Duronic Si2 Manuel utilisateur
Si2 - Travel Steam Iron
PLEASE READ ALL THE INSTRUCTIONS BEFORE USE
2
3
English Manual
Manuel d’utilisation en français
Gebrauchsanleitung auf Deutsch
Manual de Instrucciones en Español
Manuale D’istruzioni In Italiano
Instrukcja obsługi. Polski
Gebruikershandleiding Nederlands
5
13
21
29
37
45
53
Contents
4
5
English Manual
6
Features and Specications
Components
MODEL POWER VOLTAGE
RATING
WATER TANK
CAPACITY
Si2 375W 220-240V ~
50/60Hz
40ml to max line,
50ml to full
1. Sole plate
2. Standing heels
3. Body
4. Power cable
5. Handle
6. Control dial
7. Water tank
• Steam burst: activated by press
button
• Water tank capacity: 35ml
• Temperature range: 65-230°c
• Soleplate size: 7.3cm squared
8. Water inlet
9. Steam burst button
10. Power indicator light
11. Water ller jug
12. Brush attachment
13. Storage bag
• Power light indicator: red
• Self-standing design
• Size: L33 x W76 xH78 mm
• Weight: 495g
• Power cable length: 190cm
12
13
11
1
2
3
4
5
6
7 8 9
10
7
Safety Instructions
PLEASE READ THIS MANUAL CAREFULLY AND RETAIN FOR FUTURE
REFERENCE
• This appliance is for light or occasional indoor/household use only. This
iron is not intended for professional laundry services.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be closely supervised at all times to ensure that they do
not play with the appliance.
• Do not operate this appliance if the power cable or plug is damaged. If
either is damaged return it to Duronic for service or repair by professional
technician.
• Please ensure the mains power supply is 220-240V ~ 50/60Hz
• Never try to replace the parts or repair the appliance by yourself.
• To reduce the risk of electric shock, never operate this product with wet
hands, spill liquid on the appliance or submerge it in water or any other
liquid.
• Do not place the appliance on or near a hot gas or on a heated oven.
• Do not let the power cable hang over the edge of a table or counter or
touch a hot surface.
• Pay close attention to the iron whilst in use. The iron must not be left
unattended while it is connected to the mains socket.
• Ensure that the iron is switched off and unplugged from the electrical
mains socket and fully cooled down before removing the brush
attachment.
• Do not use any attachments which are not listed in this manual.
• Always hold the iron by the handle. Keep the hot soleplate away from body
parts and heat sensitive objects.
8
• Do not turn the iron upside down; there may be hot water in the water
tank.
• Do not leave water in the water tank when not in use - this can corrode
and damage the soleplate.
• Water will drip out of the iron if the temperature dial is not set.
• Keep the appliance well away from surfaces and objects that can be
damaged by heat.
• Ensure there is adequate space to operate the iron.
• When not ironing, do not leave the iron face down. Stand it upright on its
heel, on a level heatproof surface.
• Use this iron only with a purpose-built ironing board.
• Observe all of the ironing instructions and ironing temperature dot settings
given by the garment manufacturer. These guidelines are normally on the
label/s inside the garment.
• Always ensure the water lling does not exceed the MAX mark.
• Always unplug the iron when relling the water reservoir.
• Do not iron buttons or fasteners. This could damage the iron.
• During operation do not use when the light is on. When the light turns off
the iron has reached the correct temperature.
• Do not iron directly onto synthetic fabric - instead iron the fabric inside out
or with the synthetic fabric covered by other material to protect it.
9
Ironing Temperatures
Garment Label Fabric Type Thermostat
Regulation
Synthetic Low temperature
Silk-wool Medium temperature
Cotton-linen High temperature
Fabric not to be ironed
How to Use
FILLING THE IRON
1. Make sure the iron is switched off and unplugged from the mains socket.
2. Fill the water jug with fresh water from the tap. If you live in a hard water
area, it is advisable to use distilled water. Avoid using water containing
softeners, perfumes or additives.
3. Open the water inlet cap on the top of the iron and slowly pour the water in
from the jug.
4. Close the cap.
USING THE IRON
1. Plug the cable into the mains socket and switch on.
2. Check the label inside the garment to nd out what heat setting you
require for the fabric.
3. Turn the control dial to the temperature you require.
4. Stand the iron on its heel and wait for it to heat up. When it has reached
the set temperature, the indicator light will go off.
10
5. Iron your garment/fabric as you normally would.
6. If the water level goes low and you haven’t yet nished ironing, unplug
the iron and rell it using the water jug provided. Then plug it back in and
commence with ironing.
7. When you have nished ironing, turn the control dial to the MIN position.
Unplug it from the mains socket.
8. Stand the iron on its heel and leave to cool down. Once cool, empty the
water tank.
9. To store away, wrap the cable around the iron. Store away using the bag
provided.
STEAM BURST FUNCTION
The steam burst function is mainly used for thick materials or fabrics with
stubborn creases.
If you want to use the steam burst function, you will need to set the control dial
to the MAX setting.
Press the steam burst button a few times before using the iron at each ironing
session. This will clean the steam vents.
Place the iron onto the fabric and press the steam push button to release a
powerful burst of steam. Wait a few seconds for the steam to penetrate the
fabric before pressing the button again.
Table des matières
Langues :
Autres manuels Duronic Fer
