EarthQuake WP6520 Manuel utilisateur

GetEarthquake.com

WP6520 & WP6530 WATER PUMPS

OPERATOR’S MANUAL

OMWP65

R070209

WP6520

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

Page 2 800-345-6007

GetEarthquake.com

Please read and save these instructions.

Read carefully before attempting to as-

semble, install, operate or maintain the

product described. Protect yourself and

others by observing all safety information.

Failure to comply with instructions could

result in personal injury and/or property

damage! Retain instructions for future

reference.

Description

Earthquake Pumps are general use centrifugal

water pumps.

Safety Guidelines

This manual contains information that is very

important to know and understand. This infor-

mation is provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help recognize this

information, observe the following symbols.

DANGER

Danger indicates an imminently hazard-

ous situation which, if not avoided, will

result in death or serious injury.

WARNING

Warning indicates a potentially hazardous

situation which, if not avoided, could result

in death or serious injury.

CAUTION

Caution indicates a potentially hazardous

situation which, if not avoided, may result

in minor or moderate injury.

NOTICE

Notice indicates important information,

that if not followed, may cause damage to

equipment.

GENERAL SAFETY INFORMATION

1. Know the pump application, limitations, and

potential hazards. Read these rules and the

instructions carefully. Failure to follow them could

cause serious bodily injury and/or property dam-

age.

DANGER

Never run engine in an enclosed area. Ex-

haust gases contain deadly poisonous car-

bon monoxide, which has no odor or taste.

WARNING

Do not use to pump ﬂammable or explo-

sive ﬂuids such as gasoline, fuel oil, kero-

sene, etc. Do not use in ﬂammable and/or

explosive atmospheres. Pump should only

be used to pump water. Failure to follow

this warning can result in personal injury

and/or property damage.

2. Observe all safety precautions for the handling

of the fuel.

WARNING

Do not refuel a hot engine. Fuel spilled on

a hot engine could result in a ﬁre or explo-

sion. Do not refuel a running engine.

3. Pump should be located and should rest on a

level solid foundation. Do not suspend pump

by means of the discharge pipe.

NOTICE

Be sure pump is on secure footing so it

doesn't fall over.

4. Do not use torches or apply excessive heat, ﬁre

or ﬂames to this pump as an explosion may

result.

Page 3800-345-6007

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

GetEarthquake.com

5. Before working on the unit, insulate the wire

from the spark plug, disconnect the spark plug

wire and mount it on the grounding clip.

NOTICE

Complete pump and piping system MUST

be protected against below freezing tem-

perature. Failure to do so could cause

serious damage and voids the warranty.

6. Do not run pump dry. Water is required to

lubricate the shaft seal.

7. Pumping chemicals or corrosive liquids with

this pump may shorten the life of the pump

and may be hazardous to the operator.

8. Personal Safety:

a. Wear safety glasses at all times when work-

ing with pumps.

b. Keep work area clean, uncluttered and

properly lighted; replace all unused tools and

equipment.

c. Keep visitors at a safe distance from the

work area.

9. Always use a suction strainer with this pump to

ﬁlter large material.

INSTALLATION

This pump is designed to be self-priming when

installed and operated as speciﬁed below.

1. The pump should be placed as close as pos-

sible to the liquid being pumped. A pump with

20 foot suction lift will not remove water as

quickly as a pump with 5 foot suction lift (Fig-

ure 1).

2. Suction hose and ﬁtting must be airtight.

NOTICE

An air leak in the suction line may prevent

priming of the pump. Use of thread seal-

ant is recommended.

Suction lines must be reinforced hose or rigid

pipe. Non-reinforced hose will collapse due to

the suction created by the pump and prevent

pump from operating.

3. A check valve must be used in the suction line

to maintain the self-priming capability. If no

check valve is used the pump will need to be

primed at the start of each operation. For best

operation, the check valve should be installed

at the intake of the suction line.

4. A suction strainer is required to ﬁlter abrasive

material

5. The discharge hose and ﬁtting should not leak.

A leak in the discharge hose will allow water to

spray out. Water spray could be hazardous.

6. Keep all pipes and hose lines as short and

straight as possible. Long lengths and curves

in the pipes and hose lines will reduce the

pressure the pump develops.

5 ft. suction lift

20 ft.

suction

lift

Figure 1

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

Page 4 800-345-6007

GetEarthquake.com

7. Fill the engine crankcase with oil. Refer to the

engine operating manual for the speciﬁc grade

of oil and amount required.

8. Fill the engine fuel tank with gasoline. Refer to

the engine operating manual for speciﬁc gaso-

line type that is most efﬁcient for this engine.

9. Add water to the priming port on the pump

(See Figure 2). Continue adding water until

the water level is approximately 3 inches from

the top. Install the priming plug. The water

in the pump will create the suction that primes

the pump.

10. Turn fuel valve to 'ON' position.

11. Move choke lever to 'CHOKE' position.

12. Move throttle lever to 'START' position.

13. Pull engine crank until engine starts. Once

engine starts, move choke lever to 'RUN' posi-

tion.

14. The pump will take several minutes to prime.

PIPING

Always place the pump as close as possible to

the liquid being pumped. Keep all pipe and hose

lines as short and straight as possible.

WARNING

Support pump and piping when assem-

bling and after installation. Failure to do

so may cause piping to break, pump to

fail, etc; all of which can result in property

damage and/or personal injury.

All suction connections must be airtight. If the

pump won't prime, check for leaks in the suction

piping or ﬁttings. If ﬂexible suction hose is used

instead of pipe, use reinforced hose with a two

inch inner diameter. Non-reinforced ﬂexible hose

may collapse from the vacuum created as the

pump primes.

Always use a strainer at the end of the suction

pipe or hose. Position strainer so it doesn't be-

come clogged with stones or debris. A suction

line check valve next to strainer is recommended.

Do not use this pump for suction lifts over twenty-

ﬁve feet.

MAINTENANCE

Always shut off the engine, allow the engine to

cool, and remove the spark plug before perform-

ing any maintenance.

During freezing weather, open the drain port and

allow all the water in the pump to drain. This

will prevent damage to the pump when the water

freezes. If the pump will be stored for a month or

more, drain the water from the pump and follow

the engine manufacturer's recommendations for

long-term storage.

The Viper engine is equipped with a low oil shut

off sensor. The engine will shut down and will not

restart if the oil level becomes low.

Priming

Port

Figure 2

Page 5800-345-6007

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

GetEarthquake.com

REGISTRATION

Record your model number and serial number in the space provided

for easy reference. Fill out and mail the registration card located in

your parts packet. Warranty is valid only if your completed registration

card is received by Ardisam, Inc., at time of purchase.

Model Number

Serial Number

Date of Purchase

Place of Purchase

WARRANTY

Earthquake offers a one year limited warranty to be free from defects

in materials and workmanship for the service life of the product not

to exceed twelve consecutive months from the date of purchase.

The engine is covered under a separate warranty provided by the

manufacturer. This warranty applies to the original owner with a

proof of purchase and is not transferable. This warranty applies only

to products which have not been subjected to negligent use, misuse,

alteration, accident or if repairs have been made by anyone outside

our factory. This warranty supersedes all other warranties either ex-

pressed or implied and all other obligations or liabilities on our part.

Ardisam, Inc., does not assume, and does not authorize any other

person to assume for us, any liability in connection with the sale of our

products. Warranty work must be sent directly to Ardisam, Inc. or one

of our authorized service centers and performed by them. To obtain

warranty service and replacement instructions, contact our customer

service department at 800-345-6007 (M-F 8:00am - 5:00pm CST)

or by writing to: Ardisam, Inc., 1690 Elm Street, Cumberland, WI

54829. All items must be shipped prepaid. Ardisam, Inc. will at no

charge, repair or replace, at their discretion, any defective part which

falls under the conditions stated above. Ardisam retains the right to

change models, speciﬁcations and price without notice.

NOTES

___________________________________________

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

Page 6 800-345-6007

GetEarthquake.com

WP6520 PUMP PARTS LIST 2 INCH QTY EA

1 913300 PUMP OUTBOARD CASE 2 INCH 1

2 913347 PUMP INBOARD CASE 2 INCH 1

3 913302 PUMP DISCHARGE FLANGE 2 INCH 1

4 913303 PUMP INLET FLANGE 2 INCH 1

5 913304 PUMP HAND NUT 2 INCH 2

6 913305 PUMP IMPELLER 2 INCH 1

7 913306 PUMP VOLUTE 2 INCH 1

8 913307 PUMP HOSE ADAPTER 2 INCH 2

NS* 913308 PUMP FILTER CONE 2 INCH 1

NS* 913348 PUMP FILTER CAP W/ADPT 2 INCH 1

11 913310 PUMP PRIMER CAP 2

12 913311 PUMP CHECK FLAP 2 INCH 11

13 913312 PUMP GASKET DISCHARGE 2 INCH 11

14 913313 PUMP GASKET INLET 2 INCH 12

15 913314 PUMP CASE O-RING 2 INCH 11

16 913340 PUMP VOLUTE O-RING 2 INCH 11

17 913315 PUMP PRIMER CAP GASKET 12

18 913349 PUMP RUBBER #8 WASHER 14

19 913317 PUMP MECHANICAL SEAL 2 INCH 21

20 913318 PUMP ROTATING SEAL 2 INCH 21

NS* 913319 PUMP HOSE CLAMP 2 INCH 3

24 64595 BOLT M8 X 20 HHFCS 4

25 64595 BOLT M8 X 20 HHFCS 4

26 64617 BOLT M8 X 25 HHFCS 4

27 64617 BOLT M8 X 25 HHFCS 4

1SOLD ONLY AS 913350 - PUMP GASKET SERVICE KIT 2 INCH

2SOLD ONLY AS 913346 - PUMP SEAL SERVICE KIT 2 INCH

* NS = not shown

WP6530 PUMP PARTS LIST 3 INCH QTY EA

1 913320 PUMP OUTBOARD CASE 3 INCH 1

2 913321 PUMP INBOARD CASE 3 INCH 1

3 913322 PUMP DISCHARGE FLANGE 3 INCH 1

4 913323 PUMP INLET FLANGE 3 INCH 1

5 913324 PUMP HAND NUT 3 INCH 2

6 913351 PUMP IMPELLER 3 INCH 1

7 913326 PUMP VOLUTE 3 INCH 1

8 913327 PUMP HOSE ADAPTER 3 INCH 2

NS* 913352 PUMP FILTER CONE 3 INCH 1

NS* 913353 PUMP FILTER CAP W/ADPT 3 INCH 1

11 913310 PUMP PRIMER CAP 2

12 913330 PUMP CHECK FLAP 3 INCH 31

13 913331 PUMP GASKET DISCHARGE 3 INCH 31

14 913355 PUMP GASKET INLET 3 INCH 32

15 913333 PUMP CASE O-RING 3 INCH 31

16 913341 PUMP VOLUTE O-RING 3 INCH 31

17 913315 PUMP PRIMER CAP GASKET 32

18 913349 PUMP RUBBER #8 WASHER 31

19 913334 PUMP MECHANICAL SEAL 3 INCH 41

20 913335 PUMP ROTATING SEAL 3 INCH 41

NS* 913342 PUMP SPRING MECHAN. SEAL 3 IN 41

NS* 913336 PUMP HOSE CLAMP 3 INCH 3

24 913357 BOLT M10 X 20 HHFCS 3

25 913358 BOLT M10 X 25 HHFCS 4

26 913358 BOLT M10 X 25 HHFCS 4

27 913339 BOLT M8 X 65 HHFCS 4

3SOLD ONLY AS 913343 - PUMP GASKET SERVICE KIT 3 INCH

4SOLD ONLY AS 913359 - PUMP SEAL SERVICE KIT 3 INCH

* NS = not shown

Page 7800-345-6007

OPERATOR INSTRUCTIONS AND PARTS

WP6520 & WP6530 Water Pumps

GetEarthquake.com

Earthquake, Division of Ardisam, Inc.

1690 Elm Street

Cumberland, Wisconsin 54829

800-345-6007 · Fax (715) 822-2223

E-mail: [email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels EarthQuake Pompe à eau

EarthQuake

EarthQuake WP4310 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur