Eaton EBMAFDD24 Manuel utilisateur
EBMAFDD14-36 - ARC FAULT DETECTION DEVICE (AFDD) DISTRIBUTION BOARD
Instruction leaflet LT1230 (01/21)
IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician in
accordance withcurrent electricalengineeringCodesof Practice, Requirements forthe Electrical Installations(IET Wiring Regulations
BS7671), Construction (Design and Management)Regulations, HSG150- Health and Safety in Construction, Statutoryrequirements and
any specific instruction issued bythe Company.
2. After completingthe installationandtestingofthisproduct it is essentialthat thisleaflet is drawn tothe attentionof the person
responsibleforits future operationandmaintenance, andis at all timesavailable forreadyreference.
3. Thesenotesassume throughout that the product isdisconnected fromthe supply. It is essential that this isdone beforeanyworkis
carried out.
4. TheseDistribution Boardsa re designed for use with Eaton AFDDs only. Failure to comply willresult in i nvalid warranty and certification.
2.4Nm
300957 –EBMAFDD14 - 14 Way DB
300958 –EBMAFDD24 - 24 Way DB
300959 –EBMAFDD36 - 36 Way DB
Clip fit
This board is intended to be used
with Eaton AFDD devices
up to 40A
All unused ways must
Be covered with a
blanking module,
assembled and
fitted in gangs of 3.
EMPB
Important:
Orientate clip next
to busbar stack
Optional
SPD
position
Incoming
Switch position
Before fitting the AFDD to the busbar ensure the terminals are
fully open. Locate the AFDD square to the
busbar and tighten the terminals.
General note: Tightening torque for
M5 thread forming screws is 3.8Nm
Insert Lock into hole tighten back nut Remove plastic knob
Fitting Optional Door
Lock EMDL & EMPL
SP MCB / RCBO
Fit SP device on live stab,
ASLTT1001 direct
connection on neutral
stab and EMBP blank in
the spare module space.
ASLTT1001
SP Device
EMBP
Earth bolt
15Nm
2.5Nm
Fitting Incoming Switch
EMS1253 & EMS1253N
Before fitting the switch ensure the terminals arefully open. Locate
the switch onto the stabs ensuring the din rail clip is hooked over the
mounting bracket.
Mounting bracket
Din rail mounting clip
Fitting Neutral Link assy- 300960
Inner Cover Cutaway for 4P Incomer
When a 4 pole incomer is fitted the cutaway on
the inner cover needs to be removed .
Mounting
bracket hook
4.5Nm Single Phasing Kit - 300969
Position the two comb busbars back to back
and fit in the L1/L2/L3 fork terminals of the
switch on the incoming side.
2.4Nm
Connecting Boards Together
Connect downstream of the
Incoming switch so secondary
board switches with primary board.
Connect upstream of the incoming
switch so secondary board switches
independently of the primary board.
Neutrallink connection
Remove knock out
for N cable to exit
When the neutral link kit is fitted
then the cable is made up with a M6
lug and connected to the link
terminal as shown. The other end is
connected to the incoming neutral
terminal on the secondary board.
Make up 16mm² tri rated cable with Cembre ANE 3-U 5
fork connectors and connectto the incoming switch
fork terminals of the primary board. The other end of
the cables are connected to the main incoming
terminals on the Secondary board.
Secondary board 80A max.
Connecting boards with Neutrallink kit
Slide the neutral assembly into position with the mounting brackethook
engaged in the incomer mount. Bolt the neutral copper connection to the
busbar with the M5 x 12 bolt and spring washer provided to 4.5Nm.
6.8Nm
6Nm <=10mm²
9Nm >10mm²
2.4Nm
Surge SupressionDevice -300961 type 1 and 300962 type1&2
Before Installation: Verify that the system is wired in aThree Phase Star configuration and that the voltage rating of the system matches the
voltage rating ofthe SPD as shown on the label. If the Neutral to Earth voltage is greater than 5 VAC, then a problem may ex ist in the electrical
system. The SPD may be installed; however, a qualified person should be consulted to correctthe problem.
Installation Instructions:
• Disconnect the neutral cable from the SPD and remove the SPD and MCB from the
mount. Fit the mounting bracket assembly to the back plate in theposition shown.
• Fit 63A 4P MCB onto the stabs with the back end hooked on the din rail whilst
fitting the SPD device on the din rail next to it. Tighten the MCB terminals to 2.4Nm.
