Eastwood FAIRMOUNT 12PC BEARING SPLITTER/PULLER KIT Manuel utilisateur
12PC BEARING
SPLITTER/PULLER KIT
INSTRUCTIONS
Item #31472
The FAIRMOUNT 12 PIECE BEARING SPLITTER/PULLER KIT includes all the components required
to pull and separate bearings and gears from transmission shafts, differential assemblies and other
automotive components. This tool, constructed of robust, high-strength steel alloy forgings, will
provide years of reliable service.
CONTENTS
(1) 6” Yoke - A
(1) 9/16” Pressure Screw - B
(2) 2” Bearing Separator Jaws - C
(2) 3” Bearing Separator Jaws - D
(2) 4” Hex Posts, Male/Male - E
(2) 5” Hex Posts, Male/Male - F
(2) 4” Hex Post Extensions,
Male/Female - G
(2) 5” Hex Post Extensions,
Male/Female - H
(1) Heavy-Duty, Blow Molded Case
2Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
SAFETY INFORMATION
The following explanations are displayed in this manual, on the labeling, and on all other information
provided with this product:
A
B
D
H
C
EG
F
To order parts and supplies: 800.345.1178 >> eastwood.com 3
READ INSTRUCTIONS
• Thoroughly read and understand these product instructions before
using the Puller.
• Keep these product instructions for future reference.
IMPROPER MOTOR VEHICLE REPAIR WORK
CAN RESULT IN INJURY OR DEATH!
• Performing automotive repair work can cause injury, death and vehicle
accidents. DO NOT attempt to use this tool or begin work without
proper training and a thorough understanding of motor vehicle
mechanical systems.
• Always consult an authorized manufacturer’s service manual or reference
materials on the particular vehicle for the proper procedures before
using this tool.
PINCH AND CRUSH HAZARD!
• This Puller consists of heavy metal components which can present a
hand/finger pinch hazard and cause potentially serious injuries if dropped.
Avoid pinching hands while handling. The use of safety shoes is strongly
recommended. Keep fingers and hands away from moving parts
when operating.
FALL HAZARD!
• Parts may suddenly release while being pulled. Failure to ensure proper
footing can quickly result in a fall which could inflict serious personal
injury or property damage.
EYE INJURY HAZARD!
• Impacting metal components of tool may release chips.
Wear ANSI approved eye protection while using.
SAFETY INFORMATION
4Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com
BEARING/GEAR PULLER ASSEMBLY
FOR BEARING/GEAR PULLING
• Select the Bearing Separator Jaw size (C OR D) as required.
• Measure the distance from the inner surface of the bearing or gear to be pulled and the end of
the shaft it is mounted to.
• Select the set of Posts (E OR F) and Extensions (G OR H) to fit the Bearing Separator Jaws
(C OR D) being used.
• The selected components must be assembled from the Jaws outward.
• Place the halves of the Jaws (C OR D) with the beveled edges around the back of the bearing
or gear to be pulled.
• Draw the halves inward by tightening the nuts on the Jaw Stems.
• Determine whether Post Extensions (G OR H) are needed.
• Thread the ends of the selected Post Extensions (G OR H) (if needed) into the threaded holes
of the Jaws.
• Thread the non-shouldered ends of the Posts (E OR F) into the Post Extensions (G OR H) or
directly into the threaded holes of the Jaws (C OR D).
• Center and place the open ends of the Yoke (A) (with the offset boss facing outward) over the
shouldered ends of the Posts (E OR F).
• Place a washer over the threaded Post ends and against the face of the Yoke (A).
• Thread the Nuts over the exposed Post threads and tighten in place.
• Thread the Pressure Screw (B) into the Yoke (A) as far as necessary to contact the end of
the shaft to pulled against.
• Following the above procedure, the assembly should resemble that in Fig 1 (FIG 1).
C or D
FIG. 1
G or H E or F
A
B
✓
✓
✓
✓
✓
To order parts and supplies: 800.345.1178 >> eastwood.com 5
FOR BEARING/HOUSING SEPARATING
• Select the needed Bearing Separator Jaw size (C OR D) as required (FIG 2).
• Place the halves of the Jaws (C OR D) with the beveled edges around the halves of the bearing
and housing to be separated.
• Draw the halves inward by tightening the nuts on the Jaw Stems.
BEARING/GEAR PULLER OPERATION
FOR BEARING/GEAR PULLING
• Be sure the nuts keeping tension on the Jaw (C OR D) halves are kept tight and the two halves
of the Jaw are drawn in evenly.
• Rotate the Hex on the end of the Pressure Screw (B) slowly and steadily exerting pressure until
the bearing or gear is released from its shaft.
FOR BEARING SEPARATING
• Apply a small amount of a heavy-bodied lubricant on the beveled edges of the Jaws (C OR D).
• Draw the Jaw halves inward by tightening the nuts on the Jaw Stems equally. It is best to
alternate tightening each side with one turn each steadily exerting pressure until the bearing
and housing separates.
C or D
FIG. 2
✓
6Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com
To order parts and supplies: 800.345.1178 >> eastwood.com 7
© Copyright 2016 Easthill Group, Inc. 11/16 Instruction item #31472Q Rev 1
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: techelp@eastwood.com
PDF version of this manual is available online >> eastwood.com/31472manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
US and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: 610.323.6268 eastwood.com
ADDITIONAL ITEMS
#70448 Eastwood 1/2” Twin Hammer Super Mini Air Impact Wrench
#30169 Eastwood Low Profile 2 Ton Aluminum Floor Jack
#31338 1/2” Micrometer Torque Wrench, 30-250 ft/lbs.
Table des matières
Autres manuels Eastwood Outils
Eastwood
Eastwood 20555 Manuel utilisateur
Eastwood
Eastwood 51088 Manuel utilisateur
Eastwood
Eastwood 25304 Manuel utilisateur
Eastwood
Eastwood Elite 64646 Manuel utilisateur
Eastwood
Eastwood 54830 Manuel utilisateur
Eastwood
Eastwood 21302 Manuel utilisateur
Eastwood
Eastwood 32499 Manuel utilisateur
Eastwood
Eastwood 20629 Manuel utilisateur
Eastwood
Eastwood 20269 Manuel utilisateur
Eastwood
Eastwood 32559 Manuel utilisateur
Eastwood
Eastwood 21320 Manuel utilisateur
Eastwood
Eastwood 21489 Manuel utilisateur
Eastwood
Eastwood QST 30 Manuel utilisateur
Eastwood
Eastwood 20556 Manuel utilisateur
Eastwood
Eastwood CONTOUR SCT Manuel utilisateur
Eastwood
Eastwood 20254 Manuel utilisateur
Eastwood
Eastwood VERSA-CUT Manuel utilisateur
Eastwood
Eastwood 20642 Manuel utilisateur
Eastwood
Eastwood 20447 Manuel utilisateur
Eastwood
Eastwood 21566 Manuel utilisateur
