Eaton Tripp Lite SmartPro Series Instructions de montage

p/n: 614-40195

Revision 01

SMX1500XLRT2U

SMX1500XLRT2UN

SMX3000XLRT2UA

SMX3000XLRT2UN

BP48VRM2U

BP72VRM2U

Advanced User Guide

Eaton®Tripp Lite Series SmartPro

Eaton reserves the right to change specifications without prior notice Eaton is a registered trademark of Eaton All other trademarks are

property of their respective companies

express written approval of Eaton

SSaaffeettyy IInnssttrruuccttiioonnss

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be

followed durin installation and maintenance of the UPS and batteries.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense

This is a category C2 UPS product In a residential environment, this product may cause radio

interference, in which case the user may be required to take additional measures

Supplier's Declaration of Conformity of Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules Operation is subject to the following two

conditions:

1 this device may not cause harmful interference, and

2 this device must accept any interference received, including interference that may cause

undesired operation

For questions regarding this FCC SDoC declaration, contact Eaton Corporation by telephone or

through the Internet

Eaton Corporation 8609 Six Forks Road,

Raleigh, NC 27615, USA

Telephone: 800-356-5794

SSppeecciiaall SSyymmbboollss

The following are examples of symbols used on the product to alert you to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of

electric shock symbol

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's

manual for additional information, such as important operating and maintenance

instructions

Information, advice, help

Read the documentation provided

Disconnect input plug

Before maintenance, first shut down the UPS then disconnect the AC power

source, internal and external batteries then discharge capacitors by pressing the

ON button and wait 5 minutes

This equipment should only be used in a dry indoor environment

Operating range of temperature

Operating range of humidity

The UPS and their batteries must be kept in a ventilated place

SSaaffeettyy ooff PPeerrssoonnss

• The system has its own power source (the battery) Consequently, the power outlets may be

energized ven if the systems is disconnected from the AC power source Dangerous voltage

levels are resent within the system It should be opened exclusively by qualified service

personnel

• The system must be properly grounded at all times

• The battery supplied with the system contains small amounts of toxic materials To avoid

accidents, the directives listed below must be observed:

–Servicing of batteries should be performed or supervised by personnel knowledgeable about

batteries and the required precautions

–When replacing batteries, replace with the same type and number of batteries or battery

packs

–Do not dispose of batteries in a fire The batteries may explode

–Batteries constitute a danger (electrical shock, burns) The short-circuit current may be very

high

• Precautions must be taken for all handling:

–Wear rubber gloves and boots

–Do not lay tools or metal parts on top of batteries

–Disconnect charging source prior to connecting or disconnecting battery terminals

–Determine if battery is inadvertently grounded If inadvertently grounded, remove source

from ground Contact with any part of a grounded battery can result in electrical shock The

likelihood of such shock can be reduced if such grounds are removed during installation and

maintenance (applicable to equipment and remote battery supplies not having a grounded

supply circuit)

PPrroodduucctt SSaaffeettyy

• To connect the UPS, instructions and operation described in the manual must be followed in the

indicated order

• CAUTION - To reduce the risk of fire, the unit connects only to a circuit provided with 20 or 30

amperes maximum branch circuit overcurrent protection in accordance with the National Electric

Code, ANSI/NFPA 70 (US installations only)

• Check that the indications on the rating plate correspond to your AC powered system and to the

actual electrical consumption of all the equipment to be connected to the system

• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall

be easily accessible

• Never install the system near liquids or in an excessively damp environment

• Never let a foreign body penetrate inside the system

• Never block the ventilation grates of the system

• Never expose the system to direct sunlight or source of heat

• If the system must be stored prior to installation, storage must be in a dry place

• The admissible storage temperature range is -25ºC to +55ºC without batteries, 0°C to 40°C with

batteries

• The system is not for use in a computer room AS DEFINED IN the standard for the Protection of

Information Technology Equipment, ANSI/NFPA 75 (US installations only)

