EdenPURE A5955 Manuel utilisateur
Classic Heater
• 1500 Watts with
Two Heat Settings
• Thermal Shut-off Protection
• Tip-Over Switch
• Room Temperature
LED Display
• Precision Temperature
Control
• Easy Push-Button Controls
• Remote Control
• Advanced Dual Heating System (ADHS)
Owner’s Manual
PLEASE READ AND
SAVE THESE INSTRUCTIONS
Model No.: A5955
CONGRATULATIONS!
The Classic Heater you have just purchased is a safe and powerful heater,
designed to heat a room after a few minutes of operation. The far-infrared
Quartz-PTC heating system is an excellent choice for safely heating whole
rooms, while saving on heating costs.
Additionally, this heater includes an overheat protection system and an inlet air
overheat protection system designed to ensure your safety.
This heater does not reduce humidity or oxygen in your home or office,
promoting a healthier environment!
Before using your Classic Heater, please take a few minutes to read these
instructions, and review the product’s limited warranty.
Thank you!
CAUTION- High temperature! Keep electrical cords, drapery, and other
furnishings at least 3 feet (0.9 m) from the front and rear of the heater.
IMPORTANT
INSTRUCTIONS
When using this appliance, basic precautions should always be followed to
reduce the risk of fire, electric shock and injury to persons.
1. Read all the instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes and curtains at least 3 feet (0.9 m) from the front of the
heater and away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children
or persons with physical challenges and whenever the heater is left
operating and unattended.
WARNING! To reduce the risk of fire, electric shock, or personal injury, read
all the instructions before using this heater. This appliance is intended for
household or personal use only as described in this manual. Any other use
including but not limited to commercial, agricultural, or outdoor use, is not
recommended by the manufacturer and may cause fire, electric shock, injury
and/or damages. The use of any attachments and accessories or extension
cords not recommended or sold by EdenPURE® may cause hazards and void
the warranty.
4. Do not operate the heater with a damaged cord or plug, or after the heater
malfunctions, has been dropped, or damaged in any manner. Return the
heater to an authorized service facility for examination, electrical or
mechanical adjustment, or repair.
5. Do not use outdoors.
6. This heater is not intended for use in bathrooms, laundry areas or similar
locations. Never locate the unit where it may fall into a bathtub or other
water container.
7. Do not run the cord under carpeting and do not cover the cord with throw
rugs, runners or the like. Do not route cord under furniture or appliances.
Arrange the cord away from traffic areas to avoid a tripping hazard.
8. To disconnect the heater, turn controls to OFF, then remove the plug from
outlet.
9. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock, fire or damage to the heater.
10. Connect to properly grounded outlets only.
11. To prevent a possible fire, do not block air intakes or exhaust openings in
any manner. Do not use on soft surfaces, like a bed, where openings may
become blocked. Use the heater on flat, dry surfaces only.
12. A heater has hot and arcing or sparking parts inside. Do not use the heater
in areas where gasoline, paint or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or injury
to persons.
14. Never clean this heater while it is plugged in. Do not immerse in water. To
disconnect, turn control to OFF, then remove the plug from the outlet by
grasping it and pulling it from the outlet. Never yank on the cord.
15. Always unplug the heater when it is not in use.
16. Always plug heater directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
17. It is normal for the heater’s plug and cord to feel warm to the touch. A plug
or cord which becomes hot to the touch or becomes distorted in shape may
be a result of a worn electrical outlet. Worn outlets or receptacles should be
replaced prior to further use of the heater. Plugging this heater into a worn
outlet may result in overheating of the power cord or fire.
18. Make sure the plug is fully inserted into an appropriate receptacle. Be
mindful that receptacles also deteriorate due to aging and continuous use.
Check periodically for signs of overheating or deformations of the plug. If
any overheating or deformation occurs, immediately discontinue using the
heater and contact an EdenPURE® Authorized Service Center.
19. CHECK YOUR HEATER CORD AND PLUG CONNECTIONS. Faulty wall
outlet connections or loose plugs can cause the outlets or plug to overheat.
During use, please check frequently to determine if your plug outlet or
faceplate is HOT! If it is hot, discontinue using the heater and/or make
certain a qualified electrician checks and replaces the faulty outlet(s).
CAUTION: This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Product Specifications
Voltage Rating
120V (60Hz)
Power Consumption
1500W
Unit Size
12.1 in. (H) X 9.4 in. (W) X9.4 in. (D)
Unit Weight
9.7 lbs.
G
B
TM
Special Features
LED Display – When the unit is plugged in and the Mode Button pressed, the
LED display will show the room temperature. At ECO mode, it will display the set
value 2 minutes after the desired temperature is set.
Overheat Cut-Off Protection System –This heater includes a protection system
that shuts off the unit if it overheats for any reason.
Inlet Air Overheat Protection System – This heater will automatically shut off if
the inlet air duct becomes obstructed and causes the unit to overheat.
Safety Tip-Over Switch – The Classic Heater is designed to shut off
automatically when tipped in any direction. Place the heater on a flat, smooth,
stable surface to prevent the heater from tipping over again. When returned to
a normal upright position, the heater is ready for use again. This is a safety
feature to avoid the possibility of fire should the unit be tipped accidentally.
Advanced Dual Heating System (ADHS) - EdenPURE® is the first to feature a
dual heating system for maximum heat transfer rate. It combines the energy
efficiency of infrared heat with the comfort of convection heat to heat your room
fast and comfortably—without hot spots and cold spots.
Features
A. “Cool-Touch” cabinet E.
LED temperature display
B. POWER LED light F.
Increase temperature button
C. Standby ON/OFF button G. Decrease temperature button
D. MODE button
F
E
D
A
C
Operating Instructions
1. Plug the power supply cord into a grounded wall outlet. (120VAC,
60Hz)
Important: This heater is for use on
120 volts. This heater comes with a
grounded (three-prong) plug. The
grounded plug must be used with a
grounded outlet. Do not use an
adapter in a two-slot wall outlet.
2. TURNING THE HEATER ON
To turn the heater ON, press the MODE button, the heater will wait in ECO
Mode.
3. HEATING MODES
Press the MODE button to toggle between the different modes: ECO, HIGH,
LOW and STANDBY. Heater exit from any mode to standby mode by
pressing the STANDBY button.
4. ECO MODE – 1500W/1000W
ECO mode is a computerized mode to optimize energy efficiency. It will
programmatically select between HIGH and LOW power mode to heat up
the room to the desired temperature in the most effective way. Once the
desired temperature is achieved, the heater will maintain the room to the set
temperature. ECO mode is the environmental friendly operating mode.
5. HIGH POWER MODE – 1500W
HIGH mode will control the heater to operate at high power until the room
reached the set temperature. The heater will stop heating and initiate
component cooling process before turning off the fan. Once the desired
temperature is achieved, the heater will maintain the room to the set
temperature.
6. LOW POWER MODE – 1000W
LOW mode will control the heater to operate at low power until the room
reached the set temperature. The heater will stop heating and initiate
component cooling process before turning off the fan. Once the desired
temperature is achieved, the heater will maintain the room to the set
temperature.
7. SETTING THE TEMPERATURE
Choose the desired Mode: ECO, HIGH, or LOW. To set the desired
temperature:
Press the
button once
until the numeric temperature starts flashing.
Press the button again to increase the temperature or the button to
decrease the temperature.
Once the temperature is set, the heater will warm up the room using the selected
Mode. The heater will sample the room temperature every 4 minutes after the
desired temperature is reached.
8. Display the room temperature
The display shows the set temperature all the time, press and hold the
MODE button and then press the button. The room temperature will
display for 30 seconds. It will return to set temperature after 30 seconds.
Remote Control
Before Use
Battery has been installed in the remote control.
Before use please unplug the transparent plastic
sheet which was inserted in the remote control.
NOTE: Remove the battery if the remote control is
not to be used for a month or more. Battery left in
the unit may leak and cause damage.
Instructions for the Use of the IR Remote
Control
The buttons on the remote control functions in the same manner as those on
the control panel on the front of the heater. Set the timer by using the remote
control.
Setting the Timer
1. Press the TIMER button until Set Time starts flashing. The default value is 3
hours.
2. Press the button to increase the set time or the button to decrease
the set time. The timer can be set from
1 to 12 hours. The timer will set and
execute after the LED display stops flashing. The heater will shut OFF
automatically when the set time is reached.
3. To turn the timer OFF, follow step 1,
pressing the
button to set the
time to 0. The timer feature will turn off when the LED stops flashing.
Maintenance
1. Always turn the heater OFF and disconnect the cord from the electrical
outlet before cleaning the unit.
2. Light accumulation of dust may be removed from the heater with a soft cloth
or vacuum cleaner.
3. Wipe the exterior surfaces of the heater occasionally with a damp cloth (not
dripping wet), using a solution of mild detergent and water. Dry the case
thoroughly before operating the heater.
Caution! Do not allow water to run into the interior of the heater as this could
create a fire or electric shock hazard.
4. The fan motor is factory-lubricated for life and will require no further
lubrication.
5. Store the heater in a clean, dry place when it is not in use.
Cleaning the electrostatic filter
The heater has an electrostatic filter located at the rear. The cleaning of the
filter should be performed once per month or as needed (when dust is visible
on the filter) to ensure efficient operation of the heater.
1. Power the heater OFF by pressing the POWER button located on the left
side of the Control Panel.
2. Unplug the heater’s power cord.
3. Turn the stopper 90⁰ clockwise/counterclockwise. (Figure 1).
4. Remove the filter by pulling down and out (Figure 2).
5. Clean the filter by vacuuming.
6. Replace the filter by sliding the filter into the gap.
Warning: Any other servicing needed must be performed by an authorized
service representative. Do not attempt to service the unit yourself.
Product Specifications
Model No.: A5955
Voltage: 120V, 60Hz
Current: Maximum continuous draw:
12.5 amps
Output: 5200 BTUs
Power: 1500 Watts
Blower: Multi-blade; Low Noise, High Pressure
In The Box
• DR Infrared Portable Space Heater
• Feet (4 pcs)
• Remote Control (1 battery)
• User’s Manual
Figure 2
Figure 1
•
Quick Start Guide
Table des matières
Autres manuels EdenPURE Chauffage
EdenPURE
EdenPURE US1000 Manuel utilisateur
EdenPURE
EdenPURE TrustedCOMFORT Manuel utilisateur
EdenPURE
EdenPURE Quartz Infrared Portable Heater Guide d'installation
EdenPURE
EdenPURE Signature Guide d'installation
EdenPURE
EdenPURE GEN21 Guide d'installation
EdenPURE
EdenPURE A5986 Manuel utilisateur
EdenPURE
EdenPURE 360 Super climater Guide d'installation
EdenPURE
EdenPURE HEA-900 Manuel utilisateur
EdenPURE
EdenPURE GEN3 500 Guide d'installation
EdenPURE
EdenPURE Classic A5275-SPI Manuel utilisateur
EdenPURE
EdenPURE usa 1000 Manuel utilisateur
EdenPURE
EdenPURE SunTwin 1000XL Guide d'installation
EdenPURE
EdenPURE 500-XL Guide d'installation
EdenPURE
EdenPURE Classic CopperPLUS A5946 Manuel utilisateur
EdenPURE
EdenPURE Personal model Guide d'installation
EdenPURE
EdenPURE GEN2 Guide d'installation
EdenPURE
EdenPURE A5893 Manuel utilisateur
EdenPURE
EdenPURE Signature Guide d'installation
EdenPURE
EdenPURE US1000 Guide d'installation
EdenPURE
EdenPURE A5934 Manuel utilisateur
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
Empire Heating Systems
Empire Heating Systems WCC65 Manuel utilisateur
Wetekom
Wetekom 92 86 43 Manuel utilisateur
Desa
Desa SPC170-F Manuel utilisateur
Watlow
Watlow Watrod Electric Tubular Heaters Manuel utilisateur
Haverland
Haverland ECO-DRY GPS Series Manuel de la liste des pièces
Stelpro
Stelpro ASILVC2060 Series Manuel utilisateur