DURKOPP ADLER 8967 Manuel utilisateur

Contents: Page:

Part 2: Installation Cl. 8967

1. General Information

1.1 Machine Operation without Material . . . . . . . . . . . . . . . . . . . . 3

1.2 Table Tops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. Table Top, Completing and Screwing on . . . . . . . . . . . . . . . . 7

4. Connecting the Sewing Drive to the Table Top

4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.2 Drive Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.3 Voltage Compensation Motor/ Machine Head . . . . . . . . . . . . . . . 8

4.4 Attaching the Pedal and Rod . . . . . . . . . . . . . . . . . . . . . . . . 9

4.5 Electrical Connection of the Motors . . . . . . . . . . . . . . . . . . . . . 9

5. Attaching the Machine Head

5.1 Mounting the Sewing Head, Establishing the Voltage Compensation

Positioning the V-belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5.2 Attaching the Belt Guard,

Mounting and Setting the Synchronizer . . . . . . . . . . . . . . . . . . 11

5.3. Connecting the Solenoid Valve Strip . . . . . . . . . . . . . . . . . . . . 12

6. Connecting the Compressed Air Maintenance Unit . . . . . . . . . . 13

7. Filling Oil and Readying the Machine for Operation . . . . . . . . . . 14

8. Conducting the Sewing Test . . . . . . . . . . . . . . . . . . . . . . . . 14

1. General Information

Attention!

The mains voltage and the nominal voltage listed on the

motor identification plate must be the same.

All work on the electronics is to be conducted only by au-

thorized personnel and with the mains plug disconnected.

Please observe all safety instructions!

Installation is to be conducted according to the following

instructions. All necessary parts are to be found in the en-

closed package.

1.1 Machine Operation without Material

Attention!

First arrest the pressure feet in the raised position and

set the shortest pressure foot stroke.

1.2 Table Tops The cutouts in self-made table tops must have the dimen-

sions shown in the sketches on pages 4 and 5.

The table tops must have the necessary load capacity

and firmness.

2. Frame Assembly

–Assemble the frame parts as shown and take care

that all feet touch the floor.

–Adjust the screws on the frame foot at the right back

accordingly for this.

3. Table Top, Completing and Screwing on

Underside of the Table Top:

- Screw on the cable duct 4 and the holder 5 for strain re-

liever

- Screw on main switch 2

- Screw on the sewing light transformer 1, if supplied

- Lay the electric wiring in the cable duct and to the motor

- Screw on the drawer 3 with mounting

- Screw on table top support plate 6 by frame MG56-2

- Screw the table top onto the frame with B8 x 35 wood

screws.

123

4. Connecting the Sewing Drive to the Table Top

4.1 General Different drive and connections packages are available

for the machine.

The drive package consists of:

Motor, motor protection switch with wiring, belt, belt pul-

ley.

The connectios package contains all wiring between the

motor and the sewing head.

The direct current drive available for this machine is ope-

rated by a "monophase alternating voltage". Therefore,

with multiple machines, the connections must be uniform-

ly distributed to the individual phases of the mains supply

(3 phase). Otherwise, this could lead to an overload of

the individual phases.

Attention!

If the electronics are not supplied by Dürkopp Adler, then

manufacture and testing is to be conducted to EN 60204-

3-1/JEC 204-3-1.

4.2 Drive Mounting

–Screw the drive with its base to the table top. Hereby

screw the 3 hex head M8 x 35 screws with washers

into the nuts in the table top.

–Fasten the V-belt pulley to the motor shaft

–Check the connections on the motor terminal board

and correct if necessary.

The arrangement must be appropriate to the mains

voltage.

4.3 Voltage Compensation Motor/ Machine Head

–Screw the green-yellow connecting cable found in

the enclosed package onto the motor base. It serves

to conduct the machine head static charge to ground

via the motor.

4.4 Attaching the Pedal and Rod.

For ergonomic reasons the lateral direction of the pedal is

to be aligned centered to the needle. Set the rod so that

the pedal has an incline of 10°.

4.5 Electrical Connections of the Motors

Please see the wiring diagrams enclosed in the drive

package for the necessary technical connections data.

5. Attaching the Machine Head

5.1 Mounting the Sewing Head, Establishing the Voltage

Compensation, Positioning the V-belt

–Mount the sewing head and fasten with three M8 x

95 Allan screws with washers and nuts.

–Establish the voltage compensation.

Screw the enclosed single-wire cable 1 to the sewing

head.

–Positioning the V-belt.

–Set the V-belt tension.

By swinging the motor, tension the V-belt so that it

can be pressed in at its center by about 10 mm

without great effort.

–Screw on the motor belt guard.

Set the cams so that the belt cannot slide out of the

V-belt pulley when the sewing machine is swung to

the back.

Autres manuels pour 8967

Table des matières

Autres manuels DURKOPP ADLER Machine à coudre

DURKOPP ADLER

DURKOPP ADLER 911-210-3020-10 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 767 - Mode d'emploi

DURKOPP ADLER

DURKOPP ADLER 745-34 - Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER M-TYPE 667 Mode d'emploi

DURKOPP ADLER

DURKOPP ADLER 906 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 911-211 Mode d'emploi

DURKOPP ADLER

DURKOPP ADLER 238 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 745-34 - Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 867 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 745-35-10 S Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 275 Series Mode d’emploi

DURKOPP ADLER

DURKOPP ADLER beisler 2112-5 Mode d'emploi

DURKOPP ADLER

DURKOPP ADLER 697 Manuel de la liste des pièces

DURKOPP ADLER

DURKOPP ADLER 911-210 Manuel d'utilisation

DURKOPP ADLER

DURKOPP ADLER 1265-5 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 556 Manuel d'exploitation et d'entretien

DURKOPP ADLER

DURKOPP ADLER 580 - Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 272-160362 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER M-Type 869 Mode d'emploi

DURKOPP ADLER

DURKOPP ADLER class 743-221 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 4182i-1 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 969 ECO Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 540 - 100 Manuel utilisateur

DURKOPP ADLER

DURKOPP ADLER 878-M PREMIUM Manuel utilisateur

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Singer

Singer 2517 Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

Singer

Singer 148-5 Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Singer

Singer 15-91 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Singer

Singer 6038 Manuel utilisateur

Singer

Singer 413K Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur