Ecor-Pro EPD150 Manuel utilisateur

Design

Great British

EPD150

EPD200

EPD150-PRO

EPD200-PRO

DEHUMIDIFIER • DÉSHUMIDIFICATEUR • DESHUMIDIFICADOR

USER MANUAL • MANUEL • MANUEL DE USARIO

For safety reasons, read this information carefully before operating.

Persons who are not familiar with this type of product must not use it.

The dehumidier is safe, however, as with other electrical appliance, use it with care.

The installation must be in accordance with the regulations

of the country where the unit is used.

The unit is designated for indoor operation.

This appliance must be earthed and should only be

connected to an earthed 120V – 60Hz mains supply.

Thank you for choosing this innovative dehumidier.

This manual describes the many benets and advanced features that this unique product has to oer.

This dehumidier is a tough, industrial unit designed to be used almost anywhere that dry air is required.

Desiccant/Absorption dehumidiers are especially suited to applications where low relative humidities are

needed and work well over a wide temperature range.

We specialize in complete indoor humidity control. Our world class products incorporate the latest

technological developments and are designed to create a quality environment.

It is important that you read these instructions carefully before installing and using your new dehumidier.

Please keep them in a safe place for future reference.

THANK YOU! |

SAFETY |

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not clean the dehumidier by spraying it or immersing it in water.

• Do not insert any object into the opening of the dehumidier.

• Disconnect from the mains before cleaning the unit or any of its components.

• Never connect to an electrical outlet using an extension cord. If an outlet is not available, one should be

installed by a licensed electrician.

• Any service other than regular cleaning, setting fan mode or lter replacement should be performed by

an authorized service representative. Failure to do so could result in a loss of warranty. Your dehumidier

is supplied with an electrical cable and an earthed plug. Should it be necessary to replace this plug at any

time, you must use an earthed electrical plug.

Warning! Never operate this appliance if it has a damaged cord or plug.

If the supply cord is damaged an approved service representative or a similar qualied person

must replace it in order to avoid any hazards.

There should be direct access to the electrical plug after connecting the power!

Do not use your dehumidier under the following conditions:

• If the power cable is damaged

• Where the power cable may be easily damaged

• Close to heat source

• Where small children may be left unattended

• Where there is a risk of liquids falling on the unit

• Where it may be damaged by chemicals

This product is not made for DIY repair.

SAFETY (2) |

HOW IT WORKS EPD150/EPD150-PRO|

Your EPD Desiccant dehumidier removes

moisture using a continuously rotating moisture

absorbing wheel —this ‘Desiccant Rotor’ is

literally a honeycomb of extremely hygroscopic

membranes.

A highly ecient yet low noise fan draws air

into the unit (Process Air) and forces it through

a portion of the absorbent rotor. As the air

passes through the rotor, the honeycomb of

hygroscopic membranes absorb almost all

of the moisture creating an extremely dry air

stream.

Most of this air stream is discharged directly

through the ‘Dry Air Outlet’ however, a portion

of this air (Regen Air) is separated and directed

through a heater bank (Regen Heater) where it’s

temperature is raised. This air is then channeled

back through a section of the rotor. As this

air passes back through the membranes, its

higher temperature drives-out the previously

absorbed moisture and discharges it as warm

wet air through the ‘Wet Air Out’ duct.

As the wheel rotates, this process of collecting

and discharging moisture is continuous.

HOW IT WORKS EPD200/EPD200-PRO|

Your EDP Desiccant dehumidier removes

moisture using a continuously rotating moisture

absorbing wheel —this ‘Desiccant Rotor’ is

literally a honeycomb of extremely hygroscopic

membranes.

A highly ecient yet low noise fan draws air

into the unit (Process Air) and forces it through

a portion of the absorbent rotor. As the air

passes through the rotor, the honeycomb of

hygroscopic membranes absorb almost all

of the moisture creating an extremely dry air

stream; this air stream is discharged directly

through the ‘Dry Air Outlet’.

A second fan pushes a separate air stream

(Regen Air) through a heater bank (Regen

Heater) where it’s temperature is raised. This

air is then channeled back through a section

of the rotor. As this air passes back through the

membranes, its higher temperature drives-

out the previously absorbed moisture and

discharges it as warm wet air through the ‘Wet

Air Out’ duct.

As the wheel rotates, this process of collecting

and discharging moisture is continuous.

PATENTED DESICCANT ROTOR

The Desiccant Rotor is the heart of the EPD dehumidier. It is an array of specially

absorbent membranes arranged as a series of corrugations (as shown in the

cut-away image) to give a vast surface area making it an extremely ecient. It is

encased in a galvanized steel ring and turns on high quality sealed ball bearing

units.

REGEN HEATER BANK

The EPD dehumidier uses a ceramic PTC type regen heater. PTC (Positive

Temperature Coecient) heaters are based on a semi-conductor that changes

resistance as it becomes hotter. The semi-conductor is designed so that it’s

resistance rises rapidly at a predesignated temperature, thus it maintains this

temperature across a wide range of operational conditions.

This characteristic means that the heating element can never over heat to

hazardous temperatures, even if the regen airow is completely blocked.

FAN SYSTEM

The EPD dehumidier uses a patented "RadiCal" backward curved fan unit, this is a

highly eective yet quiet system. It is designed to give a good balance of airows

for both ‘Process’ and ‘Regen’ airows.

HOW IT WORKS WORKS (2) |

The EPD dehumidier is designed only for indoor use however, it can be placed inside or outside the room to

be dried.

INTERNAL POSITIONING

When positioning the unit inside the room, place it centrally, ensuring inlet and outlet ducts are clear of

obstruction.

If required, ducts can be connected to the outlet and/or inlet to direct the drying to specic areas.

The Wet-Air-Out MUST be ducted outside the room

EXTERNAL POSITIONING

When positioning the unit outside the room, connect ducting to the outlet to direct the dry air stream into the

room to be dried.

Optionally, the inlet may also be ducted to the room to give a re-circulation eect. In this case however,

because the unit uses a portion for the inlet air for regeneration, provision must be made in the inlet duct to

also draw air form outside the room.

Note:

As the Wet-Air-Out discharge is warm and very humid ensure it is directed where it will have no adverse

eect on the immediate environment.

All ducting lengths should be kept to a minimum —longer lengths will reduce performance.

The Wet-Air-Out is warm and very humid, when a duct is attached, condensation may form on the inside of

the duct. This duct should slope downwards away may from the unit to prevent any condensation running

back into the unit.

POSITIONING|

STAND-ALONE OPERATION

Connect the unit to suitable mains supply.

Ensure Remote Humidistat switch is set in the ‘OFF’ (O) position.

Switch Power switch to the ‘ON’ (I) position.

The fan will start and the Ammeter reading will rise. The ammeter indicates the current taken by the PTC

heater bank. Its reading will depend on the ‘Process’ air temperature and the ‘Regen’ airow. Typically, it will

indicate between 2 and 3 amps (EPD150/EPD150-PRO) or between 4 and 6 amps (EPD200/EPD200-PRO), this

will reduce if the airow is low or the ‘Process’ air temperature is high.

REMOTE OPERATION

For remote operation it is necessary to connect a switch or humidistat via the ‘Remote Humidistat Connector’

which can be accessed by removing the dust cap. A connection plug is available on request.

ATTENTION: The remote connector is mains voltage!

The remote switch/humidistat should be connected between pins 1 and 3.

The earth pin is connected to ground and can be used if required (see wiring diagram).

The Remote Humidistat switch should be set to the ‘ON’ position.

The unit will now operate according to the state of the remote switch.

AIR FILTER

The unit has an inlet air lter, this should be checked periodically and if necessary cleaned. It can be cleaned

with a vacuum cleaner or washed in mild detergent.

ATTENTION:

Do not run the unit without a lter tted as dust will impair the performance of the Desiccant Rotor.

OPERATION|

CONTROLS|

The controls are positioned on the front of the

unit next to the air outlet, they are:

• Power Switch

• Ammeter

• Hour Meter

• Remote Humidistat Switch

• Remote Humidistat Connector

EPD150 EPD150-PRO EPD200 EPD200-PRO

If the dehumidier does not operate:

• Make sure the unit is plugged in.

• Check the fuse

• Check the remote humidistat setting

• Ensure the humidistat (if tted) is turned on

Low Airow:

• Check inlet air lter

• Check inlet/outlets not obstructed

• Check ductwork (if tted) is not obstructed

• Check voltage level

• Check fan is working

If the unit is noisy:

• Check fan operation

• Check rotor drive

• Check for loose screws

Low Dehumidifying Eect:

• Check airows

• Check Amps reading

• Check rotor is turning

Low Amps Reading:

• Check Regen airow

• Check Over-Heat Protector

• Check Heater bank

Rotor Not Turning

• Check belt tension

• Check drive-motor operation

• Check rotor alignment

TROUBLESHOOTING|

OFF

REMOTE HUMIDISTAT

OFF

POWER

A10

OFF

POWER Remote

Humidistat

MAINTENANCE|

ATTENTION

• Maintenance should only be carried out by qualied personnel

• Unit should be disconnected from mains before removing covers

• If unit has just been running, heater bank may still be hot

DESICCANT ROTOR

The desiccant rotor is maintenance free, however, if it becomes blocked with dust (e.g. if it has been running

without inlet air lter) it can be cleaned by vacuum cleaner or low pressure compressed air.

HEATER BANK

The PTC heater bank is maintenance free however, if it becomes blocked with dust (e.g. if it has been running

without inlet air lter) it can be cleaned by vacuum cleaner or low pressure compressed air.

OVER-HEAT PROTECTOR

In the event of total airow loss, the over-heat protector will operate. If this happens

it will need to be manually re-set after the airow is restored.

To reset, push the red button (R) down.

DESICCANT ROTOR DRIVE

The desiccant rotor is driven by a geared motor via a toothed belt. The rotation

speed is approximately 20 RPH. It can be seen turning during operation through

the air outlet duct. If it appears to be slow or sticking, the belt can be re-tensioned

using the 4 mounting screws @ ‘‘A’’.

NOTE: Do NOT over-tension

the belt. After tensioning it

should have movement as

shown in the image.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Ecor-Pro Déshumidificateur

Ecor-Pro

Ecor-Pro LD800 Manuel utilisateur

Ecor-Pro

Ecor-Pro EPD170LGR Manuel utilisateur

Ecor-Pro

Ecor-Pro DH1100 Manuel utilisateur

Ecor-Pro

Ecor-Pro DDH2500 Manuel utilisateur

Ecor-Pro

Ecor-Pro DH8500EW Manuel utilisateur

Ecor-Pro

Ecor-Pro dryfan 8 Manuel utilisateur

Ecor-Pro

Ecor-Pro DH3511 Manuel utilisateur

Ecor-Pro

Ecor-Pro D850E/R410A Manuel utilisateur

Ecor-Pro

Ecor-Pro EPD330LGR Manuel utilisateur

Ecor-Pro

Ecor-Pro EPD50 RESTO Manuel utilisateur

Ecor-Pro

Ecor-Pro dryfan 8 Manuel utilisateur

Ecor-Pro

Ecor-Pro EPD100LGR Manuel utilisateur

Ecor-Pro

Ecor-Pro D950E Manuel utilisateur

Ecor-Pro

Ecor-Pro DDH3500 Manuel utilisateur

Ecor-Pro

Ecor-Pro LD800 Manuel utilisateur

Ecor-Pro

Ecor-Pro DH2500 Manuel utilisateur

Ecor-Pro

Ecor-Pro DH1100 Manuel utilisateur

Ecor-Pro

Ecor-Pro D850E Manuel utilisateur

Ecor-Pro

Ecor-Pro EPHUM24 Manuel utilisateur

Ecor-Pro

Ecor-Pro DRYFAN EPD30 Manuel utilisateur

Manuels Déshumidificateur populaires d'autres marques

Daitsu

Daitsu CD031IU-DFA Manuel utilisateur

Fehom

Fehom PDGT701BE Manuel utilisateur

Hitachi

Hitachi RD-190GX Manuel utilisateur

Westpoint

Westpoint MDF1-30AE Manuel utilisateur

SOLIS

SOLIS easy dry compact Manuel utilisateur

ENVIROBOSS

ENVIROBOSS EB240 Manuel utilisateur

Sinclair

Sinclair R-9112 Manuel utilisateur

Kenmore

Kenmore 580.54701 Manuel utilisateur

Demargo

Demargo DM828NF Manuel utilisateur

Altrad Lescha

Altrad Lescha LDH 600 Manuel utilisateur

BOMANN

BOMANN LE 1150 CB Manuel utilisateur

SPT

SPT SD-46 Manuel utilisateur

REMKO

REMKO SLN 40 Manuel utilisateur

Haier

Haier HD458 Manuel utilisateur

Logik

Logik L20DHW12 Manuel utilisateur

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Guide de démarrage rapide

Blitz

Blitz HHD Series Manuel utilisateur

Prem-I-Air

Prem-I-Air PD14DEN Manuel utilisateur