SSppeecciiaall PPrreeccaauuttiioonnss

• The unit is heavy: wear safety shoes and use vacuum lifter preferentially for handling operations

• All handling operations will require at least two people (unpacking, lifting, installation in rack

system)

• Before and after the installation, if the UPS remains de-energized for a long period, the UPS must

be energized for a period of 24 hours, at least once every 6 months (for a normal storage

temperature less than 25°C) This charges the battery, thus avoiding possible irreversible

damage

• During the replacement of the Battery Module, it is imperative to use the same type and number

of element as the original Battery Module provided with the UPS to maintain an identical level of

performance and safety If there are any questions, don’t hesitate to contact your local Eaton

representative

• All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY

There are NO USER SERVICEABLE PARTS inside the UPS

• For potential safety issue on defective UPS : DISCONNECT INTERNAL BATTERY for storage and

transportation

Tripp Lite by Eaton SmartPro Advanced User Guide 614-40195—Rev 01 vii

TTaabbllee ooff CCoonntteennttss

11 IInnttrroodduuccttiioonn....................................................................................................................................................................................................................................................................................................11

1 1 Environmental Protection 2

1 2 Benefits 3

22 PPrreesseennttaattiioonn ..................................................................................................................................................................................................................................................................................................55

2 1 Standard installation 5

2 2 Rear panel 6

2 3 Optional accessories 6

33 IInnssttaallllaattiioonn ......................................................................................................................................................................................................................................................................................................77

3 1 Inspecting the Equipment 7

3 2 Recommended Positions 7

3 3 Connecting the Internal Battery 11

3 4 EBM Connections 11

3 5 UPS Connections 13

3 6 Connection with a FlexPDU (Power Distribution Unit) 14

3 7 Connection with a HotSwap MBP (Maintenance ByPass) 14

3 7 1 UPS Start-Up with the HotSwap MBP Module 15

3 7 2 HotSwap MBP Module Test 15

44 IInntteerrffaacceess aanndd CCoommmmuunniiccaattiioonn .......................................................................................................................................................................................................................................... 1177

4 1 Control Panel 17

4 2 LCD Description 17

4 3 Display Functions 20

4 4 User Settings 21

4 5 Communication Ports 23

4 6 UPS Remote Control Functions 24

4 7 Power Alert Software 28

4 8 Cybersecurity 28

55 OOppeerraattiioonn........................................................................................................................................................................................................................................................................................................ 2299

5 1 Start-up and Normal Operation 29

5 2 Starting the UPS on Battery 29

5 3 UPS Shutdown 29

5 4 Operating Modes 30

5 5 Return of AC Input Power 30

5 6 Configuring Battery Settings 30

5 7 Retrieving the Event and Fault Logs 31

UUPPSS MMaaiinntteennaannccee................................................................................................................................................................................................................................................................................ 3333

6 1 Equipment Care 33

6 2 Storing the Equipment 33

viii Tripp Lite by Eaton SmartPro Advanced User Guide 614-40195—Rev 01

6 3 When to Replace Batteries 33

6 4 Replacing Batteries 33

6 5 Replacing the UPS Equipped with a HotSwap MBP 35

6 6 Recycling the Used Equipment 36

77 TTrroouubblleesshhoooottiinngg .................................................................................................................................................................................................................................................................................. 3377

7 1 Typical Alarms and Faults 37

7 2 Alarm or Fault Codes 38

7 3 Silencing the Alarm 39

7 4 Service and Support 39

88 SSppeecciiffiiccaattiioonn aanndd TTeecchhnniiccaall CChhaarraacctteerriissttiiccss.................................................................................................................................................................................................... 4411

8 1 UPS Model List 41

8 2 Extended Battery Module Model List 41

8 3 Weights and Dimensions 42

8 4 Electrical Input 42

8 5 Electrical Input Connections 42

8 6 Electrical Output 42

8 7 Electrical Output Connection 43

8 8 Battery 43

8 9 Environmental and Safety 44

99 GGlloossssaarryy .......................................................................................................................................................................................................................................................................................................... 4455

Table of Contents