• Reconnect the Neutral cable to the SPD. Tighten to 2.4Nm.
• Connect the EARTH wire to the nearest common earth bolt. Tighten to 15Nm.
Energise the System. The Indicator should remain green.If the indicator turns RED,
de-energise and contactthe Technical Servicesdepartment.
2.4Nm
Separation Shield -300965
In some arrangements, when the distribution board is used in a cluster, a 20mm
spacer is required to allow thebottom and top of the boards to be flush
A separation shieldis required when boards aremounted on
top of each other and a barrieris required between them.
Position the separation shield
inside the board and fix with
M5 screws provided.
Alignment Spacer-300966
Fit the spacer to the top or bottom of the board and
fix with M5 screws. The removed Distribution board
gland plate can be refitted to the spacer if required.
20mm
spacer
SPD mounting
bracket assembly
Remove shield from stabs
before fitting the SPD
feeder MCB
H630 x W440
x D130 mm
H1260 x W440
x D130 mm
H900 x W440
x D130 mm
2.4Nm
Neutral
connection
2.4Nm
Warning -
Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property rights in the
product which it manufactures (whether or not listed in this leaflet) and that it
will take legal action against any party found to be manufacturing, using, or
selling any article which infringes the company’s intellectual property. All
marks in this document identified with an R symbol or a TM symbol adjacent
to the mark are trademarks of Eaton.
© 2020 Eaton Electric Limited.
All rights reserved. www.eaton.com/recycling
The use to which this product is put and its place of installation is outside our
control. Particular care should therefore be taken to follow the instructions
given here and to ensure their continued availability in conjunction with the
use of the product.
No responsibility can be accepted by us if these instructions are disregarded.
Further copies of these instructions and information concerning the
installation and proper use of this product can be obtained by contacting the:
Technical Services Department
Eaton Electric Limited, Middleton,Manchester, M24 1GQ.
Tel: +44(0)8700 545 333,
email: techsupportemea@eaton.com
Maximum Thermal Ratings
Maximum Incomer
125ASwitch = 125 InA
FED FROM
______________________________________________________
CONTRACTOR
______________________________________________________
INSTALLATIONDATE
_______________________________
INCOMINGCABLESIZE
_______________________________
Maximum Outgoer InC RDF
AFDD 40A (6kA) = 40A 0.75
AFDD 25A (10kA) = 25A 0.75
MAIN BUSBARCIRCUITS
Ce manuel convient aux modèles suivants
8
Autres manuels Eaton Parafoudre
Eaton
Eaton NEC Article 240 Manuel utilisateur
Eaton
Eaton COOPER POWER UltraSIL VariSTAR Series Manuel utilisateur
Eaton
Eaton SPBT12-280/3 Manuel
Eaton
Eaton SPI-35/440 Manuel
Eaton
Eaton DSFi Manuel utilisateur
Eaton
Eaton **CF***10 series Manuel utilisateur
Eaton
Eaton SP2 Mode d’emploi
Eaton
Eaton Powerware SPDT60-255 Manuel utilisateur
Eaton
Eaton BUSSMAN Series Manuel utilisateur
Eaton
Eaton MEMSHIELD 3 EPBN1SPD123 Manuel de service
Eaton
Eaton AFDD+ Manuel
Eaton
Eaton IM01005012E Manuel utilisateur
Eaton
Eaton BSPM2275TN Manuel utilisateur
Eaton
Eaton PVD40 Series Manuel utilisateur
Eaton
Eaton Crouse-hinds series Manuel utilisateur
Eaton
Eaton EM3SSK3T2 Manuel utilisateur
Eaton
Eaton FAZ-B1-2 Manuel utilisateur
Eaton
Eaton Protection Box 5 Manuel utilisateur
Eaton
Eaton AFDD+ Manuel
Eaton
Eaton SPD Series Manuel utilisateur
Manuels Parafoudre populaires d'autres marques
OBO Bettermann
OBO Bettermann ÜSM-20-230I1PE65 Manuel utilisateur
Minuteman
Minuteman MMS7120RCT Manuel utilisateur
Leviton
Leviton 52412-DS3 Manuel utilisateur
Savio
Savio LZ-07 Manuel utilisateur
Siemens
Siemens HNM3M120 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric LITOL LTM-125RF Manuel utilisateur