ECOheat ES808 Manuel utilisateur

ES808 Passive Infrared (PIR) High Bay Motion Sensor

User Manual

General

The ES808 PIR motion sensor is ideal for high bay applications, such as warehouses

and factories. The sensor has an extruding screw that can easily be installed

directly onto a light fixture.

If, after reviewing this guide, you require additional information or assistance

please contact Eco Heat Equipment at info@ecosensor.co.za, +27 (0)861 999 887,

or www.ecosensor.co.za.

Technical Specifications

§Voltage: 220 – 240V/AC

§Frequency: 50/60Hz

§Load: Incandescent max: 1 000W

Fluorescent max: 600W

LED max: 300W

§Detection Angle: 360 °

§Detection Range: 1 - 8m radius

§Light level: 10 – 2 000 LUX

§Time setting: 10 seconds – 30 minutes

§Installation height: 2.5 - 12m max

§Working temperature: -10°C to 40°C

§Dimensions: Length: 81mm (108.7mm with connector)

Width: 81mm (82.5mm with push button)

Height: 47.9mm

Connector inside diameter: 17.1mm

Connector outside diameter: 20.4mm

Safety

Any incorrect use or installation procedure not recommended by the

manufacturer may cause fire, electrical shock or injury to persons.

Box Contents

Your box should contain the following items:

§Sensor

WARNING:

Controlling a load in excess of the specified ratings will damage the unit and lights

and could pose risk of fire and electric shock.

Do not install this unit to control a power socket.

Installation Instructions

WARNING: ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND

LOCAL ELECTRICAL CODES AND STANDARDS.

Note: motion sensors respond to rapid changes in temperature so care should be

taken not to mount the device near a climate control source (i.e. heaters or air

conditioners). Hot or cold draughts will seem like body motion to the sensor and will

trigger the device. Recommended distance from climate control devices is 2m.

1. Turn power off at circuit breaker or fuse

2. Connect wires as per diagram

3. Sensor can be secured onto light fitting

4. Restore power at circuit breaker or fuse

Sensor calibration:

Note: Allow up to 1 minute for the motion sensor to recalibrate after it has been

connected for the very first time. This is only necessary during installation or when

the mains supply is disconnected.

Installation wire diagram

Operation and Field of View

The motion sensor detects motion within its coverage area and controls the

associated lighting connected to the sensor. The passive infra red (PIR) sensor is

sensitive to the heat emitted by the human body. In order to trigger the sensor the

source of heat must move from one zone of detection to another. The device is

most effective in sensing motion across its field of view and less effective sensing

motion towards or away from its field of view.

Sensor detection range from side: large motion

Sensor detection range from top: large motion

Motion Sensor Settings and Adjustments

The motion sensor is a Passive Infra Red (PIR) type electronic occupancy detector,

which in turn switches the lights when connected to the motion sensor. There are

three adjustments that can be made to influence the operation of the motion

sensor:

1. RANGE: motion detection range

2. TIME: time delay after motion/sound until shut off

3. LUX/LIGHT: level of ambient light sensitivity

The three adjustments settings are as follows:

Detection range: 1m to 8m radius

Time setting range: 10 sec to 30 min

Lux (light) sensitivity: 10 to 2 000 LUX

Manual Override

For manual control, the ES808 motion sensor features a convenient push button

switch.

If the lights are OFF, pressing the button will turn the lights ON for as long as the

room is occupied. The lights will turn OFF once the room is vacant, after the

delayed OFF time expires.

If the lights are ON, pressing the button will turn the lights OFF and keep them OFF

even if the room is occupied. This feature is particular useful when the automatic

motion sensor settings need to be overridden. The lights can be turned back ON

by simply pressing the button. The sensor will return to normal operation.

Motion Sensor Adjustments

The motion sensor’s settings can be adjusted as follows:

Step 1 – Adjust the TIME setting to minimum

Turn the TIME control fully anti-clockwise to set to the 10sec testing setting.

Step 2 – Adjust the LUX/LIGHT setting to maximum

Turn the LUX/LIGHT fully clockwise to set to maximum (sensor functioning in all

lighting conditions).

Step 3 – Adjust the RANGE setting

Turn the RANGE control fully anti-clockwise. Move away from the sensor until the

LED stops blinking. This will be the minimum detection range. To lengthen the

range, turn the control clockwise until the desired distance is reached (1m – 8m

maximum).

Step 4 – Adjust the LUX/LIGHT setting

If the LUX/LIGHT control is set to maximum (fully clockwise), the lights will turn ON

whenever the room is occupied, even in full daylight.

Alternatively, turn the LUX/LIGHT anti-clockwise until the desired LUX setting is

achieved.

Step 5 – Adjust the TIME setting

Turn the TIME control clockwise until the desired delay is reached (10sec (testing)

to 30mins).

Factory time out is pre set to 10 seconds.

NOTE: All the time intervals are within approximately 10 seconds of the stated time

out interval.

OTHER CAUTIONS:

Disconnect power when working on electrical outlets or components.

Do not push on the surface of the lens.

Cleaning

Carefully wipe sensor with a soft damp cloth. Do not apply pressure to the lens.

Recycling

Please recycle all packaging material that came with the motion sensor.

Warranty

The sensor has a three (3) year warranty after the date of the original purchase.

Please keep your original receipt, as this will be required for any claims under this

warranty. The warranty is a strictly carry in policy. (The sensor/s has to be returned

to Eco Heat offices for a claim to be processed).

The warranty does not cover:

§damage from misuse,

§neglect or abuse,

§products that have been modified in any way,

§shipping and handling cost associated with the product,

§damage resulting from accidents, lightning, fire, water, power surges,

natural disasters and/or incorrect installation

For more information, view the Return/Refund Policy at www.ecosensor.co.za.

Optional Remote Control

The sensor LED will flash 3 times to

confirm each setting applied

ON=Always on. After about

six hours turns to “AUTO”

mode.

OFF=Always off. After about

six hours turns to “AUTO”

mode.

Automatic ON/OFF

Test mode: Light level will not

influence the operation in this

mode. Use to test and setup

detection range.

Reset: Resetting of all

functions to:

Time: 10sec

Range: Max

Lux: Max

Microphone ON/OFF (if

applicable)

Automatic reading and

saving of the actual light

level

Permanent tamper

protection: Lock all settings

to avoid tampering. Only

On and Off buttons will be

functional.

Lux/Light settings (10 to 2000

Lux).

Recommendation: rooms

with daylight 500 Lux, without

daylight 2000 Lux.

Time settings (10 secs to 30

mins)

Range settings (2m to Max)

Trouble Shooting

Malfunction

Possible Cause

Remedy

The unit will

not switch

“on”

a. No mains power

b. No movement is

detected (in detection

zone)

c. Wrong LUX/LIGHT level

setting

d. Electrical circuitry faulty

e. Electrical Installation not

done correctly

f. Unit may be faulty

a. Check mains power is on

b. Move towards the unit (in

detection zone) or increase the

detection range settings

c. Adjust setting on the LUX/LIGHT

settings

d. Refer to the ‘Electrical

Installation’ section to ensure

correct installation

e. Have a certified electrician

disconnect and test the unit

f. Contact Eco Heat Equipment

Unit stays

“on”

permanently

g. Continuous movement in

detection zone

h. The sensor is not

mounted correctly for

reliable operation

i. Wrong LUX/LIGHT level

setting

j. Time setting control is set

too far

k. Unit may be faulty

g. Check detection range setting

and reduce detection range

sensitivity

h. Check detection range setting

and mounting procedure

i. Adjust setting on the LUX/LIGHT

settings

j. Adjust the time setting control

k. Contact Eco Heat Equipment

Due to minor improvements in design or otherwise, the product you purchase

may differ from the one shown in this leaflet. For more information or advice on

this or any other Eco Heat Equipment products, visit www.ecosensor.co.za or

phone +27 (0)861 999 887.

Indemnity: The Author, and supplier, shall not be held liable for any loss, injury or

damage, of whatsoever nature, whether consequential or not, either contractual

sustained to, or caused by, or which may arise through the use of any comments,

suggestions, circuitry, services or equipment offered for purchase. The User,

indemnifies the author and supplier, and agrees not to hold him/her responsible

for any damages, losses and/or liabilities (including legal costs on a scale as

between attorney and user) arising from, or through the use of circuit diagrams,

equipment and services, whether such circuit diagrams, equipment and services

were used with the consent of the User or not. All risks attached to the use of

circuit diagrams, equipment and the connection thereof to the User’s equipment

shall be deemed to have passed onto the User, once having purchased such

equipment from the author or supplier.

OFF

AUTO

TEST

RESET

2000

LUX

500

LUX

10SEC

30MIN

Autres manuels ECOheat Capteur de sécurité

ECOheat

ECOheat ES806 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur