Dynabrade Dynangle 14200 Manuel utilisateur

Disassembly Instructions - 0.7 hp. Dynangle Air Motor

Models: 14200

Important: Use these instructions along with the tool parts page or manual.

Notice: Shut off the air supply and depress throttle lever to deplete the remaining air.

• Carefully disconnect the tool from the air supply hose. • Remove the cover and the abrasive

belt. • Use the Special Repair Tools designed for the disassembly and assembly of this motor.

Motor Disassembly:

1. Use a 1/8" hex key to loosen the 95530 Screw.

Remove the motor from the belt housing.

1/8" hex key

1/8" Hex Key

2. Use a 19 mm wrench to hold the motor spindle. By hand, or with groove pliers, grasp the

drive wheel and remove it. Turn counterclockwise.

19 mm Wrench

3. Carefully fasten the 01739 Housing in a vise with aluminum or bronze jaws so that the

spindle is pointing up.

Use a 1-1/2" crowfoot wrench to remove the 01748 Exhaust Cover.

Turn counterclockwise.

Remove the 01744 Silencer.

1-1/2" crowfoot wrench

Pull the motor out of the housing.

4. Fasten the 96346 Bearing Separator (2") around the 01028 Cylinder. Place the separator

and the motor in the 96232 Arbor Press (#2) so that the rotor spindle is pointing down.

Use a 5/32" or 4 mm diameter flat end drive punch to push the rotor out of the 02649

Bearing.

96346 Bearing Separator

5. Use the 96213 Bearing Removal Tool and the arbor press to remove the 02649 Bearing

from the rear bearing plate.

96346 Bearing Separator

96213 Bearing Removal Tool

6. Fasten the 55025 Rotor in the vise with aluminum or bronze jaws and use an adjustable

wrench to remove the 01708 Rotor Nut. Turn counterclockwise.

Remove the 01007 Bearing, 01008 Bearing Plate, shims, and 01010 Spacer.

Motor Disassembly Completed.

Clean and inspect parts before assembling.

Assembly Instructions - 0.7 hp. Dynafile III Air Motors

Motor Assembly:

1. Install the 01010 Spacer onto the rotor.

Install .003" (~0.80 mm) shim thickness into the 01008 Front Bearing Plate.

Install the 01007 Bearing into the front bearing plate.

Install the bearing and plate onto the rotor.

.003" (~0.80 mm)

shim thickness

01010 Spacer

2. By hand, install the 01708 Rotor Nut. Pull the front bearing plate forward to take movement

out of the bearing. Check the clearance between the rotor and plate.

Use a .001" (~0.03 mm) thick feeler gauge. Notice: The clearance should be

.001"-.0015" (~0.03-0.04 mm). If the rotor/plate clearance needs adjustment, repeat

steps 1 and 2. Remove or add shims as required.

.001"-.0015"

(~0.03-0.04 mm)

3. Use a 19 mm crowfoot and a torque wrench to tighten the 01708 Rotor Nut.

(T to 17 N•m/~150 in. lbs.)

T to 17 N•m/~150 in. lbs.

Autres manuels Dynabrade Sander

Dynabrade

Dynabrade 58410 Manuel utilisateur

Dynabrade

Dynabrade 10390 Guide de l'utilisateur

Dynabrade

Dynabrade 18066 Mode d’emploi

Dynabrade

Dynabrade Dynorbital 57610 Manuel utilisateur

Dynabrade

Dynabrade 10710 Manuel utilisateur

Dynabrade

Dynabrade Dynafine 57902 Manuel utilisateur

Dynabrade

Dynabrade 10787 Mode d’emploi

Dynabrade

Dynabrade Dynabug 57810 Manuel utilisateur

Dynabrade

Dynabrade 52503 Instructions d'installation

Dynabrade

Dynabrade 58441 Manuel utilisateur

Dynabrade

Dynabrade Dynalocke 58430 Manuel

Dynabrade

Dynabrade 52413 Instructions d'installation

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Manuel

Dynabrade

Dynabrade Dynabug 57811 Manuel utilisateur

Dynabrade

Dynabrade 50304 Manuel utilisateur

Dynabrade

Dynabrade Dynabug Model T 10485 Guide de l'utilisateur

Dynabrade

Dynabrade Dynorbital-Spirit 59000 Mode d’emploi

Dynabrade

Dynabrade Dynabug II 58500 Mode d’emploi

Dynabrade

Dynabrade 50371 Instructions d'installation

Dynabrade

Dynabrade 58050 Instructions d'installation

Dynabrade

Dynabrade Dynorbital Supreme 57655 Manuel utilisateur

Dynabrade

Dynabrade 53521 Mode d’emploi

Dynabrade

Dynabrade 57900 Mode d’emploi

Dynabrade

Dynabrade 300CE Mode d’emploi

Manuels Sander populaires d'autres marques

Oliver

Oliver 6305 Manuel utilisateur

Jet

Jet 22-44 Pro-3 Manuel de service

Makita

Makita M9204 Manuel

Makita

Makita M9204 Manuel utilisateur

Craftsman

Craftsman 351.215131 Manuel utilisateur

Clarke

Clarke Woodworker CBS1-5B Mode d’emploi

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuel utilisateur

Nitto Kohki

Nitto Kohki BB-20 Manuel utilisateur

Ferm

Ferm FEOS-135 Manuel utilisateur

Unior

Unior 1510 Manuel utilisateur

stayer

stayer ls1200 Manuel utilisateur

Jet

Jet JSG-96 Manuel de service

Parkside

Parkside PDS 290 B2 Manuel utilisateur

Status

Status XPA Series Manuel utilisateur

Clarke

Clarke EZ Sand Manuel utilisateur

Craftsman

Craftsman 113.22521 Manuel utilisateur

Craftsman

Craftsman 113.225831 Manuel utilisateur

CLAS

CLAS OP 1429 Manuel utilisateur