ECO Spot LED40DE Manuel utilisateur

ECO Spot LED40DE User Manual

The ECO Spot LED40DE is intended for exterior applications but

is also suitable for interior use. Thank you for choosing an ECO

Spot™ Gobo projector. This unit is equipped with a fan cooled heat

pipe to keep the 40W High Power LED running cool. It is also

available as interior version (ES-LED40D).

Please read this manual before installing or operating this fixture,

follow the safety precautions listed below and observe all warnings.

WARNING!

To prevent damage to the LED, always connect the driver

cable to the projector FIRST before plugging it into the

power outlet.

Package Contents



Projector, External LED Driver, Test Gobo, Spare gobo retaining ring and spare drive

belt, Gobo adapter ring for E-Size Gobos

Safety Information

ECO Spot™ LED40DE User Manual

•Place your fixture at a suitable place with good air flow.

•Keep flammable materials away from the fixture.

•Minimum distance to flammable material = 1 ft (0.3m).

•Minimum distance to illuminated surface = 3.3 ft (1.0m).

•Provide a minimum clearance of 4 in (10cm) around air vents.

•Use only genuine spare parts for part replacement.

•Do not look directly into the lamp; it can cause eye damage.

•Always unplug the unit from the power mains before any service is done.

•Light fixtures should be installed and maintained only by qualified personnel with

experience in lighting equipment and general electrical experience.

•Disconnect the fixture from AC power before handling the fixture.

•Always ground (earth) the fixture electrically.

•Use only a power source

that complies with local building and electrical codes and

has both, overload and ground-fault protection.

•Do not use the fixture if the power cable or power plug is in any way damaged,

defective or wet, or if they show signs of overheating.

ECO Spot LED40DE User Manual

Handling Instructions

Warranty

One Year from Date of Purchase. Keep your receipt for reference and contact your dealer

in case of warranty issues.

Projection Lenses

The projector accommodates interchangeable projection lenses to allow optimizing the

projection size and resulting brightness at varying distances. The more narrow the lens,

the smaller and brighter the image will be at a given distance. For example, cutting the

projection size in half, will quadruple its brightness.

Gobo Rotator

If the fixture is equipped with a gobo rotator, it can be turned on/off with the silver push-

button on the front plate underneath the lens. There are no controls for rotating speed or

direction.

Focusing

•There is a weatherproof connector between the driver (power supply) and

projector, which can be opened for easier handling. Always make this

connection first before powering up the driver, otherwise the LED can be

damaged by the power surge.

•Before the initial start-up, please unpack and carefully check for damage caused

during transportation.

•Place your fixture at a suitable place with good air flow.

•Make sure there are no flammable materials close to the lamp.

•When suspending the fixture above ground level, verify that the structure

can hold

at least 10 times the weight of all installed devices.

•Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

•Power up the projector.

•If the fixture is equipped with a gobo rotator, turn it on, once the gobo projects in

the desired position, turn it off.

•Loosen the outer ring around the lens that acts as a water seal.

•Focus the projection by twisting the lens in and out until

the image is well focused.

When used for the first time, the lens will often need to be twisted outwards many

rotations to reach the focusing point. When in doubt, keep going.

•Re-tighten the outer ring to ensure a tight seal of the lens.

ECO Spot LED40DE User Manual

Multi-functional Yoke

Gobo Placement (see Specifications for Gobo Dimensions)

The ES-LED40DE uses D-Size gobos or E-Size gobos with an adapter ring. See the

Specifications for exact dimensions. For max. image size and brightness use D-Size gobos.

The recommended gobo image diameter is 35mm. An Image Diameter of up to 40mm is

possible with some loss in focusing quality for optimal focus, stay within 32mm image

size.

•The yoke can slide over the whole length of the fixture body to accommodate a

wide range of pointing directions.

•The yoke can also serve as stand.

•The yoke can be screwed to a wall or ceiling or fastened with a C-clamp

•Unscrew the thumbscrews to remove the front cover with the projection lens.

•Push the two pins of the gobo retaining ring together and pull out the retaining

ring. Carefully remove the old gobo and replace it with the new gobo.

•Tip: Tilt the projector forward while placing the palm of your hand inside, the old

gobo will fall into your hand.

•If you have a glass gobo, place the more reflective side towards the light bulb.

•Replace the retaining ring and make sure it evenly pushes the gobo all the way

back.

•Replace the front cover and adjust the focus by threading

the projection lens in or

out.

ECO Spot LED40DE User Manual

Line Voltage

100-240V, 50/60Hz, 0.6A, 48W

Ambient Operating Temperature

-13 to 104°F (-25 to 40°C)

Dimensions / Weight

Body without yoke:

10.5 x 6 x 3.75in (L x W x H)

(267 x 153 x 95mm)

The projection lens adds 0.5 to 2in (12 to

50mm) to the length.

Height with yoke: 7.75in (197mm)

Weight 7lbs (3kg)

Gobo Dimensions D-Size

Metal or Glass Gobos and Dichroic filters

The projector takes D-Size gobos:

Outer Diameter (OD): 53mm

Image Diameter (ID): 35mm (max 40mm)

Max Thickness: 4mm

Larger ID up to 40mm is possible with

some loss in focusing quality, for optimal

focus stay within 32mm image size. An

adapter for the smaller E-Size gobos is

included.

LED Lamp

Lens Options

The projector can be equipped with

standard projection lenses of the ECO

Spot line. These lenses are marked based

on a gobo image size of 25mm. With the

larger gobo image size, a given lens

produces a larger image than the lens

specification, see the effective lens angles

in () below. The more narrow the lens, the

smaller and brighter the image will be at

a given distance. Currently these lenses

are available:

IP Ratings

•Extremely high light density for

ultra-efficient projection.

•Power: 40W

•Bulb life 50,000h

•Color Temperature 5,500k, +/-

500k

•Rated Luminous flux: 2,000lm

•Effective luminous flux: 1,500lm

•Wide 25º (effective 35º)

•Medium 20º (eff. 28º)

•Medium Narrow 15º (eff. 21º)

•Narrow 10º (eff. 14º)

•LED Driver: IP65

•Fixture: equivalent to IP62

Autres manuels ECO Spot Éclairage domestique

ECO Spot

ECO Spot LED80 Manuel utilisateur

Manuels Éclairage domestique populaires d'autres marques

JONATHAN Y

JONATHAN Y JYL5019A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL6007A Manuel utilisateur

Philips

Philips Ledino 31606/11/16 Manuel utilisateur

Salus

Salus UG600 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Manuel utilisateur

Hunter

Hunter Bullet Spotlight Kit Manuel d'instructions

Philips

Philips Ledino 16811/87/16 Manuel utilisateur

Philips

Philips 405441213 Manuel utilisateur

Philips

Philips Halogen Light Manuel utilisateur

Pentair

Pentair GLOBRITE Manuel utilisateur

Philips

Philips 55592-30-16 Manuel utilisateur

Livoo

Livoo Night light Manuel utilisateur

Schwaiger

Schwaiger NFL45 Manuel utilisateur

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Manuel utilisateur

MOOD

MOOD CORSIN JY-16 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL8019 Manuel utilisateur

XTRASUN

XTRASUN XTDEOKT1 Manuel utilisateur