Edelbrock 5670 Manuel utilisateur

Brochure #63-0489 Page 1 of 2

Catalog #5670

Rev. 1/06 - DA/mc

EDELBROCK CAT-BACK EXHAUST SYSTEM

for 1994-1996 Impala SS with 5.7L V8 Engine

Catalog #5670

INSTALLATION INSTRUCTIONS

Application: Designed for 1994-1996 Impala SS with 5.7L V8 Engine.

Suggested Tools for Installation:

❑3/8” rachet set and metric sockets ❑15mm wrench

❑Jackstands and jack ❑Liquid penetrant and rubber lubricant

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Disassembly

1. Raise vehicle and support with the proper jackstands,

leaving the rear suspension hanging.

2. Use caution around hot exhaust systems to avoid

burns.

3. Use penetrating oil on all nuts, bolts and rubber

hangers.

4. If you are using a lift or jackstands, the old system can

be removed in one piece. Remove the nuts to the

catalytic converter pipes and remove the old muffler

assembly.

5. Remove the stock hangers behind the stock mufflers.

Assembly

1. Install supplied rear muffler hangers using stock

muffler hanger holes.

2. Install the left and right I-pipes to catalytic converter

and snug bolts (do not tighten at this time). Slip

mufflers onto I-pipe. Slip 2-1/2” band clamps on and

snug bolts.

Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions,

please contact our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday through Friday, Pacific

Standard Time or e-mail us at [email protected]. Please fill out and mail your warranty card.

WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!

3. Install I-pipe bracket in factory location (on left side

transmission mount). The two mounting bolts are

slotted to help you align exhaust system. Do not

tighten at this time.

4. Slip a 2-1/2” U-clamp onto left I-pipe and snug pipe to

bracket installed in Step 2.

5. Slip the 2-1/2” U-clamps over the muffler outlets.

Install the overaxle pipe into the mufflers, slip on 2-

1/2” U-clamps and let hang on hangers.

6. Slip band clamps onto tailpie inlet end, then slip

tailpipes onto overaxle pipes. Engage hangers on

tailpipes into stock isolators.

7. Using band clamps, install tailpipe tips onto outlet of

tailpipe and snug clamps.

8. Align system to clear frame, heat shields, suspension,

etc., and tighten working from front to rear of vehicle.

NOTE: Bumper height may vary by as much as 1/2” on

different vehicles, so you may need to bend the rear

hanger to adjust for your vehicle.

9. Check for leaks and correct as needed.

KIT CONTENTS

Catalog #5670

Qty. Part # Description

1 25-3100 I-Pipe Assembly (left)

1 25-3101 I-Pipe Assembly (right)

1 25-3102 Overaxle Pipe Assembly (left)

1 25-3103 Overaxle Pipe Assembly (right)

1 25-3104 Tailpipe Assembly (left)

1 25-3105 Tailpipe Assembly (right)

2 25-3236 Tailpipe Tips (SS)

2 25-5510 SDT Muffler

2 33-8001 Hangers

2 46-1076 Flange

1 23-1726 I-Pipe Bracket

3 46-5185 2-1/2” U-Clamps

6 46-6611 2-1/2” Band Clamps

Band Clamp

U-Clamp

Band Clamp

Right I-Pipe Assembly

Left I-Pipe Assembly

Band Clamp

Left I-Pipe Bracket

Hanger

SDT Muffler

Assembly

(Left)

SDT Muffler

Assembly

(Right)

Hanger

Flange

Hanger

Left Tailpipe Assembly

Right Tailpipe Assembly

Hanger

WARNING: Support your vehicle with

proper jackstands rated for the total

vehicle weight. Place stands so that

the rear axle is allowed to hang free

for easy system removal.

WARNING: These cat-back systems are

engineered to fit stock catalytic

converters or equivalent replacements.

If you original system has been modified,

Edelbrock will not warranty fit or

performance.

Brochure #63-0489

Catalog #5670

Rev. 1/06 - DA/mc

Page 2 of 2

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 75284 Manuel utilisateur

Edelbrock

Edelbrock 5224 Manuel utilisateur

Edelbrock

Edelbrock 25-9213 Manuel utilisateur

Edelbrock

Edelbrock 72000 Manuel utilisateur

Edelbrock

Edelbrock Victor Jr. 289-302 Manuel utilisateur

Edelbrock

Edelbrock 6876 Manuel utilisateur

Edelbrock

Edelbrock 4803 Manuel utilisateur

Edelbrock

Edelbrock SBC Vortec 283-400 c.i.d. Chevy V8 Manuel utilisateur

Edelbrock

Edelbrock 1100 Manuel utilisateur

Edelbrock

Edelbrock 70028 Manuel utilisateur

Edelbrock

Edelbrock 3862 Manuel utilisateur

Edelbrock

Edelbrock 2162 Manuel d'instructions

Edelbrock

Edelbrock 3886 Manuel utilisateur

Edelbrock

Edelbrock 16211-MBN-640 Manuel du propriétaire

Edelbrock

Edelbrock 1931 Manuel utilisateur

Edelbrock

Edelbrock 65692 Manuel utilisateur

Edelbrock

Edelbrock 65063 Manuel utilisateur

Edelbrock

Edelbrock 72310 Manuel utilisateur

Edelbrock

Edelbrock 6879 Manuel utilisateur

Edelbrock

Edelbrock 47480 Manuel utilisateur

Edelbrock

Edelbrock 1472 Manuel utilisateur

Edelbrock

Edelbrock Torker II 5021 Manuel utilisateur

Edelbrock

Edelbrock 2828 Manuel utilisateur

Edelbrock

Edelbrock 6500 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur