Edison Autoslide Manuel utilisateur

Installation Manual

(For Sliding Garage Doors)

Edison Autoslide™

Parts List

1. Connector Sleeve (1x)

2. Two-part channel and plasc chain (1x)

3. C-rail (2x)

4. Carriage (1x)

5. Door bracket (1x)

6. Control housing with cord (1x)

7. Tensioner, tensioning bolt M8 x 80mm, and spring (1x)

8. Angle bracket for rail mid-aachment (4x)

9. Thick washer 1-1/4” dia (4x)

10. U-ng long stud with collar (1x)

11. U-ng short bolt (1x)

12. Long pin and clips OR lock nut/bolt (2x)

13. Medium pin and clip OR lock nut/bolt (1x)

14. Short pin and clip OR lock nut/bolt (2x)

15. Lag bolt 5/16” x 1-1/2” (10x)

16. Carriage bolt M8 x 25mm, lock washer and nut (4x)

17. Release cord grip (1x)

18. Electric end (1x) *NOT USED*

19. Non-electric end (1x)

20. Electric end with cord (1x)

21. Photoeye set (1x)

22. Rail mid-aachment bracket (2x)

23. Wall buon (1x)

24. Remote transmier (2x)

25. Boomerang curved brace (1x)

26. Limit stop set (marked “H” and “V”) (1x)

27. Rail end bracket (2x)

123

78910 11

12 13 14 15 16

21 22 23

25 26

Assembly

The chain is inserted into a plasc guide channel. It is not

packaging material. Do not throw away! Unfold the two

secons of chain. You may leave the limit stops “H” and

“V” in the rail.

Aach release cord grip to the carriage cord by sliding it

on and knong the cord. Hang the chain out as shown

and thread it onto the sprocket on the underside of the

carriage. Note the posion of the chain with guide as

shown in the side view at le. If the sprocket does not

turn, pull the release cord one me. This unlocks the

carriage.

Slide the carriage and chain assembly onto one secon of

C-Rail to the approximate mid-posion.

Assembly

Slide both secons of rail into the connecng sleeve.

Thread the chain through the other limit stop in the

process.

Feed the rst link of the chain into the tensioner on the

‘electric end with cord.’ Turn the electric end by 90° to

lock into posion.

Push the electric end rmly into the end of the C-rail unl

its ange meets edge of the rail. Loosen the screw on

limit stop “H” and slide against the tensioner.

90°

XNote: the ‘electric end’ that ships in the assembly is not

used and may be discarded.

Assembly

At the other end of the C-rail assembly:

Disassemble tensioner, tensioning bolt, and spring from

the ‘non electric end’. Slide tensioner onto chain and

rotate 90° to lock.

Slide the ‘non-electric end’ into the end of the rail,

guiding the tensioner into the hole in the end. Seat the

end fully onto the end of the rail using rm pressure.

Thread the spring onto the tensioning bolt and screw into

the tensioner by hand.

Using a socket wrench, ghten the tensioning bolt unl

the collar under the bolt head aligns with the arrow

marking on the non-electric end.

At the other end of the rail (electric end):

Do not adjust the factory posion of the tension bolt in

the embedded tensioner. Doing so could cause damage

to the tensioner.

90°

Assembly

Lock the carriage into place by pulling once on the release

cord, then sliding the carriage one direcon. There will be

an audible ‘click’ and the carriage will freeze its posion.

Insert two M8 x 25mm carriage bolts into rail mid-

aachment bracket as shown. Slide onto one end of the

rail, leaving at about the 1/3 posion. Repeat for the

opposite end of the rail.

Aach the angle brackets through the uppermost hole

with lock washer and nut. Repeat for other rail mid-

bracket.

Assembly

FOR CEILING MOUNTED APPLICATIONS:

Aach boomerang curved brace onto carriage as shown.

With thick washer and medium length pin and clip.

Posion end bracket on assembly as shown at le. Thread

long pin into end, then x into place with two clips.

Repeat for other end of rail assembly.

CEILING MOUNTED, CONTINUED

Aach U-ng with short pin and clip as shown.

Assembly

WALL (SIDE) MOUNTED, CONTINUED:

Slide boomerang curved brace into U-ng assembly and

ax with short length pin and clip. The secon of the

brace with 3 holes should be running parallel to the track.

Aach the other U-ng to the other end of the brace

with another short pin and clip.

FOR WALL (SIDE) MOUNTED APPLICATIONS:

Aach the U-ng with long stud and collar to carriage

as shown.

Installation

Plan your layout: The ‘closing’ end of the rail assembly should

be set back from the closed door by 1/2” minimum. The door

may be mounted on the exterior or the interior.

Aach rail assembly to wall or ceiling with 5/16” lag screws.

Note: Aachment must be to adequate framing or strapping.

Drywall aachment only is not permied. The track must not

come into contact with the door’s supporng sliding track at

any me. Curved brace may be rotated for maximum

exibility. Ceiling mounted clearance shown is from ceiling

plane to centerline of U-ng. Wall mounted clearance is

from boom of track to U-ng.

1/2” MIN

4” to 7” 4” to 7”

Installation

Posion door bracket in desired locaon. Nong the

clearances on previous page, swivel boomerang brace and

U-ng assembly to determine best placement. Mark the

locaon of the brace’s two mounng holes.

Cut door bracket to length (if desired). Plug end with plasc

end cap provided and install on door with 5/16” x 1-1/2”

lag bolts. Predrill through the bracket where the U-ng

meets it. Fasten securely with M10 x 40mm bolt.

Table des matières

Manuels ouvre-porte de garage populaires d'autres marques

Dorma

Dorma ES 90 Manuel utilisateur

Garaga

Garaga SECURITY+ 3265GCM 1HP Manuel utilisateur

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manuel utilisateur

Chase Doors

Chase Doors DuraShield Manuel utilisateur

CSI

CSI Classic Manuel utilisateur

HATO

HATO 120 Manuel utilisateur

Chamberlain

Chamberlain Elite 3575S Manuel utilisateur

Richmond

Richmond GTR156 Manuel utilisateur

Raynor

Raynor 1280RGD Manuel utilisateur

CAME

CAME F4000 Series Manuel utilisateur

B&D

B&D Controll-A-Door 5 Manuel utilisateur

BFT

BFT PRV AA SL Manuel utilisateur

Craftsman

Craftsman 139.53924 Manuel utilisateur

Chamberlain

Chamberlain MyQ 940ESTD Manuel utilisateur

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Manuel utilisateur

Westfalia

Westfalia 19 36 07 Manuel utilisateur

Chamberlain

Chamberlain HD520EVP Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur