Edelbrock 6510 Manuel utilisateur

Rev. 4/27/00 Catalog #6510

Page 1of 2

EDELBROCK HEADER - CATALOG #6510

for 1996-1999 Pick-Up, 5.0L, 5.7L V8 CPI without A.I.R. &

1996-1999 Suburban, Blazer, Tahoe, Jimmy, Yukon, 5.0L,

5.7L CPI without A.I.R.

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before installing your Headers. If you have any questions or problems, please

call our Technical Hotline at: 1-800-416-8628 from 7:00 am - 5:00 pm, Monday-Friday, Pacific Standard Time or e-

mail us at [email protected]. Please fill out and mail your warranty card.

HEADERS: These components are designed to improve the exhaust efficiency of the GM C.P.I. (Central Port Injection) V8

engine. ThissystemdoesnotrequireweldingforinstallationandretainsallO.E.M.emissionsequipment. TheseEdelbrock

headers are street legal in all 50 states.

SUGGESTED TOOLS FOR INSTALLATION: This vehicle has metric fasteners.

❑3/8" ratchet socket set with extensions and universal 13mm and 15mm swivel sockets

❑Combination set of open-end wrenches

❑Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695)

SPECIAL NOTICE: This Edelbrock part has received an Executive Order (E.O. #) from the California Air Resources Board

(C.A.R.B.)makingitlegalforstreet use on pollution-controlled motor vehicles in all 50 states. To assistyouwithemissions

equipment certification, we have included a silver fan shroud decal to help testing personnel verify that this part is a legal

replacement part on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your fan shroud

next to the existing emission and engine specification decal. Do not cover your original equipment specification decal with

the Edelbrock fan shroud decal.

WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your

headers. Those products can cause excessive heat and moisture buildup resulting in corrosion and early

failure of the system.

NOTE: High temperature spark plug wires and boots are recommended to withstand heat from Headers.

DISASSEMBLY

1. Disconnect negative battery cable.

2. Raise vehicle and disconnect 02 sensors.

3. Unbolt stock exhaust pipes from manifolds.

Right Side

1. Remove air intake assembly.

2. Disconnect spark plug wires from spark plugs.

3. Unbolt dip stick tube.

4. Unbolt and remove manifold.

5. Install flange gasket and header from top. Install

header bolts, lock washers, and thick flat washers

supplied, ensure proper alignment and tighten

bolts.

NOTE: Thick washers are to be used on slotted

holes of port flange.

6. Re-install spark plug wires.

7. Re-fasten dip stick tube using spacer and bolt

supplied in kit (if needed).

8. Re-install air intake assembly.

9. With wire ties, route any hoses, wires or lines away

from headers as necessary.

Rev. 4/27/00 Catalog #6510

Page 2of 2

Left Side

1. Disconnect spark plug wires from spark plugs.

2. Disconnect E.G.R. tube from rear of manifold.

(Stock E.G.R. adapter fitting will be re-used.)

3. Disconnect temperature sensor wire.

4. Unbolt and remove manifold from top side.

5. Install flange gasket and one 3/8"-16 x 1" bolt,

lock washer, and flat washer at rearmost bolt

hole (leave bolt loose enough to accept Header).

6. Install left side Header from top side.

7. Install all bolts and washers on left side (do not

tighten at this time).

NOTE: Thick washers are to be used on slotted

holes of port flange.

8. Re-install E.G.R. tube to header using stock

adapter.

9. Align all parts and tighten left side flange bolts at

this time.

10. Re-install spark plug wires.

11. Re-install temperature sensor wire to

temperature sensor.

ASSEMBLY OF EXHAUST PIPE

1. Usingsuppliedhardware and new donut gaskets

on both sides, re-attach the factory extension

pipes to the headers, and tighten bolts evenly to

ensure a tight seal.

2. Re-connect O2 sensors. Route O2 sensor wire

from loom to O2 sensors away from exhaust

components.

FINAL INSPECTION

1. Check all lines (hydraulic, vacuum, air

conditioning and fuel) to ensure there is

adequate clearance to headers.

2. Re-connect battery.

3. At this point, it is a good idea to look everything

over and make sure that nothing was missed in

assembly.

4. Start vehicle and bring up to normal operating

temperature. Check for possible leaks.

5. Turn engine off and let cool. Tighten all bolts

again.

HARDWARE SUPPLIED

Qty. Description Qty. Description

❑1#25-9157 Header left side ❑63/8” Flat washers

❑1#25-9158 Header right side ❑11/4 Hex capscrew

❑12 Hex header bolts ❑4Hardened washers (for header flange slotted holes)

❑2Port gaskets ❑63/8” Hex nuts

❑2Donut gaskets ❑13/8” O.D. spacer

❑63/8” Hex capscrews ❑3Wire ties

❑18 3/8” Lock washers

Edelbrock Corporation

2700 California St.

Torrance, CA 90503

Tech Line: (800) 416-8628

Office: (310) 781-2222

E-Mail: [email protected]

Table des matières

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 2934 Manuel utilisateur

Edelbrock

Edelbrock PERFORMER RPM 60549* Manuel utilisateur

Edelbrock

Edelbrock Performer Multipoint 3501 Document technique

Edelbrock

Edelbrock SBC Vortec 283-400 c.i.d. Chevy V8 Manuel utilisateur

Edelbrock

Edelbrock 70003 Manuel utilisateur

Edelbrock

Edelbrock 70402 Manuel utilisateur

Edelbrock

Edelbrock 9629 Manuel utilisateur

Edelbrock

Edelbrock 36011 Manuel utilisateur

Edelbrock

Edelbrock Honda XR400 Manuel du propriétaire

Edelbrock

Edelbrock 5734 Manuel utilisateur

Edelbrock

Edelbrock 5785 Manuel utilisateur

Edelbrock

Edelbrock 70404 Manuel utilisateur

Edelbrock

Edelbrock 1465 Manuel utilisateur

Edelbrock

Edelbrock Fe Ford 5771 Manuel utilisateur

Edelbrock

Edelbrock 4462 Manuel

Edelbrock

Edelbrock Performer 70070 Manuel utilisateur

Edelbrock

Edelbrock 6700 Manuel utilisateur

Edelbrock

Edelbrock 3811 Manuel utilisateur

Edelbrock

Edelbrock 2010 Manuel utilisateur

Edelbrock

Edelbrock 60509 Manuel utilisateur

Edelbrock

Edelbrock Performer 60039 Manuel utilisateur

Edelbrock

Edelbrock Victor Jr. 70057 Manuel utilisateur

Edelbrock

Edelbrock 67362 Manuel utilisateur

Edelbrock

Edelbrock 63-0342 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur