Ei Electronics Ei2110 Manuel utilisateur
Contains vital information on unit operation and installation. Read and retain carefully.
If you are just installing this unit this leaflet MUST be given to the householder.
Model: Ei2110
INSTALLER INSTRUCTIONS
MULTI-SENSOR FIRE ALARM
with Rechargeable Lithium Cell Back-up
230V~
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 1
2
3
4
5
6
7
9
13
14
15
16
17
19
23
25
1. QUICK GUIDE
1.1 INSTALLATION GUIDE
1.2 ALARM REMOVAL
2. MULTI-SENSOR FIRE ALARM FEATURES
3. HOW MANY ALARMS TO INSTALL
3.1 CATEGORIES OF SYSTEM
3.2 SELECTING ALARM TYPE
3.3 GRADE D, E & F SYSTEMS
4. POSITIONING ALARMS
4.1 LOCATIONS TO AVOID
5. INSTALLATION
5.1 MOUNTING & WIRING ALARMS
5.2 INTERCONNECTING ALARMS
6. ACCESSORIES
CONTENTS
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 2
3
INSTALL IN THE CENTRE OF CEILING AT LEAST 300mm FROM
LIGHT FITTINGS & WALLS
ENSURE MAINS POWER IS CORRECTLY CONNECTED TO L & N
TERMINALS ON ALL INTERCONNECTED ALARMS - OTHERWISE
UNITS WILL BE DAMAGED
DO NOT FIT ACTUAL ALARMS UNTIL ALL BUILDING WORK IS
COMPLETED TO AVOID CONTAMINATION. AFTER CHECKING
OPERATION, COVER ALARMS WITH DUST COVER UNTIL
REQUIRED FOR USE
DISCONNECT THE ALARMS BEFORE APPLYING HIGH VOLTAGE
TO WIRING (FOR INSULATION TESTS)
DO NOT ATTEMPT TO OPEN THE ALARM AS IT IS PERMANENTLY
SEALED FOR SAFETY
INTERCONNECT ALL ALARMS
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 3
4
1.1 Installation Guide
GREEN MAINS
LIGHT
AS THE TAMPER-PROOF CATCH ENGAGES. SWITCH ON MAINS
PRESS AND HOLD THE TEST BUTTON ON THE ALARM. CHECK
THE ALARM AND ANY INTERCONNECTED UNITS SOUND.
DECIDE ON CORRECT POSITION
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 4
5
1.2 Alarm Removal
LOCATE REMOVAL SLOT
LOCATE THE ARROW ON THE FRONT FACE OF THE ALARM.
THE SLOT IS LOCATED DIRECTLY ABOVE THE ARROW.
INSERT SCREWDRIVER
INSERT A FLAT-BLADED SCREWDRIVER HORIZONTALLY
ABOUT 10mm INTO THE CENTRE OF THE REMOVAL SLOT
SLIDE ALARM OFF BASE
WITH THE SCREWDRIVER STILL INSERTED, PUSH THE LOWER
HALF OF THE ALARM AWAY FROM THE SCREWDRIVER, IN THE
DIRECTION OF THE ARROW ON THE COVER
HOLD THE LOWER HALF OF THE ALARM AND REMOVE FROM
THE BASE PLATE BY LOWERING THE ALARM TOWARDS
THE FLOOR.
REMOVE ALARM
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 5
2. MULTI-SENSOR FIRE ALARM FEATURES
The state of the art EI2110 Multi-Sensor Fire Alarm, with its Heat enhanced Optical
Smoke Sensor, has a significantly improved performance as described below.
1. Faster Response to a wider range of fires.
The combination of the ultra fast temperature sensing thermistor and the high
performance optical sensor within the unit, enhances the fire sensing performance
such that the unit detects all the 7 different Test Fires (TF) specified in the standard
BS ISO 7240-15: 2004. These Test Fires are designed to produce different levels of
smoke/heat and as such are a good test of the units performance to the different fires
that could possibly occur in the home.
2. Reduced Nuisance Alarms.
The unit can tolerate up to 50% higher levels of cooking fumes and steam when
compared with normal optical sensor alarms.
3. Increased Longevity and Ruggedness.
The unit can tolerate up to 100% more dust and contamination build-up when
compared with normal optical sensor alarms. This is due to the unique automatic
DUST* compensation built into the unit which monitors the contamination in the smoke
sensing chamber and adjusts the alarm trigger point accordingly.
*DUST – Dust Ups Sensor Threshold.
Additionally, the optical sensor chamber features a fine mesh insect screen that is
bonded to the plastic of the chamber. This significantly improves immunity to insect
contamination.
6
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 6
7
4. Replace Alarm Indicator.
If the optical sensor chamber becomes very heavily contaminated, the amber fault
light will flash once every 40 seconds to inform the user. Action can then be taken to
replace the unit, long before the contamination causes nuisance alarms.
5. Alarm Memory.
After a the unit has gone into alarm, the red alarm light will flash twice (1 second apart)
every 40 seconds to indicate that the unit has alarmed in the previous 24 hours.
Additionally, pressing the Test/Hush button on this unit will cause it to emit short, rapid
beeps instead of the normal alarm sound. Both these features allow easy
identification, for example, of the source of nuisance alarms during the night.
6. Single Person Interconnect Test
Pressing and holding the Test button on the unit causes the alarm to sound. On
releasing the test button, the alarm will immediately cease but all interconnected
alarms will continue to sound for 3 seconds. This allows easy audible check of alarm
interconnection.
3. HOW MANY ALARMS TO INSTALL
- CATEGORIES & GRADES -
The ideal system would consist of Multi-Sensor Fire Alarms installed throughout the
dwelling apart from the kitchen which should have a Heat Alarm installed (Note:
alarms should not be installed in toilets/bathrooms).
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 7
The Multi-Sensor Alarm can be installed for superior performance anywhere the
regulations specify an Optical Smoke Alarm or an Ionisation Smoke Alarm.
(The Ei2110 Multi-Sensor Fire Alarm can also be used and interconnected with an
Ei166RC Optical Smoke Alarm or an Ei161RC Ionisation Smoke Alarm if necessary).
The advice here follows the guidance in British Standard BS 5839-Part 6:2004 in
general (for further information see the BS standard itself).
The main reason for fitting alarms in dwellings is to ensure that when there is a fire,
sufficient early warning is given so that everybody can escape safely.
This means that the fire alarms should ideally be located in all escape routes and in all
rooms that contain potential sources of fire. Another important consideration is that the
alarm should be heard throughout the house – particularly in the bedrooms.
It is also important that nuisance/false alarms are minimised to ensure the units are
not disabled or ignored.
BS 5839-Part 6:2004 gives guidance on:
- how many alarms to install
- what type of alarm to use
- where to position alarms
The above points will depend on the type of dwelling to be protected and the level of
fire risk.
Fire Risk Assessment
The ‘Grade’ and ‘Category’ of system that should be installed depends on the fire risk.
8
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 8
It is therefore recommended that a Fire Risk Assessment is undertaken. The Risk
Assessment would be based on a combination of probabilities:
- fire occurring
- injury or death to occupant
- system operating correctly with a fire
- early detection and warning to occupants in the event of a fire.
The greater the risks, the more comprehensive and reliable systems are needed.
3.1 Categories of System
There are three Categories of LD systems for Life protection in Dwellings that can be
installed, depending on the fire risk and regulations.
Please see following pages for detailed information.
9
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 9
10
for existing dwellings
MINIMUM PROTECTION
LD3
Minimum Protection LD3:
Alarms in all hallways,
stairways and circulation areas that form part of the
escape routes from the dwelling.
Multi Storey Dwelling LD3
Living
Room
Bedroom Bathroom
Kitchen
Bedroom Shower
Garage
Multi-Sensor Fire Alarms located:
on each storey
every 7.5 m of hallways and escape routes
within 3m of all bedroom doors
(apart from toilets & bathrooms )
Bedroom
Bedroom Bedroom
Kitchen / Dining Room
Living Room
Bathroom
Single Storey Dwelling LD3
do not fit alarmMulti-Sensor Fire Alarm
B16350-R0-Ei2100 SERIES-U&C.qxd 18/9/08 3:46 PM Page 10
Autres manuels pour Ei2110
1
Table des matières
Autres manuels Ei Electronics Détecteur de fumée
Ei Electronics
Ei Electronics B16009-R0-160RC Series Manuel utilisateur
Ei Electronics
Ei Electronics Ei161RC Ionisation Manuel utilisateur
Ei Electronics
Ei Electronics Ei605MTYRF Manuel utilisateur
Ei Electronics
Ei Electronics Ei141EK Manuel utilisateur
Ei Electronics
Ei Electronics aico Ei146e Manuel utilisateur
Ei Electronics
Ei Electronics Ei 175 Ionisation Manuel utilisateur
Ei Electronics
Ei Electronics EI 100S Silencer Manuel utilisateur
Ei Electronics
Ei Electronics Ei144 Heat Manuel utilisateur
Ei Electronics
Ei Electronics Ei154TL Manuel utilisateur
Ei Electronics
Ei Electronics Ei141 Ionisation Manuel utilisateur
Ei Electronics
Ei Electronics Ei161e Manuel utilisateur
Ei Electronics
Ei Electronics Ei128R Manuel utilisateur
Ei Electronics
Ei Electronics Ei 156TLR Optical Manuel utilisateur
Ei Electronics
Ei Electronics RadioLINK Ei170RF Manuel utilisateur
Ei Electronics
Ei Electronics Ei 105B Manuel utilisateur
Ei Electronics
Ei Electronics Ei146 Optical Manuel utilisateur
Ei Electronics
Ei Electronics Ei 176 Optical Manuel utilisateur
Ei Electronics
Ei Electronics Ei151TL Instructions d'installation
Ei Electronics
Ei Electronics Ei160e Series Manuel utilisateur
Ei Electronics
Ei Electronics Easichange Series Manuel utilisateur
Manuels Détecteur de fumée populaires d'autres marques
System Sensor
System Sensor DH500ACDC Manuel utilisateur
Resolution Products
Resolution Products RE612 CryptiX Manuel utilisateur
First Alert
First Alert PC900V Manuel utilisateur
Eminent
Eminent EM6590 E-Domotica Manuel utilisateur
Carrier
Carrier Kidde Quell Q301 Manuel utilisateur
VESDA
VESDA VLF-500 Manuel utilisateur
