Ecosoft CROSS 90 Guide de l'utilisateur

Installer and user guide for CROSS 90 direct ow

reverse osmosis lter

Інструкція з підключення та експлуатації

прямоточного фільтру зворотного осмосу CROSS 90

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

CONTENTS

1. Purpose of the product 3

2. Specicaons and components 4

2.1 Specicaons and requirements 4

2.2 Water quality 5

2.2.1 Supply water quality requirements 5

2.2.2 Water quality aer lter 5

2.3 Reverse osmosis lter components 6

2.4 Reverse osmosis lter indicators 7

3. Filter installaon 7

3.1 Before commencing installaon 7

3.2 Connecon diagram 8

3.3 Installaon procedure 8

3.4 First me use 13

4. Steps aer installaon 13

5. Usage 14

5.1 Parts of the lter and their recommended change out rates 14

5.2 The procedure for cartridges replacing 14

5.3 Filter lifeme display 15

5.4 Water quality display 16

5.5 System operaon modes 16

5.6 SMART features 17

6. Sanizaon of reverse osmosis lter 18

7. Troubleshoong 20

8. Service record 21

9. Environmental and health safety 22

10. Purchasing 22

11. Transportaon and storage 23

12. Warranty 23

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

DEAR CUSTOMER!

1. PURPOSE OF THE PRODUCT

Thank you for choosing our products.

We want you and your family to enjoy clean drinking water. With Ecoso lter you will forget

the trouble of using large boles. Pure spring water for drinking, cooking and making drinks will

always be at hand. Please read this instrucon manual and check validity of the warranty card

before using the system.

Reverse osmosis is by far the most advanced technology of water puricaon in use today. Special

semipermeable membrane structure similar in its properes to the membrane of a living cell

is capable of purifying drinking water from virtually all harmful impuries (see Figure 1). The

membrane can be conceived of as having ny pores, 200 mes smaller than viruses and 4000

mes smaller than bacteria. Domesc water lters with reverse osmosis membranes harness the

principle of body’s metabolism on a cellular level. Only molecules of certain size can penetrate

cellular membrane.

Direct ow reverse osmosis lter CROSS 90 is a four-stage in three steps ltraon unit with

three cartridges funconing as follows (see secon (2.3) for reference numbers). Filter rack is

connected to cold water supply with feed water adapter (4). White tube (3/8”) carries water from

feed valve through low pressure switch and inlet solenoid valve to the CF lter cartridge. Incoming

water then passes through pre-lter cartridge (7). Pre-lter cartridge is a complex cartridge with

(2) stages inside. It is designed to remove solids (such as rust, sand, silt, etc), residual chlorine,

and organochlorines from water. Aer undergoing pre-treatment steps in the pre-lter, water

enters into the third (and the most important) stage: reverse osmosis membrane (7) contained in

a cartridge RO. One of the two outlets supplies puried water (permeate), and the other carries

away water with rejected impuries (concentrate). The membrane puries water at the molecular

level by passing through its pores only the water molecules and the molecules of dissolved oxygen.

Tap water under

pressure

Figure 1

Molecules of smaller

size, pure water

Larger molecules

Concentrate

for disposal

Membrane

Water

molecules

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

1. PURPOSE OF THE PRODUCT

№ Parameter Value

1Main pressure, bar 1-4 *

2Feed water temperature, °C +5…+30**

3Flow capacity, l/min 1,5

4Electrical rang 230 V, 50 Hz

5Weight of the system, kg 11

6Ambient temperature, °C +5…+40

7Water supply connecon ½″ thread

8Filter dimensions, H × W × D, mm 458 x 140 x 435

2. SPECIFICATIONS AND COMPONENTS

2.1 SPECIFICATIONS AND REQUIREMENTS

Inside the membrane, water is separated into two streams: concentrate, which is discharged into

drain, and permeate, which enters next step – post-lter (7).

Aer opening the puried water valve (3), the pressure in the system drops and the high pressure

switch is acvated, opening the inlet valve and starng the pump, automacally resuming the

ow of water through the pretreatment cartridge to the membrane. Aer opening the puried

water valve (3), the pressure in the system drops and the high pressure switch is acvated,

opening the inlet valve and starng the pump, automacally resuming the ow of water through

the pretreatment cartridge to the membrane. The puried water aer the membrane enters

the fourth stage of puricaon — the CB carbon post-lter, designed for nal water puricaon.

The puried water aer the membrane enters the fourth stage of puricaon — the CB carbon

post-lter, designed for nal water puricaon. It contains extruded acvated carbon. This lter

improves the taste and smell of the puried water. This lter is direct-ow, so no water storage

tank is required. With a capacity of 600 GPD (90 l/h), it takes only 8 seconds to ll a 200 ml glass.

* If supply water pressure is below required value, purchase pumped model or t your exisng

lter with booster pump. If the pressure in the water system is above the limit, it is necessary to

install a pressure regulator on the main pipe. If pressure in tank bladder is outside this range, it is

necessary to pump up or release the pressure unl it conforms to the requirement.

** If supply water temperature is up in the range of +20…+30 °C, rejecon of impuries will be

decreased and system capacity increased, bringing about an increase in TDS. Using the product

with supply water temperature in excess of +30 °C is not recommended.

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

№ Index Value**

1pH 6.5-8.5

2TDS <1500 ppm

3Hardness <500 ppm CaCO3

(<28 °dH)

4Free chlorine <0.5 ppm

5Iron <0.3 ppm

№ Index Value

1pH 5.5-6.5

2TDS 5-15 ppm

3Calcium <2 ppm

4Magnesium <1 ppm

5Sodium + Potassium <5 ppm

№ Index Value**

6Manganese <0.1 ppm

7Chemical oxygen

demand <5 ppm O2

8Total bacterial count

(TBC) <50 CFU/mL

9E. coli ter <3

2. SPECIFICATIONS AND COMPONENTS

2.2 WATER QUALITY

2.2.1 SUPPLY WATER QUALITY REQUIREMENTS*

2.2.2 WATER QUALITY AFTER FILTER*

Do not use with water that is microbiologically unsafe or of unknown quality without adequate

disinfecon before or aer the system.

* If water supply does not meet the requirements, service life of membrane and/or pre-lter

cartridges may be shortened.

** If your home is supplied with raw well water, perform laboratory test of your water before

in- stalling a reverse osmosis lter. If any of your water indices exceed the limit, consider using a

water treatment system to correct supply water quality. Refer to water treatment specialists or

companies for advice and proper equipment selecon.

* Values are determined under the following

condions: temperature of supply water is

25 °C, supply water quality and operaon

condions correspond to manufacturer’s

requirements.

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

2. SPECIFICATIONS AND COMPONENTS

1) Filter rack

4) Feed water

adapter with valve

7) Set of cartridges

CF - CPVDFRO

RO - CSVRO600DFRO

CB - CHVCBDFRO

2) Power adaptor 3) Drinking

water faucet

6) Drain saddle5) Set of colored tubes

2.3 REVERSE OSMOSIS FILTER COMPONENTS

The manufacturer reserves the right

to modify product design or specic

components if such modicaon does

not entail deterioraon of consumer

properes of the product.

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

2. SPECIFICATIONS AND COMPONENTS

3. FILTER INSTALLATION

2.4 REVERSE OSMOSIS FILTER INDICATORS

1 – System performance indicator - making water indicaon, water quality indicaon, faults

indicaon, ushing indicaon

2 – RO replacement lter lifeme indicator

3 – CB replacement lter lifeme indicator

4 – CF replacement lter lifeme indicator

5 – Faucet indicator - making water indicaon, faults indicaon, replacement indicaon, ushing

indicaon

Before installing a domesc reverse osmosis lter please carefully read this instrucon.

This system must be installed in compliance with local codes.

3.1 BEFORE COMMENCING INSTALLATION

1) Check that all parts are in the package. Do not open the plasc bags with lter parts before you

make sure everything is in place to be able to return faulty/incomplete package.

2) Check conformity of your local variables to requirements specicaons:

Main pressure* Supply water temperature*

Check water pressure at mains before install-

ing the product. Compare to the requirements

in paragraph (2.1).

Check temperature of supply water. Compare

to the requirements in paragraph (2.1).

*Refer to paragraph 2.1 for recommended measures in case any of the above variables

does not meet the requirements.

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

— verify that your product is as specied in paragraph 2.1;

— verify that your supply water quality** meets the requirements in paragraph 2.2.

**If supply water quality does not meet the requirements, it is necessary to consult with a

water treatment specialist.

3) Before installing the system, make sure there is enough space for the lter rack under the sink.

4) Electrical safety noce: This appliance should be connected into a circuit with an RCB installed.

Please note voltage requirements.

5) Install the system per the guidelines of this manual.

