Duratool D03046 Instructions de montage

OPERATOR’S INSTRUCTION

MANUAL

DIGITAL MULTIMETER

Model: D03046 and D03047

- 2 -

Warning

To avoid possible electric shock or personal

injury, and to avoid possible damage to the Meter or

to the equipment under test, adhere to the following

rules:

Before using the Meter inspect the case. Do

not use the Meter if it is damaged or the case

(or part of the case) is removed. Look for

cracks or missing plastic. Pay attention to

the insulation around the connectors.

Inspect the test leads for damaged insulation

or exposed metal. Check the test leads for

continuity.

Do not apply more than the rated voltage, as

marked on the Meter, between the terminals or

between any terminal and grounding.

The rotary switch should be placed in the right

position and no any changeover of range shall

be made during measurement is conducted to

prevent damage of the Meter.

When the Meter working at an effective voltage

over 60V in DC or 30V rms in AC, special care

should be taken for there is danger of electric

shock.

Use the proper terminals, function, and range

for your measurements.

Do not use or store the Meter in an

environment of high temperature, humidity,

explosive, inflammable and strong magnetic

field. The performance of the Meter may

deteriorate after dampened.

When using the test leads, keep your fingers

behind the finger guards.

Disconnect circuit power and discharge all

- 3 -

high-voltage capacitors before testing

resistance, continuity, diodes or hFE.

Replace the battery as soon as the battery

indicator appears. With a low battery,

the Meter might produce false readings that

can lead to electric shock and personal injury.

Remove the connection between the testing

leads and the circuit being tested, and turn the

Meter power off before opening the Meter

case.

When servicing the Meter, use only the same

model number or identical electrical

specifications replacement parts.

The internal circuit of the Meter shall not be

altered at will to avoid damage of the Meter

and any accident.

Soft cloth and mild detergent should be used

to clean the surface of the Meter when

servicing. No abrasive and solvent should be

used to prevent the surface of the Meter from

corrosion, damage and accident.

The Meter is suitable for indoor use.

Turn the Meter power off when it is not in use

and take out the battery when not using for a

long time. Constantly check the battery as it

may leak when it has been using for some time,

replace the battery as soon as leaking appears.

A leaking battery will damage the Meter.

General Specifications

Max display: LCD 3 ½ digits (1999 count) 0.5” high

Polarity: Automatic, indicated minus, assumed plus.

Measure method: double integral A/D switch

implement

- 4 -

Sampling speed: 2 times per second

Over-load indication: “1” is displayed

Operating Environment: 0℃~40℃, at <80% RH

Storage Environment: -10℃~50℃, at <85% RH

Power: 9V NEDA 1604 or 6F22

Low battery indication: “ ”

Static electricity: about 4mA

Product Size: 126 x 70 x 26mm

Product net weight: 108g (including battery)

LCD

RANGE

swit

10A jack

VΩmA jack

COM jack

hFE

socket

- 5 -

Series Multimeters Function Table

Technical Specifications

Accuracies are guaranteed for 1 year, 25℃ ± 5℃

less than 80%RH

DC VOLTAGE

RANGE RESOLUTION ACCURACY

200mV 100uV ±(0.5% of rdg + 3D)

2000mV 1mV

20V 10mV

200V 100mV

500V 1V ±(1.0% of rdg + 5D)

±(0.8% of rdg + 5D)

OVERLOAD PROTECTION: 220V rms AC for

200mV range and 500V DC or 500V rms for all

ranges.

AC VOLTAGE

RANGE RESOLUTION ACCURACY

200V 100mV

500V 1V ±(2.0% of rdg +10D)

RESPONSE: Average responding, calibrated in

rms of a sine wave.

FREQUENCY RANGE: 45Hz ~ 450Hz

OVERLOAD PROTECTION: 500V DC or 500Vrms

for all ranges.

- 6 -

AUDIBLE CONTINUITY

OVERLOAD PROTECTION: 15 seconds maxi-

mum 220 V rms.

DC CURRENT

RANGE RESOLUTION ACCURACY

200uA 100nA

2000uA 1uA

20mA 10uA

200mA 100uA ±(2.0% of rdg +2D)

5A 10mA ±(2.0% of rdg +10D)

±(1.8% of rdg +2D)

OVERLOAD PROTECTION: F0.5A/250V and

F5A/250V fuse

MEASURING VOLTAGE DROP: 200mV

RESISTANCE

RANGE RESOLUTION ACCURACY

200Ω 0.1Ω ±(1.0% of rdg +10D)

2000Ω 1Ω

20KΩ 10Ω

200KΩ 100Ω

2000KΩ 1KΩ

±(1.0% of rdg +4D)

MAXIMUM OPEN CIRCUIT VOLTAGE: 3V.

OVERLOAD PROTECTION: 15 seconds

maximum 220Vrms.

TEMPERATURE (with K-TYPE PROBE)

RANGE RESOLUTION ACCURACY

-40℃to

150 ℃±(1.0% + 4)

150℃to

1370 ℃±(1.5% + 15)

1℃

OPERATING INSTRUCTIONS

DC & AC VOLTAGE MEASUREMENT

1. Connect red test lead to “VΩmA” jack, Black

lead to “COM” jack.

2. Set RANGE switch to desired VOLTAGE

position, if the voltage to be measured is not

known beforehand, set switch to the highest

range and reduce it until satisfactory reading is

obtained.

3. Connect test leads to device or circuit being

measured.

4. Turn on power of the device or circuit being

measured voltage value will appear on Digital

Display along with the voltage polarity.

DC CURRENT MEASUREMENT

1. Connect red lead to “VΩmA”. and black lead to

“COM”

(for measurements between 200mA and

5A connect red lead to “5A” socket)

- 7-

2. Set RANGE switch to desired DCA position.

3. Open the circuit to be measured, and connect

test leads IN SERIES with the load in

with current isto measure.

4. Read current value on Digital Display.

5. Additionally, “5A”function is designed for

intermittent use only. Maximum contact time of

the test leads with the circuit is10 seconds,

with a minimum intermission time of 15

minutes between tests.

RESISTANCE MEASUREMENT

1. Connect red lead to “VΩmA”. Connect black

lead to “COM”.

2. Set RANGE switch to desired Ωposition.

3. If the resistance being measured isconnec-

ted to a circuit, turn offpower and discharge all

capacitors before measurement.

4. Connect test leads to circuit being measured.

5. Read resistance value on Digital Display.

DIODE MEASUREMENT

1. Connect red lead to “VΩmA”.Connect black

lead to “COM”.

2. Set RANGE switch to “ ”position.

3. Connect the red test lead tothe anode of the

diode to be measured and black test lead to

cathode.

4. The forward voltage drop in mV will be

displayed. Ifthe diode is reversed, figure “1”

will be shown.

- 8-

TRANSISTOR hFE MEASUREMENT

1. Set RANGE switch to the hFE position.

2. Determine whether the transistor is PNP of

NPN type and locate the Emitter, Base and

Collector leads. Insert the leads into the proper

holes of the hFE Socket.

3. The meter will display the approximate hFE

value at the condition of base current 10μA

and VCE2.8V.

AUDIBLE CONTINUITY TEST

1. Red lead to “VΩmA”, Black lead to “COM”.

2. RANGE switch to “ ” position.

3. Connect test leads to two points of circuit to

be tested. If the resistance is lower then 30Ω

±20Ω, the buzzer will sound.

BATTERY AND FUSE REPLACEMENT

Fuse rarely need replacement and blow almost

always as a result of operator error.

If “ ”appearsin display, itindicates that the

battery should be replaced.

To replace battery &Fuse (F500mA/250V for mA

terminal and F5A/250V for 5A terminal)remove

the 2 screws inthe bottom ofthe case, simply

remove the old, and replace with a new one. Be

careful to observe polarity.

- 9-

- 10 -

Operator’s instruction manual

Set of test leads

Gift box

TP01 K-type thermoelectric couple

(DT830C & DT838 only)

9-volt battery, NEDA 1604 6F22 type.

Made in China

www.premierfarnell.co.uk

WARNING

READ AND UNDERSTAND THIS MANUAL

BEFORE USING THE INSTRUMENT.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF

ELECTRICAL & ELECTRONIC EQUIPMENT.

When this product has reached the end of its life it must be treated as

Waste Electrical & Electronics Equipment (WEEE). Any WEEE

marked products must not be mixed with general household waste, but

kept separate for the treatment, recovery and recycling of the

materials used. Contact your local authority for details of recycling

schemes in your area.

ACCESSORIES

Autres manuels pour D03046

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Duratool Multimètre

Duratool

Duratool D03125 Manuel utilisateur

Duratool

Duratool D03131 Manuel utilisateur

Duratool

Duratool D03046 Manuel utilisateur

Duratool

Duratool D03143 Manuel utilisateur

Duratool

Duratool D03124 Manuel utilisateur

Duratool

Duratool D03122 Manuel utilisateur

Duratool

Duratool D03143 Manuel utilisateur

Duratool

Duratool D03127 Manuel utilisateur

Duratool

Duratool D03305 Manuel utilisateur

Duratool

Duratool D03124 Manuel utilisateur

Duratool

Duratool D03145 Manuel utilisateur

Duratool

Duratool D03126 Manuel utilisateur

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Elenco Electronics

Elenco Electronics CM-1555 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Amprobe

Amprobe Hexagon 60 Manuel utilisateur