Eaton PXGMS Power Xpert Gateway Minislot UPS Manuel de programmation

Eaton®Power Xpert®Gateway Minislot (PXGMS) UPS Card

Quick Start Instructions

Package Contents

lPower Xpert Gateway Minislot (PXGMS) UPS Card

lUSB Cable

lQuick Start Instructions

Ident

Power

Act

100

PXGMS UPS

Restart TX RX

Setup

CMN

Status

DHCP EMP

Ethernet 10/100

Help Desk Numbers

United States 1-800-356-5737 or 1-800-843-9433

Canada 1-800-461-9166 ext 260

All Other Countries Call your local service representative

Web Site www.eaton.com/pxgms

NOTE: On the Web site opening page, click Support and select the

Customer Service link for more information.

Eaton, Power Xpert, and PredictPulse are registered trademarks of Eaton

Corporation or its subsidiaries and affiliates. Google Chrome is a trademark of

Google Inc. Linux is a registered trademark of Linus Torvalds. Microsoft, Internet

Explorer, and Windows are registered trademarks of Microsoft Corporation in the

United States and in other countries. Mozilla and Firefox are registered

trademarks of the Mozilla Foundation. All other trademarks are property of their

respective companies.

part of this document may be reproduced in any way without the express written

approval of Eaton Corporation.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 1

TABLE OF CONTENTS

Section 1 Installation Checklist ........................................................................ 2

Section 2 Install the Card ................................................................................. 3

Section 3 Connect the Card to the Computer .................................................. 5

Section 4 Install the USB Driver Software ...................................................... 7

Section 5 Obtain a DHCP-Assigned IP Address ............................................. 11

Section 6 Assign an IP Address Manually ..................................................... 15

Section 7 Disable Browser Compatibility Mode ............................................ 18

Section 8 Register a PredictPulse Subscription ............................................. 20

2 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2

Section 1 Installation Checklist

1. Verify that the following items are available:

oPower Xpert Gateway Minislot (PXGMS) UPS Card package contents

(card, cable, Quick Start Instructions)

oPhillips®screwdriver

oAvailable USB port on a computer running Microsoft®Windows®

oWeb browser (Microsoft Internet Explorer® version 8.0 and higher,

Mozilla®Firefox®, or Google Chrome™ are recommended)

2. If you are going to use Dynamic Host Configuration Protocol (DHCP), provide

your local network administrator with the card's MAC address. The MAC

address is located on either the shipping box label or the label on this card.

oMAC Address _____________________________________________

3. If you are not going to use DHCP to provide any of the settings listed below,

contact your local network administrator for the settings.

In the table below, check the DHCP check box or enter the values for manual

configuration.You will reference this data later in the procedure.

4. If you need e-mail functionality, obtain the SMTP mail server's IP address or

host name. If using the SMTP host name, verify that you also have the

Name Server IP address (see Step 3).

oSMTP (mail server) IP Address

or Host Name _____________________________________________

Item DHCP* Manual Configuration

IPv4 oCard IP Address: ________________________

Netmask: ________________________

Gateway: ________________________

DNS – Name Servers oName Server #1: ________________________

Name Server #2: ________________________

Name Server #3: ________________________

DNS – Domain oDomain: ________________________

* The network administrator normally sets up the DHCP server to provide a static IP address each time

the card makes a DHCP request.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 3

Section 2 Install the Card

Note: The hot-swappable PXGMS card can be installed without turning off the

UPS or disconnecting the load.

Note: If your UPS is a 93PM, there may be a metal strip that prevents you

from installing the PXGMS card. If so, locate the metal strip bolted to

the top of the UPS. Remove the three bolts that attach the metal strip.

Then, follow the procedure to install the PXGMS card.

To install the PXGMS card:

1. On the PXGMS card, verify that all six DIP switches are in the OFF position

(see Figure 1).

Figure 1. Verify DIP Switches are OFF

2. If not already done, record the MAC address from either the shipping box

label or the label on this card for future reference (see the "Installation

Checklist" on page 2).

3. Remove the minislot cover from the UPS. Retain the screws.

Note: If another card is already installed with an attached communication

cable, disconnect the cable and then remove the card.

4. To prevent electrostatic discharge (ESD), place one hand on a metal surface,

such as the UPS rear panel.

Ident

Power

Act

100

PXGMS UPS

Restart

Setup

CMN

Status

DHCP

EMP

Ethernet 10/100

13456

OFF

4 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2

5. Slide the card into the open slot and secure it with the screws removed in

Step 2 (see Figure 2).

Figure 2. Secure the PXGMS Card

6. From your laptop, go to www.eaton.com/pxgms.

7. On the Features tab, click the Download Configuration File link to

download the configuration file.

8. Save the driver configuration file (powerxpert.inf) to the C: drive using the

default location or a folder you select. Note the path of the downloaded file

on your computer. (Never download the file to your desktop.)

Ident

Power

Act

100

PXGMS UPS

Restart

Setup

CMN

Status

DHCP

EMP

Ethernet 10/100

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 5

Section 3 Connect the Card to the Computer

To connect the card to the computer:

1. Plug the small connector at the end of the supplied USB configuration cable

into the setup port on the card (see Figure 3).

Figure 3. Install the USB Cable

2. Plug the other end of the USB cable into the USB port on the computer. The

Windows operating system detects new hardware.

Note: If a message indicates that the device driver software was not

successfully installed, click Ignore.

Note: You may see a pop-up message window that shows “Found new

hardware.” This indicates that the hardware installed successfully.

Ident

Power

Act

100

PXGMS UPS

Restart TX RX

Setup

CMN

Status

DHCP EMP

Ethernet 10/100

6 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2

3. Connect an active Ethernet cable (not supplied) to the Ethernet 10/100

connector on the PXGMS card (see Figure 4).

Figure 4. Install the Ethernet Cable

4. Wait for the power light and status light on the installed card to illuminate.

This takes about two minutes.

5. Open a Web browser and type the default IP address (192.168.200.101).

6. Did the Power Xpert Gateway software open to the PXGMS page?

lIf yes, the driver has already been installed automatically. Either verify the

IP address assigned through DHCP or manually enter a static (fixed) IP

address for the card’s network connection:

a.To verify the DHCP-assigned IP address, go to page 13.

b.To manually enter a fixed IP address, go to page 16.

lIf no, the driver has not been installed. Go to the next section, "Install the

USB Driver Software" on page 7 in order to confirm that you have the most

current USB Driver software. If not, you need to install or update the USB

Driver software.

Ident

Power

Act

100

PXGMS UPS

Restart

Setup

CMN

Status

DHCP

EMP

Ethernet 10/100 +

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 7

Section 4 Install the USB Driver Software

The steps you use to install the driver software depend on your operating system

(OS). This procedure provides instructions for installing driver software on a

Windows 7 OS.

Note: Windows 8 steps are basically the same as Windows 7, although the

dialog displays may differ somewhat.

Note: The PXGMS and PXGX UPS cards use the same driver.

Note: You can use either the Device Manager path or the Devices and Printers

path to browse for the driver software and install it. This procedure uses

the Device Manager.

To install the driver from the Device Manager:

1. C l i ck Start in the Start bar. Type Device in the search box.

2. Select Device Manager from the list above the search box. The Device

Manager opens.

3. Locate RNDIS/Ethernet Gadget under either Other Devices or Network

Adapters (see Figure 5).

lIf you do not see RNDIS/Ethernet Gadget in either list, you do not have a

cable connected to the card. Connect the computer to the card. Go back to

Step 1.

lIf RNDIS/Ethernet Gadget is listed under Other Devices, the driver is not

installed. Go to Step 4.

lIf RNDIS/Ethernet Gadget is listed under Network Adapters, a driver is

installed already, but you it may not be the most up to date driver. Go to

Step 4.

8 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2

Figure 5. Device Manager Window

4. Right-click RNDIS/Ethernet Gadget to display the menu and select Update

Driver Software.

lIf a pop-up message displays, “The best driver is already installed,” click

Close and go to Step 10.

lOtherwise, go to Step 5.

5. Select Browse my computer for driver software (see Figure 6). Click

Next. The next page displays.

Figure 6. Update Driver Software Window – Search Method

Autres manuels pour PXGMS Power Xpert Gateway Minislot UPS

Table des matières

Autres manuels Eaton Adaptateur

Eaton

Eaton DX-COM-STICK Manuel

Eaton

Eaton Powerware 9305 UPS Manuel de programmation

Eaton

Eaton xComfort CEMP Series Manuel utilisateur

Eaton

Eaton Cutler-Hammer RSS 36-SD-ST Manuel utilisateur

Eaton

Eaton xComfort CDAP-01 Series Manuel utilisateur

Eaton

Eaton PowerXL DX-NET-ETHERCAT-2 Manuel utilisateur

Eaton

Eaton AQB-L400 Manuel utilisateur

Eaton

Eaton EBT 01 Manuel utilisateur

Eaton

Eaton HALOHOME HWAD1BLE40AWH Manuel utilisateur

Eaton

Eaton TRIPP LITE U444-06N-HU-C Manuel utilisateur

Eaton

Eaton Cutler-Hammer APPS12A Manuel utilisateur

Eaton

Eaton xComfort CSAP-01 Series Manuel

Eaton

Eaton SKF-HA Manuel

Eaton

Eaton DX-COM-STICK3-KIT Manuel

Eaton

Eaton Power Defense PDC9-ETU Manuel

Eaton

Eaton TRIPP LITE U209-000-R Manuel utilisateur

Eaton

Eaton TRIPP LITE U444-06N-DP4K6B Manuel utilisateur

Eaton

Eaton XT-RJ45-ETH-RS232 Manuel

Eaton

Eaton TRIPP LITE U209-30N-IND Manuel utilisateur

Eaton

Eaton xComfort CHVZ-01/04 Manuel

Eaton

Eaton TRIPP LITE U209-005-DB25 Manuel utilisateur

Eaton

Eaton TRIPP LITE U444-06N-HU-C Manuel utilisateur

Eaton

Eaton TRIPP LITE Series Manuel utilisateur

Eaton

Eaton TRIPP LITE U209-30N-IND Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur