Ecofrost 7950.5115 Manuel utilisateur

(HC-Gas R600a Used)

Refrigerated Counter Tops

7950.5115 - 7950.5117 - 7950.5118 - 7950.5119

7950.5121 - 7950.5123 - 7950.5125 - 7950.5127

7950.5128 - 7950.5129 - 7950.5131 - 7950.5133

User Manual

Gebruikershandleiding

Gebrauchsanweisung

Le mode d’emploi

CONTENT

GLASS ASSEMBLY GUIDE ..................................................................................................................................... 4

ENGLISH

SAFETY TIPS.........................................................................................................................................................5

INTRODUCTION...................................................................................................................................................5

PACK CONTENTS ................................................................................................................................................. 5

INSTALLATION .....................................................................................................................................................6

FIT GLASS PANELS (OPTIONAL) ........................................................................................................................... 6

OPERATION .........................................................................................................................................................7

MANUAL DEFROST..............................................................................................................................................7

CLEANING, CARE & MAINTENANCE....................................................................................................................7

CLEANING THE CONDENSER ............................................................................................................................... 7

TROUBLESHOOTING............................................................................................................................................ 8

TECHNICAL SPECIFICATIONS ............................................................................................................................... 8

ELECTRICAL WIRING............................................................................................................................................ 9

DISPOSAL ............................................................................................................................................................ 9

COMPLIANCE ...................................................................................................................................................... 9

NEDERLANDS

VEILIGHEIDSTIPS ............................................................................................................................................... 10

INLEIDING ......................................................................................................................................................... 10

VERPAKKINGSINHOUD ...................................................................................................................................... 10

INSTALLATIE....................................................................................................................................................... 11

PLAATSEN VAN DE GLASPANELEN..................................................................................................................... 11

BEDIENING........................................................................................................................................................12

HANDMATIG ONTDOOIEN ................................................................................................................................ 12

REINIGING, ZORG & ONDERHOUD....................................................................................................................12

REINIGING VAN DE CONDENSOR ...................................................................................................................... 12

OPLOSSEN VAN PROBLEMEN............................................................................................................................13

TECHNISCHE SPECIFICATIES ..............................................................................................................................14

ELECTRISCHE BEDRADING................................................................................................................................. 14

AFVALVERWERKING .......................................................................................................................................... 14

PRODUCTCONFORMITEIT ................................................................................................................................. 14

DEUTSCH

SICHERHEITSHINWEISE .....................................................................................................................................15

EINFÜHRUNG....................................................................................................................................................15

LIEFERUMFANG................................................................................................................................................. 15

MONTAGE .........................................................................................................................................................16

GLASER EINSETZEN ...........................................................................................................................................16

BETRIEB.............................................................................................................................................................17

MANUELLES ABTAUEN ...................................................................................................................................... 17

REINIGUGN, PFLEGE UND WARTUNG...............................................................................................................17

REINIGEN DES KONDENSATORS ........................................................................................................................ 17

STÖRUNGSSUCHE ............................................................................................................................................. 18

TECHNISCHE SPEZIFIKATIONEN......................................................................................................................... 19

ELEKTROANSCHLÜSSE.......................................................................................................................................19

ENTSORGUNG...................................................................................................................................................19

KONFORMITÄT ..................................................................................................................................................19

FRANÇAIS

CONSEILS DE SECURITE.....................................................................................................................................20

INTRODUCTION.................................................................................................................................................20

CONTENU DE L’EMBALLAGE ............................................................................................................................. 20

INSTALLATION ...................................................................................................................................................21

INSTALLATION DES PAROIS DE VERRE ............................................................................................................... 21

FONCTIONNEMENT .......................................................................................................................................... 22

DÉCONGÉLATION MANUELLE ........................................................................................................................... 22

NETTOYAGE, ENTRETIEN ET MAINTENANCE.....................................................................................................22

NETTOYAGE DU CONDENSATEUR ..................................................................................................................... 22

DEPANNAGE...................................................................................................................................................... 23

SPÉCIFICATIONS TECHNIQUES .......................................................................................................................... 24

RACCORDEMENT ELECTRIQUE..........................................................................................................................24

MISE AU REBUT.................................................................................................................................................24

CONFORMITE.................................................................................................................................................... 24

GLASS ASSEMBLY GUIDE

SAFETY TIPS

Position on a flat, stable surface.

A service agent/qualified technician should carry out installation and any repairs if required. Do not

remove any components or service panels on this product. Consult Local and National Standards to

comply with.

The following:

oHealth and Safety at Work Legislation

oBS EN Codes of Practice

oFire Precautions

oIEE Wiring Regulations

oBuilding Regulations

DO NOT use jet/pressure washers to clean the appliance.

DO NOT use the appliance outside.

DO NOT use this appliance to store medical supplies.

DO NOT use electrical appliances inside the appliance. (e.g. heaters, ice-cream makers etc.)

DO NOT stand or support yourself on the base, drawers or doors.

DO NOT allow oil or fat to come into contact with the plastic components or door seal. Clean

immediately if contact occurs.

Bottles that contain a high percentage of alcohol must be sealed and placed vertically in the

refrigerator.

Always carry, store and handle the appliance in a vertical position and move by holding the base of the

appliance.

Always switch off and disconnect the power supply to the unit before cleaning.

Keep all packing away from children. Dispose of the packaging in accordance with the regulations of

local authorities.

If the power cord is damaged, it must be replaced by an agent or a recommended qualified technician

in order to avoid a hazard.

INTRODUCTION

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this

machine will provide the best possible performance from your product.

PACK CONTENTS

The following is included:

Refrigerator or Freezer

Top glass panel

Rear glass panel

Side glass panels x2

Instruction manual

Collars x6

Bolt assembly x14 sets

Brackets x7

Grub screws x7

Screws x12

Plugs x14

Gastronorm adaptor bar

Adjustable feet x4

We pride ourselves on quality and service, ensuring that at the time of packing the contents are supplied fully

functional and free of damage. Should you find any damage as a result of transit, please contact your dealer

immediately.

INSTALLATION

Note: If the unit has not been stored or move in an upright position, let it stand upright for approximately 12

hours before operation. If in doubt allow to stand.

1. Remove the appliance from the packaging. Make sure that all protective plastic film and coatings

are thoroughly removed from all surfaces.

2. Maintain a distance of 20 cm (7 inches) between the unit and walls or other objects for ventilation

increase this distance if the obstacle is a heat source.

Note: Before using the appliance for the first time, clean the shelves and interior with soapy water.

3. Level the appliance by adjusting the screw feet.

FIT GLASS PANELS (OPTIONAL)

1. Screw the collars to the rim of the appliance.

Note: Ensure the hole in the collar for the grub screw face Inwards.

2. Slot the two side panels into the collars, with the holes in The glass at the top.

Note: Ensure the screw hole furthest from the edge of the panel goes to the back of the appliance.

3. Screw a grub screw into each collar to secure the panels.

Note: Ensure the soft end of the grub screw is the end making contact with the glass.

4. Slot the rear panel into the collars, with the holes in the glass at the top.

5. Screw a grub screw into each collar to secure the panel.

6. Slot the plastic plugs into each of the holes.

7. Screw the brackets to the inside of each pane using the bolt assemblies.

Note: Ensure the short end of the bolt assembly is on the outside of the panels.

8. Place the top panel onto the brackets, ensuring all holes line up.

9. Insert the plugs and attach the top panel to brackets with the bolt assemblies.

OPERATION

Storing Food

To get the best result from your appliance, follow these instruction:

Only store foodstuffs in the appliance when it has reached the correct operating temperature.

Ensure gastronorm bays are full at all times, even if the gastronorms are unused or empty. Empty bays

will greatly reduce efficiency of the appliance.

Do not obstruct the fans inside the appliance.

Turn on

1. Close the door(s) of the appliance.

2. Ensure the power switch is set to [O] and turn on at the socket.

3. Switch on the power [l]. The current temperature within the appliance is displayed.

MANUAL DEFROST

The appliance will automatically run a defrost cycle every six hours.

Note: The cycle starts from the time the appliance is initially powered up.

To manually defrost the appliance:

1. Press and hold the DEFROST button for 5 seconds.

2. The defrost cycle will start immediately and the Defrost LET illuminates. The defrost will last a maximum of

30 minutes

Note: Starting a manual defrost also resets the automatic defrost timer. The next automatic defrost will start

six hours after the manual defrost has finished.

3. Waste water is collected in the waste water tray.

CLEANING, CARE & MAINTENANCE

Switch off and disconnect from the power supply before cleaning.

Clean the interior of the appliance as often as possible.

Do not use abrasive cleaning agents. These can leave harmful residues.

Clean the door seal with water only.

Always wipe dry after cleaning.

Take care when cleaning the rear of the appliance. Sharp edges can cut.

An agent or qualified technician must carry out repairs if required.

CLEANING THE CONDENSER

Periodically cleaning the condenser can extend the life of the appliance. We recommend that our agent or

qualified technician clean the condenser.

TROUBLESHOOTING

If your appliance develops a fault, please check the following table before making a call to your retailer.

Fault

Probable Cause

Action

The appliance is

not working

The unit is not switch on

Check the unit is plugged in correctly and

switched on

Plug and lead are damaged

Call your agent or qualified technician

Fuse in the plug has blown

Replace the fuse

Power supply

Check power supply

Internal wiring fault

Call your agent or qualified technician

The appliance

turns on, but the

temperature is

too high/low

Too much ice on the evaporator

Defrost the appliance

Condenser blocked with dust

Call your agent or qualified technician

Doors are not shut properly

Check doors are shut and seals are not

damaged

Appliance is located near a heat source

or air flow to the condenser is being

interrupted

Move the refrigerator to a more suitable

location

Ambient temperature is too high

Increase ventilation or move appliance to a

cooler position

Unsuitable foodstuffs are being stored in

the appliance

Remove any excessive hot foodstuffs or

blockages to the fan

Appliance is overloaded

Reduce the amount of food stored in the

appliance

The appliance is

leaking water

The appliance is not properly levelled

Adjust the screw feet to level the appliance(If

applicable)

The discharge outside is blocked

Clear the discharge outlet

Movement of water to the drain is

obstructed

Clear the floor of the appliance (if applicable)

The water container is damaged

Call your agent or qualified technician

The drip tray is over flowing

Empty the drip tray(if applicable)

The appliance is

unusually loud

Loose nut/screw

Check and tighten all nuts and screws

The appliance has not been installed in a

level or stable position

Check installation position and change if

necessary

TECHNICAL SPECIFICATIONS

Model

Voltage

Power

(W)

Current

(A)

Temperature

Range

Capacity

Dimensions

HxWxD(mm)

Weight

(kg)

7950.5115

220～240V/50Hz

110

0.8

2～10℃

5xGN1/4 Container

430x1200x335

7950.5117

220～240V/50Hz

110

0.8

2～10℃

6xGN1/4 Container

430x1400x335

7950.5118

220～240V/50Hz

110

0.8

2～10℃

7xGN1/4 Container

430x1500x335

7950.5119

220～240V/50Hz

110

0.8

2～10℃

7xGN1/4 Container

430x1600x335

7950.5121

220～240V/50Hz

110

0.8

2～10℃

8xGN1/4 Container

430x1800x335

7950.5123

220～240V/50Hz

110

0.8

2～10℃

10xGN1/4 Container

430x2000x335

7950.5125

220～240V/50Hz

110

0.8

2～10℃

4xGN1/3 Container

430x1200x395

7950.5127

220～240V/50Hz

110

0.8

2～10℃

6xGN1/3 Container

430x1400x395

7950.5128

220～240V/50Hz

110

0.8

2～10℃

6xGN1/3 Container

430x1500x395

7950.5129

220～240V/50Hz

110

0.8

2～10℃

7xGN1/3 Container

430x1600x395

7950.5131

220～240V/50Hz

110

0.8

2～10℃

8xGN1/3 Container

430x1800x395

7950.5133

220～240V/50Hz

110

0.8

2～10℃

9xGN1/3 Container

430x2000x395

ELECTRICAL WIRING

Appliances are supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard. The plug

is to be connected to a suitable mains socket. Appliances are wired as follows:

Live wire (coloured brown) to terminal marked L

Neutral wire (coloured blue) to terminal marked N

Earth wire (coloured green/yellow) to terminal marked E

All appliances must be earthed, using a dedicated earthing circuit. If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection

being required they must be readily accessible.

DISPOSAL

EU regulations require refrigeration product to be disposed of by specialist companies who remove or recycle

all gasses, metal and plastic components. Consult your local waste collection authority regarding disposal of

your appliance. Local authorities are not obliged to dispose of commercial refrigeration equipment but may be

able to offer advice on how to dispose of the equipment locally.

COMPLIANCE

Parts have undergone strict product testing in order to comply with regulatory

standards and specification set by international, independent, and federal

authorities. Products have been approved to carry the following symbol:

VEILIGHEIDSTIPS

Plaatsen op een vlakke en stabiele ondergrond.

De installatie en eventuele reparaties zijn door een servicetechnicus/vaktechnicus uit te voeren.

Verwijder geen componenten of servicepanelen van dit product.

Raadpleeg en volg de plaatselijk en nationale regelgeving op m.b.t. het volgende:

oWetgeving van gezondheid en veiligheid op de werkplaats

oWerkregels

oBrandpreventie

oIEE bekabelingsnormen

oBouwverordeningen

Dit product NIET reinigen met spuit-/drukreinigers.

Dit product NIET gebruiken voor de berging van medische producten.

In dit product GEEN elektrische apparaten gebruiken (zoals verwarmers, ijsmakers, etc.)

NIET op de kastbasis, lades en deuren staan of als ondersteuning gebruiken.

Laat NIET toe dat olie of vet in contact komt met plastic componenten of deurafdichtingen.

Onmiddellijk reinigen indien dit wel gebeurt.

Uitsluitend geschikt voor gebruik binnenshuis.

Flessen met een hoog alcoholpercentage moeten goed worden gesloten en verticaal in de koelkast

worden bewaard.

Dit product altijd in een verticale positie vervoeren, opbergen en gebruiken. Het product aan de

kastbasis vervoeren.

Alvorens dit product te reinigen dient men altijd de stroomvoorziening uit te schakelen.

Laat verpakkingsmateriaal niet binnen handbereik van kinderen. Verpakkingsmateriaal in

overeenstemming met de regelgeving van de plaatselijke overheden als afval laten verwerken.

Indien de stroomkabel beschadigd raakt, dient men deze door een technicus of een aanbevolen

vaktechnicus te laten vervangen om gevaarlijke situaties te verhinderen.

INLEIDING

Neem de tijd en lees deze handleiding aandachtig door. Een correct gebruik en onderhoud van deze machine

waarborgt de beste prestatie van uw product.

VERPAKKINGSINHOUD

De verpakking bevat het volgende:

Koelkast of vrieskast

Glazen bovenpaneel

Glazen achterpaneel

Glazen zijpanelen x2

Handleiding

Tussendelen x6

Boutunit x14 sets

Beugels x7

Fixeerschroeven x7

Schroeven x12

Pluggen x14

Gastronorm aanpasbare stang

Verstelbare poten x4

Trots op de haar productkwaliteit en dienstverlening en controleer de inhoud van de verpakkingen, tijdens de

verpakkingsfase, op functionaliteit en schade. Mocht u product door transport zijn beschadigd, neem dan

onmiddellijk contact op met uw dealer.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Manuels Réfrigérateur populaires d'autres marques

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manuel utilisateur

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manuel utilisateur

Sharp

Sharp SJ-BA31IEXW2-EU Manuel utilisateur

CORBERO

CORBERO CC2300MCW Manuel utilisateur

KitchenAid

KitchenAid 2205264 Manuel utilisateur

Stengel

Stengel KU 1101 A++ Manuel utilisateur

NEFF

NEFF KI181 Series Manuel utilisateur

Hoshizaki

Hoshizaki Reach-In Manuel utilisateur

Amana

Amana ASD2524VES00 Manuel utilisateur

BOMANN

BOMANN KGC 213 Manuel utilisateur

Danby

Danby DAR044A1SLDD Instructions de montage

Samsung

Samsung RF323TE Manuel utilisateur

Beko

Beko CSA31022 Manuel utilisateur

IKEA

IKEA FROSTIG C 185 E Manuel utilisateur

Electrolux

Electrolux ER 6821 D Manuel utilisateur

True

True TS-28 Manuel utilisateur

Frigidaire

Frigidaire FSC23R5DW9 Manuel utilisateur

Beko

Beko LSP4579W Manuel utilisateur