EBA 721-06LT Guillotine Manuel utilisateur

Provided By

http://www.MyBinding.com

http://www.MyBindingBlog.com

EBA 721-06LT

Guillotine

Instruction Manual

EBA 721-05 LT GB Operating Instructions

EBA 721-05

Paper clips or hard material will damage the cutting blade!

Children must not operate the machine!

Never leave the blade unattended. Do not extract or

transport the blade without protection!

Danger! Risk of injur !

Do not reach beneath the blade!

Do not cut hard materials or materials which ma splinter!

with side tables

without side tables

Table of contents

1. General .......................................................... 4

1.1 Safet Precautions  .................. 4

1.2 Application ................................................... 4

2. Installation ................................................... 5

2.1 Preparing for installation ............................. 5

2.2 Power suppl ............................................... 6

3. Operation .................................................... 7

Checklist...................................................... 7

3.1 Operating elements ..................................... 8

3.2 Start-up........................................................ 8

Manual foot pedal ........................................ 8

Cutting to a specified dimension ................. 8

Calculating: ................................................. 9

Cut according to markings .......................... 9

Optical cutting line indicator ........................ 9

Mechanical cutting line indicator ................. 9

Eject function ............................................. 9

Multiple cuts function start......................... 10

Exiting program-mode ............................... 10

3.3 Cutting activation....................................... 10

Cutting stop or interruption: ....................... 10

3.4 False clamp plate ...................................... 11

3.5 Programming ............................................ 12

Entering a program ................................... 12

Eject function program .............................. 12

Changing select program .......................... 13

Insert a step .............................................. 13

Delete a step ............................................. 13

Delete a program ...................................... 13

Example of a program ............................... 13

How the example works ............................ 13

Changing the basic settings ...................... 13

Working with programs ............................. 14

Exiting program-mode. .............................. 14

3.6 Basic Settings ........................................... 14

4. Maintenance .............................................. 15

Safet check ............................................. 15

4.1 Setting the cutting depth ........................... 15

4.2 Turning or replacing the cutting stick ........ 16

Cutting test ................................................ 16

4.3 Blade replacement .................................... 17

Removing the blade .................................. 17

Mounting the blade .................................... 18

4.4 Maintenance ever 7 da s ........................ 19

4.5 Maintenance ever 6 months .................... 19

T pe of grease .......................................... 19

5. Malfunctions .............................................. 20

6. Technical data ........................................... 22

7. Accessories ............................................... 22

EC-declaration of conformit ..................... 23

EBA 721-05

1. General

This instruction manual will help ou to learn the

safe and comfortable operation of this machine.

Please read these operating instructions before

putting the machine into operation and observe the

safet regulations.

1.1 Safety Precautions 

Danger!

Non-compliance with the instructions ma

endanger persons.

Warning!

Non-compliance with the instructions ma

cause damage to the machine.

The operating instructions must always be

available for the operator.

All components which could endanger the operator

are covered b a guard. The side panels are

screwed to the machine.

This machine is constructed for "one-man

operation" only!

The dangerous cutting movement is safeguarded b

a cover (3), a two-handed control s stem (2) and a

safet beam guard (1).

1.2 Application

The machine is designed for cutting stacks of paper

to a specified size. Setting the measurement is

done via buttons or hand wheel. Cutting is released

b a "two-handed control s stem".

Danger!

Onl instructed persons are allowed to operate

the machine.

Children must not operate the machine!

Danger!

Do not cut hard materials or materials which

ma splinter.

Warning!

The machine ma onl be used for cutting

paper or similar materials. Paper clips or hard

material will damage the cutting blade.

1. 3.

2. Installation

- Transport the machine on the pallet to its

destination using a pallet truck.

- 6 strong people are required to lift the machine

from the pallet.

- The machine must be installed on a sturd , dr

and level floor.

Danger!

- The machine must not be located outside.

- Do not use in the vicinit of inflammable

liquids or gases.

- Do not use in humid environments.

- Protect mains cable against heat, oil and

sharp edges.

2.1 Preparing for installation

The machine is delivered read for operation. As

an option, side tables, left and right, are available.

These should be mounted so that the surfaces are

level with the main table.

Danger!

The machine must not be put into operation

without the safet light beam.

EBA 721-05

01-03

01-04

2.2 Power supply

The name plate (23) is located at the rear of the

machine.

- Data stated on the name plate

- Voltage "V",

- Frequenc "Hz",

- Power consumption "A"

must correspond to the values of the power suppl

unit.

- Connect the machine to the mains.

- Earth wire must be available.

Standard machines are factor -set as follows:

- Voltage 400V (220V) 3 phase

- Frequenc 50Hz (60Hz).

Machine does not function

- Machine (5) is switched on?

- Ke -switch (4) on?

- Green overload switch (36) is pressed?

- Black overload switch (37) is pressed?

- Check on-site fuse.

If the machine still does not function then the

rotation must be reversed.

The machine is wired according to the IEC

standards. We recommend that alterations to the

rotar direction be made in the socket. It is also

possible to make alterations in the plug b

exchanging "L1" and "L2".

Danger!

Incorrect exchanging of the connections will

endanger the operator. This work must be

carried out b an electrician.

03-01

04-01

3. Operation

Danger!

It is forbidden to operate the machine if the

operating and safet instructions have not

been understood.

Danger!

Please check the safet devices are

functioning and complete before use and after

replacing the blade.

Checklist

- Machine panels:

All panels have to be mounted

- Cutting activation:

The release for cutting is allowed onl if the

"two-hand safet device" (1) is operated at the

same time.

- Safet light beam

Do not reach into the cutting area (38) when in

motion.

We recommend ou keep a record of our test

results.

Cutting sequence (1) with automatic clamping:

Airtable (9) optional

The airtable allows paper to be easil positioned.

Setting clamping pressure (7)

The clamp pressure can be adjusted using the

adjustment knob (7).

panel (19).

EBA 721-05

01-01

67 01

3.1 Operating elements

(1) Safet two-handed control s stem

(2) Backgauge control

(3) Backgauge

(4) Ke switch

(5) Main switch

(6) Paper knock-up block

(7) Clamp pressure adjustment

(8) Foot pedal

(9) Airtable switch

(10) Program number

(11) Program step

(12) LED "M" displa memor

(13) LED "E" displa eject

(14) LED "S" dspla error indication

(15) Displa cutting size

(16) Backgauge, backwards fast

(17) Electronical hand-wheel for fine adjustment

(18) Backgauge, forwards fast

(19) Clamp pressure

(20) Program ke s

(21) Basic setting F1, F2, F3, eject

(22) Displa false clamp plate

(23) Ke pad with calculator

(24) Displa impuls of backgauge movement

(25) Displa in cm or inch

(26) Changeover cm-inch.

3.2 Start-up

- Position the main switch (5) to "I".

- Insert the ke (4) for the control panel and turn to

the right.

- Press button © backgauge (3) moves to the

rear and searches for the reference position, wait

until a measurement is shown on the displa .

Manual foot pedal

Pre-clamping can be performed using the foot pedal

(8) (e.g. folded stacks).

Cutting to a specified dimension

(14) appears.

LED "S" disappears.

- Insert paper and move b means of the paper

knock-up block to the backgauge (6).

- Release the cut (see 3.3 "Cutting activation").

67 02

Calculating:

the calculated measurement of 18.

Cut according to markings

- Adjust the backgauge (16) to the back.

- Insert paper and move b means of the paper

knock-up block to the backgauge.

- Turn the hand-wheel (17) to the front until the

marking on the paper to be cut is below the

cutting line indicator. The more the hand-wheel is

turned the faster the backgauge will move. For

quick motion use ke (18).

- Release the cut.

Optical cutting line indicator

An optical cutting line (45) indicates the exact

position of the cut. The light beam indicates where

the cut will be made.

Mechanical cutting line indicator

The clamp (24) can be used as cutting line

indicator for exact cutting. Pre-clamping can be

performed using the foot pedal (8).

Eject function

If button E is pressed, the backgauge will advance

to the preset measurement, ejecting the material to

be cut, then automaticall return to the position

shown on the displa .

Autres manuels pour 721-06LT Guillotine

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels EBA machine à relier

EBA

EBA 435 E Manuel utilisateur

Manuels machine à relier populaires d'autres marques

GBC

GBC CombBind C800pro Manuel utilisateur

JBI

JBI Alpha-Doc MKIII Manuel utilisateur

GBC

GBC CombBind A20 Manuel utilisateur

GBC

GBC DocuBind P100 Manuel utilisateur

Peach

Peach PB300-20 Manuel utilisateur

Morgana

Morgana DigiBook 450 Manuel utilisateur

Rexel

Rexel CB345E Instructions de construction

GBC

GBC AP-2 Manuel utilisateur

Opus

Opus MB 300 Manuel utilisateur

Duplo

Duplo DC-645 Manuel utilisateur

Akiles

Akiles AlphaBind Guide de démarrage rapide

ibico

ibico Thermal Binder 260 Manuel utilisateur

Rollabind

Rollabind PBS 2000 Manuel utilisateur

SYSFORM

SYSFORM CP340H Manuel utilisateur

GBC

GBC THERMALBINDER400T Manuel utilisateur

GBC

GBC CombBind C20 Manuel utilisateur

Renz

Renz RENZ DTP 340A Manuel du propriétaire

Ricoh

Ricoh RB5020 Manuel utilisateur