Eaton S611 Manuel

Installation Leaet IL03901007E Effective June 2011

S611 User Interface Remote Mounting

Installation Leaﬂet

Disconnect power in accordance with federal, state, and local codes and remove the S611 from the enclo-

sure or mounting panel.

NOTE: Servicing the S611 while installed in an enclosure or mounted vertically on a panel is not recom-

mended.

Place the unit on a clean work surface.

Cover Removal

1. Disconnect all control wiring and tie wraps securing any wiring to the cover assembly.

2. Remove cover screws with nuts. 6 each on Frames A – D, 4 each on Frames E - F.

NOTE: Cover screw nuts are prevented from rotating but are not retained in place by the pole

supports. Do not allow hardware to fall into the soft starter.

3. Lift top of cover approximately 6” to gain access to the BYPASS VOLTAGE contactor

connector mounted on the Printed Circuit Board (PCB). See Figure 1.

4. Press locking tab on BYPASS VOLTAGE contactor connector and disconnect from the PCB.

5. Carefully rotate cover to rest onto work surface as shown. See Figure 2.

Figure 1 - Contactor Connector Figure 2 - Cover Position

Mounting The Remote Display

If necessary, remove the User Interface from the cover using a 30mm pilot device tool (E22CW recom-

mended).

1. Drill or punch two 30mm pilot holes on 1.75-inch centers a minimum of 1.60 inches (40.6 mm)

from every door gasket (see Figure 3).

2. Insert remote display through the door and add two gaskets provided behind the door

(see Figure 4).

Installation Leaet IL03901007E

Effective June 2011

S611 Soft Starters

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL03901007E

June 2011 Rev.001

PowerChain Management is a registered

trademark of Eaton Corporation.

All other trademarks are property of their

respective owners.

Figure 3 - Pilot Device Holes - Inch[mm]

Minimum to all

gaskets ordoor

mounteddevices

1.60

[40.6]

1.75

[44.5]

Gaskets

E22CW

Tighten

Figure 4 - Door Cut Away For Clarity

3. Orient strain relief bracket with respect to your chosen cable routing.

4. Add two jam nuts provided and tighten 30mm pilot device tool until the strain relief bracket is

flush with the enclosure door, tighten an additional ½ of a turn.

Connecting the Remote Display

1. Route cable from User Interface to PCB (see Figures 5 & 6).

2. Secure cable to the strain relief bracket using any suitable tie wrap.

3. Reinstall cover assembly.

Figure 5 - Interconnecting Cable - PCB Figure 6 - Interconnecting Cable - User Interface

Cover Reinstallation

1. As the cover is placed onto the supports, carefully guide wiring into place.

2. Ensure that the BYPASS VOLTAGE contactor connector is properly connected prior to installing

the cover screws.

3. Install and torque all cover assembly screws to 22 – 27 lb-in.

4. Reinstall control wiring.

Autres manuels pour S611

Table des matières

Autres manuels Eaton Contrôleurs

Eaton

Eaton XC-CPU101 Series Manuel

Eaton

Eaton ELCM TC Series Manuel utilisateur

Eaton

Eaton CGLine+ Web-Controller Manuel utilisateur

Eaton

Eaton AMPGARD RVSS Manuel d'utilisation et d'entretien

Eaton

Eaton xComfort CDAE-01/01 Manuel utilisateur

Eaton

Eaton Digitrip RMS Manuel

Eaton

Eaton MMX11 Series Manuel utilisateur

Eaton

Eaton ELC-PC12NNAR Manuel utilisateur

Eaton

Eaton DS7-34 SX041N0 Series Manuel

Eaton

Eaton A210 Manuel

Eaton

Eaton XC-CPU121-2C256K Manuel

Eaton

Eaton EPCT Fire Series Manuel utilisateur

Eaton

Eaton xComfort CSAU-01/01 Manuel

Eaton

Eaton SC100 Manuel utilisateur

Eaton

Eaton CEAG CG-Controller Manuel utilisateur

Eaton

Eaton xComfort CSAU-01/01-10 Manuel utilisateur

Eaton

Eaton EMS Series Manuel utilisateur

Eaton

Eaton ADS8 Series Manuel

Eaton

Eaton Cutler-Hammer ATC-300 Manuel utilisateur

Eaton

Eaton xComfort Bridge Manuel de la liste des pièces

Eaton

Eaton SC300 Manuel utilisateur

Eaton

Eaton SC100 Manuel utilisateur

Eaton

Eaton Crouse-hinds series Manuel utilisateur

Eaton

Eaton CAAE-01/01 Manuel

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur