Edge-Core ECWO5210-L Manuel utilisateur
ECWO5210-L
Outdoor Access Point
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
1
FCC CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
※FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the
potential for harmful interference to co-channel Mobile Satellite systems.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
2
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Model: ECWO5210-L
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and
hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.
• Radio: EN 300.328:
• Radio: EN 50392
• EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022Class B, EN 55024:+ A1 + A2including the followings:
EN 61000-3-2, EN 61000-3-3.
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by Edgecore Networks Corporation. The use of software or firmware not provided
and supported by Edgecore Networks Corporation. may result in the equipment no longer being
compliant with the regulatory requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be
restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory
authority for compliance.
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
3
Preface
Package Contents
The ECWO5210-L is a rugged multi-mode,
high-end dual radio 802.11 b/g/n + ac MIMO Access
Point (AP), specifically designed for building
municipal or campus wide wireless networks in
harsh outdoor environments. There are two system
modes that can be used for dual purposes. It can be
deployed as a traditional multi-wireless Access
Point (AP) or a Relay. The ECWO5210-L access
points make wireless communication fast, secure
and easy.
The die-cast Aluminum sealed ECWO5210-L is
rust-free and IP68 compliant. It is high wind load
resilient and is designed to operate in a wide range
of temperature. Flexible deployment with a variety
of antennas allows ECWO5210-L to easily serve
clients located in different directions as well as for
coverage extension.
This Quick Installation Guide (including FAQ
Instruction Guide) provides instructions for getting
started with the ECWO5210-L.
1. Edgecore ECWO5210-L x 1
2. Quick Installation Guide (QIG) x 1
3. Mounting Kit x 1
4. Ground Cable x 1
5. Waterproof M12 Connector Pack x 1
6. Waterproof RJ45 Connector Pack x 2
It is recommended to keep the original
packing material for possible future shipment
when repair or maintenance is required. Any
returned product should be packed in its
original packaging to prevent damage during
delivery.
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
4
System Overview
ECWO5210-L
Top
Back
N-type Connector x 4
For connecting to an antenna (RF CardA x 2, RF Card B x 2)
Connector marked –1 is for the primary antenna when theAP is not in 802.11n
or 802.11ac mode. Utilize all connectors for optimized MIMO performance.
Ground Connector
For connecting the ground wire
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
5
Bottom
1
M12 DC Connector
DC input (12V) is supported on ECWO5210-L
2
Ventilation Valve
Due to extreme weather conditions, water vapor in the ECWO5210-L may
condense. The valve allows ventilation to prevent moisture buildup within
the ECWO5210-L.
3
Uplink (PoE Connector)
For connecting to the Power Sourcing Equipment (PSE)
4
Ethernet LAN
Attach Ethernet cables here for connecting to the wired local network
5
Console
The system can be configured via a serial console port. The administrator
can use a terminal emulation program such as Microsoft’s Hyper Terminal
for troubleshooting purposes.
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
6
Hardware Installation
The following are the basic installation steps which can be used for testing and configuring the ECWO5210-L.
Installation Steps:
Step 1. Connect an antenna to the connector.
Step 2. Connect the Ethernet Port of ECWO5210-L to the POWER & DATA OUT Port of the PSE.
Step 3. Connect one end of an Ethernet cable to the Data Port of PSE and the other end to the computer.
Step 4. Power on the PSE in order to supply power to the ECWO5210-L.
Installing the Waterproof Connection Pack:
A connector pack as shown in the figure below is included with the system.
Parts Included: 5 Parts –Part-A ~ Part-E
Step 1. Take the white sticker off Part E and attach it to Part-D.
Step 2. Plug Part-C into Part-D. There will be three main parts as shown below.
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
7
Step 3. Insert the cable through the main parts and install a RJ-45 connector using straight-through method
(both ends are in the same wiring order: 1 (Tx+), 2 (Tx-), 3 (Rx+), 6 (Rx-)).
Example after the RJ-45 connector is installed,
Step 4. Plug the RJ-45 Connector into the system and make sure the locking ring is locked in well.
Step 5. Coil waterproof tape to secure the parts of the Waterproof Connector Pack.
Straight-Through Cable Wiring
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
8
Installing the Waterproof Connection Pack (Optional):
The M12 Waterproof Connector Pack is used for DC power supply, and it consists of 5 parts:
Step 1. Pass power cable through the Sealing Nut, Gaskets, and Clamp Ring (items 2-5)
Step 2. Solder power pins with reference to the pin definition below
Pin Number
Pin Definition
1
V+
3
V–
4
NC
Quick Installation Guide
ECWO5210-L Outdoor Access Point ENGLISH
9
Step 3. Seal all connectors and fasten sealing nuts
Now, the Hardware Installation is complete.
Table des matières
Autres manuels Edge-Core Point d'accès sans fil
Edge-Core
Edge-Core ECW7220-L Manuel utilisateur
Edge-Core
Edge-Core ECW5320 Manuel de programmation
Edge-Core
Edge-Core ECWO5211-L Manuel utilisateur
Edge-Core
Edge-Core OAP6626A Manuel utilisateur
Edge-Core
Edge-Core ECWO3320-L Manuel utilisateur
Edge-Core
Edge-Core ECWO4320 Manuel utilisateur
Edge-Core
Edge-Core ECW5110-L Manuel utilisateur
Edge-Core
Edge-Core WA4101-Cradle Manuel utilisateur
Edge-Core
Edge-Core ECW5410-L Manuel utilisateur
Edge-Core
Edge-Core ECWO5213-L Manuel utilisateur
Edge-Core
Edge-Core ECW100 Manuel utilisateur
Edge-Core
Edge-Core ECWO3220 Manuel de programmation
Edge-Core
Edge-Core ECW7212-L Manuel utilisateur
Edge-Core
Edge-Core ECW5211-L Manuel utilisateur
Edge-Core
Edge-Core OAP101 Manuel utilisateur
Edge-Core
Edge-Core ECWO5212-L Manuel utilisateur
Edge-Core
Edge-Core ECW7210-L Manuel utilisateur
Edge-Core
Edge-Core EAP104 Manuel utilisateur
Edge-Core
Edge-Core ECW5210-L Manuel utilisateur
Edge-Core
Edge-Core EAP101 Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