6) The unit is to be supplied with single-phase 230 VAC, 50 Hz electrical power.

The unit is supplied with power cord and can be connected to a properly installed IEC 60884-1

compliant socket. Electrical specicaon of the unit can be found on manufacturer’s factory

scker. That system and installaon must comply with state and local laws and regulaons.

3.2 СONNECTION DIAGRAM

3.3 INSTALLATION PROCEDURE

Wash your hands thoroughly with an-bacterial soap before handling tubes, cartridges, and

membrane.

This system should desirably be installed in places protected from direct sunlight and away

from heang appliances.

3. FILTER INSTALLATION

3/8” White pipe

1/4” Red pipe

1/4” White pipe

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

1. Remove the reverse osmosis system from its packaging and check the equipment.

2. Shut o water supply in your kitchen or whole home and open water tap where you are about

to install the system (on your kitchen sink) for 1 minute to relieve pressure in the system, and

then close it.

3. Screw the feed water adapter with valve (4) into the cold water plumbing.

Connecons size is selected to t most common size ½ inch pipe. If your pipe is of another size,

prepare an appropriate adapter.

4. Unscrew the compression nut from the feed valve (4) and put it on the 3/8” white tube. Push

the white tube on the end of feed valve’s ng and screw on the compression nut. Connect the

free end of the 3/8” white tube with the quick connect ng “Inlet” on the connecon panel of

the rack. Insert the 3/8“ quick coupling lock plate between the quick connect and the claw of the

water inlet pipe.

3/8” PE pipe in

proper length

3/8” quick coupling

lock plate

3. FILTER INSTALLATION

INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER

5. Connect the drain saddle (6) with drain pipe from

the kitchen sink. The drain saddle is compable

with most standard drain pipes. Drill a hole of 5.0

mm (0.2”) diameter in the kitchen sink drain pipe,

apply rubber gasket with scky base (included in

the package).

Install the drain saddle (6) on the drain pipe over

the hole. Tighten screws on drain saddle with a

screwdriver. Insert red tube into the connecon on

the clamp. Connect the other end of the red tube

with concentrate outlet “Waste” on the connecon

panel of the rack. Insert 1/4” quick coupling lock

plate between quick coupling and jack catch of pipe.

6. Connect one end of 1/4” white tube to

the “Filtered” output on the connecon

panel of the rack. Insert the 1/4”quick

coupling lock plate between the quick

connect and the claw of the water inlet

pipe.

CAUTION! If RO systems do not use air gap faucets, it is required that they be plumbed in with

a physical air gap between the waste water outlet and the drain. This is so if the drain backs

up, sewage will not push up into the RO system.

1/4” quick coupling

lock plate

1/4” wihte PE pipe in proper lenght

Sewage outlet

1/4” quick coupling

lock plate

1/4” wihte PE pipe

in proper lenght

3. FILTER INSTALLATION

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Ecosoft Système de filtration d'eau

Ecosoft

Ecosoft FK1252CEMIXC Manuel utilisateur

Ecosoft

Ecosoft AquaPoint Manuel utilisateur

Ecosoft

Ecosoft FK Series Manuel utilisateur

Ecosoft

Ecosoft RO 5-36 Guide de l'utilisateur

Ecosoft

Ecosoft MO-12 Manuel utilisateur

Ecosoft

Ecosoft 3-STAGE Manuel utilisateur

Ecosoft

Ecosoft WS1 CE Manuel utilisateur

Ecosoft

Ecosoft FPA Series Manuel utilisateur

Ecosoft

Ecosoft Dewberry Manuel utilisateur

Ecosoft

Ecosoft AquaPoint FPV24520ECO Manuel utilisateur

Ecosoft

Ecosoft LUNA Instructions d'installation

Ecosoft

Ecosoft WS1 DV Manuel utilisateur

Ecosoft

Ecosoft FPV12ECO Manuel utilisateur

Ecosoft

Ecosoft Robust Manuel utilisateur

Ecosoft

Ecosoft FU1054TWIN Manuel utilisateur

Ecosoft

Ecosoft FK1252CEMIXA Manuel utilisateur

Ecosoft

Ecosoft FK1035CIMIXP Manuel utilisateur

Ecosoft

Ecosoft MO36000PECO Guide de l'utilisateur

Ecosoft

Ecosoft SENSE Guide de l'utilisateur

Ecosoft

Ecosoft MO6500BWTSS Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur