. Change lens to get different beam angles……………………………………………. 28

15. Circuit Schematic………...……………………………………………………………….29

16. Technical Specifications…………………………………………...………….………… 30

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com

1. GENERAL INFORMATION

INTRODUCTION: Congratulations, you have just purchased one of the most innovative and

reliable LED fixtures on the market today! The Design LED 12 Brick II ™, has been designed

to perform reliably for years when the guidelines in this booklet are followed. Please read

and understand the instructions in this manual carefully and thoroughly before attempting to

operate this unit. These instructions contain important information regarding safety during

use and maintenance.

UNPACKING: Thank you for purchasing the Design LED 12 Brick II ™ by Elation

Professional®. Every Design LED 12 Brick II ™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping carton for damage that

may have occurred during shipping. If the carton appears to be damaged, carefully inspect

your fixture for damage and be sure all accessories necessary to operate the fixture have

arrived intact. In the event damage has been found or parts are missing, please contact our

customer support team for further instructions. Please do not return this unit to your dealer

without first contacting customer support at the number listed below.

Inside the box you should find: the fixture, a DMX XLR cable, an IEC power cable, an IEC

“jumper” power cable, a safety cable, and this manual. Please contact customer support at

the number listed below if any of the above items are missing.

CUSTOMER SUPPORT: Elation Professional®provides a customer support line, to provide

set up help and to answer any question should you encounter problems during your set up

or initial operation. You may also visit us on the web at www.elationlighting.com for any

comments or suggestions. For service related issue please contact Elation Professional®.

Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.

Voice: (323) 582-3322

Fax: (323) 582-3108

E-mail: [email protected]

Forum: www.ElationLighting.com/forum

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com

rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself. Doing so will void your manufactures warranty.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

WARRANTY REGISTRATION: The Design LED 12 Brick II ™ carries a two year (730 days)

limited warranty. Please fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written

on the outside of the return package. A brief description of the problem as well as the R.A.

number must also be written down on a piece of paper and included in the shipping

container. If the unit is under warranty, you must provide a copy of your proof of purchase

invoice. Items returned without a R.A. number clearly marked on the outside of the package

will be refused and returned at customer’s expense. You may obtain a R.A. number by

contacting customer support at (323) 582-3322.

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com

2. SAFETY INSTRUCTIONS

To guarantee proper and consistent operation, it is important to

follow the guidelines in this manual. Elation Professional will not

accept responsibility for damages resulting from the misuse of

this fixture due to the disregard of the information printed in this

manual.

1. Always be sure that the fan and the air inlets remain clean and are never

blocked. Allow about 6” (15cm) between this fixture and other devices or a wall

to allow for proper cooling.

2. Never touch the fixture during normal operation.

3. Never look directly into the lamp beam. You risk injury to your retina, which may

induce blindness.

4. For safe operation, follow the Installation guide described in chapter two of this

manual. Operating the Design LED 12 Brick II ™ without suited safety aids such

as safety cables or clamps can increase the risk of damage and/or personal

injury.

5. Installation should only be performed by qualified and certified personal.

6. When mounting this fixture, use only the original rigging points included with this

fixture. Any structural modification will void the original manufactures warranty

and may increase the risk of damage and/or personal injury.

7. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.

8. Do not attempt to operate this fixture if the power cord has become damaged or

frayed.

9. Never open this fixture while in use.

10.This device falls under protection-class I. Therefore it is essential that the device

be grounded properly.

11.All electrical connections must performed by qualified personal.

12.Be sure the available voltage matches the voltage requirements of the unit. Be

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com

sure the power cord is never crimped or damaged. If the power cord is damaged,

replace it immediately with a new one of similar power rating.

13.Always disconnect from main power before performing any type of service or

any cleaning procedure.

14.Only handle the power cord by the plug. Never pull out the plug by tugging the

wire portion of the cord.

15.Please be aware that damages caused by modifications to the device are

not subject to warranty.

Important Notice: Damages resulting from the disregard of safety and general user

instructions found in this user manual are not subject to any warranty claims.

Never look directly into the light source,

as sensitive persons may suffer an epileptic shock.

Never touch the device during operation!

The housing may heat up

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com

3. FEATURES

• Low power consumption

• Minimal heat emission

• Maintenance free operation

• Equipped with 12 one-watt LEDS: (4 red, 4 green, 4 blue)

• High power LEDS manufactured by Lumileds, USA

• 100,000 hours rated LED life

• Seamless RGB color changing

• USITT DMX-512 complaint

• 5-pin and 3-pin Male and Female XLR Data Connectors

• Preprogrammed colored macros

• Strobe-effect with a maximum flash rate of 18fps

• DMX-controlled operation or stand-alone operation with Master/Slave-function

• 8 built-in programs accessed via DMX-controller or manually

• Sound-controlled via built-in microphone

• Individual control over each LED

• Electronic/Switching power supply (100v~240V 50/60Hz)

• Three DMX Modes:

15 DMX-channels

12 DMX-channels

4 DMX-channels

3 DMX-channels

• Flicker-free operation for television and film

• Compact design: fits in 12” box truss

• Brilliant light output

• Linkable power supply (in and out power connectors) up to 8 units.

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com

4. GENERAL GUIDELINES

This fixture is a professional lighting effect designed for use on stage, in nightclubs, in

theatres, and other types of architectural installations. Do not attempt operation or

installation without a proper knowledge on how to do so.

This fixture was designed for indoor use only; use of this fixture outside will void the

manufacture’s warranty.

Consistent operational breaks will ensure that the fixture will function properly for many

years to come.

Do not shake the fixture around.Avoid brute force when installing or operating the fixture.

While choosing an installation location, please be sure that the fixture will not be exposed to

extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat

surface should be at least .5 meter (about 1.5ft).

Always install the fixture with an appropriately rated safety cable. When installing the fixture

in a suspended environment always be sure to use mounting hardware no less than M10 x

25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.

Do not attempt to operate this fixture until you have familiarized yourself with all of its

functions.

Do not permit operation by persons not qualified for operating this type of theatrical fixture.

Most damages are the result of improper operation.

Please use the original packaging to transport the fixture in for service.

For your own safety, please read this user manual carefully before installing the device.

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com

5. FIXTURE OVERVIEW

456789

11 12 13 14

1. Bracket Locking Knob – This knob is used to secure the bracket in place after

angle adjustments have been made.

2. Diffusing Lens – This lens is used to both protect the LEDS as well as diffuse the

light output.

3. LED Assembly – RGB LED assembly 3x1watt LEDS

Design LED 12 Brick II ™

©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com

4. On/Off Power Switch – Controls main power to the unit.

5. Power Output Jack – Use this jack to jump power to another Design LED 12 Brick II

™

6. Power Input/Fuse Holder Assembly – This assembly holds the safety fuse as well

as provides a female IEC connector for a power cord. Always replace the fuse with

an exact match unless otherwise specified by an authorized Elation Service

Technician. Using a fuse other than that specified could seriously damage the unit

and will void your manufactures warranty.

7. Eye-Bolt - Use this bold as a safety-cable rigging point. Always secure any installation

with a properly rated safety-cable.

8. LED MENU DISPLAY –Four segment LED menu display, details all menu functions

9. DMX In Jack – This jack accepts an incoming DMX signal via a male, 3-pin or a 5-pin

XLR jack.

10.DMX Out Jack - This jack is used to send an incoming DMX signal to the next fixture

in the DMX chain via a female, 5-pin XLR jack.

11.ESC BUTTON – This button is used to access and exit the fixture’s on-board menu

system.

12.UP BUTTON – This button is used to scroll forward when navigating through the

fixture’s menu system.

13.DOWN BUTTON – This button is used to scroll backwards when navigating through

the fixture’s menu system.

Autres manuels pour Design LED 12 Brick II

Table des matières

Autres manuels Elation Équipement d'éclairage

Elation

Elation Color Spot 575 Manuel utilisateur

Elation

Elation COLOUR 5 PROFILE Manuel utilisateur

Elation

Elation Event Cylinder DMX Manuel utilisateur

Elation

Elation Power Spot 700 Manuel utilisateur

Elation

Elation KL FRESNEL 8 CW Manuel utilisateur

Elation

Elation PLATINUM BX Manuel utilisateur

Elation

Elation Joy 150 Manuel utilisateur

Elation

Elation SNIPER 2R Manuel utilisateur

Elation

Elation Design LED 36 Tri-Brick Manuel utilisateur

Elation

Elation SIXBAR 500 Manuel utilisateur

Elation

Elation Professional SIXPAR 200IP Manuel utilisateur

Elation

Elation SC-816 Manuel utilisateur

Elation

Elation CUEPIX BLINDER WW2 Manuel utilisateur

Elation

Elation 6+ Series Manuel utilisateur

Elation

Elation Design LED 36MH Manuel utilisateur

Elation

Elation Design Spot 1200C Manuel utilisateur

Elation

Elation Design LED 12 Brick II Manuel utilisateur

Elation

Elation ELAR PAR 72 UV Manuel utilisateur

Elation

Elation Design LED Par Zoom MH Manuel utilisateur

Elation

Elation Outdoor LED Par Fixture ELAR EXPAR Manuel utilisateur

Elation

Elation DJ Equipment Manuel utilisateur

Elation

Elation MAGIC-260 Manuel utilisateur

Elation

Elation SIXPAR 300WMG Manuel utilisateur

Elation

Elation Design LED 60 TriStrip Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur