Durafly BRAVADO Manuel utilisateur

Features of the Bravado

Specications

Examine your kit carefully

1. ‘AirCore’ construction resulting in both a lightweight, yet strong structure.

2. Powerful set-up as standard for hardcore 3D and aerobatic performance.

3.Quick and easy assembly with minimum parts count.

4. Clean airframe design with easy battery access and generously sized control surfaces.

5. Made from durable and easy to maintain EPO foam and with spare parts readily available.

Wingspan: 1000mm ( 39.4 in.)

Flying Weight: 700-780g (1.5 -1.7lbs)

Motor: 2814 Kv1000

ESC: 40 Amp

Servo: 4 x Turnigy TG9d 9g digital servo’s

Radio：4/more channel

Receiver: 4/more channel

Battery: 3 cell 1000-1300mah lipo 25c min (required)

Prop: 11x

Recommended Environment: Outdoor/large indoor area.

Assembly Time: Less than 1 Hour

Duray model kits are subject to QC checks throughout production, and we sincerely hope that

you are completely satised with the contents of your kit. However, before assembling, we ask that

you check all parts against the parts list. If you are missing any parts, please contact Customer

Services via hobbyking.com. Also check for any damage to the any item within the box. Your model

has travelled a long way, and in some case could have sustained some damage. If you feel the

damage is beyond ressonable repare, please contact CS.

Please note:

We are constantly working on improving our models, therefore every model is subject to change

without notice.

This is a sophisticated hobby product and is NOT a toy. It must always be operated with caution,

common sense and some basic mechanical ability. This manual provides instructions as the the

assembly, safe opperation and maintainence of this hobby product. It is highly reccommneded that

you follow and read fullythe instructions and warnings stated in this manual including, safety,

assembly, set-up and ying guidelines in order to operate this product correctly and avoid damage

or serious injury.

Do not y under the conditions below

Foam parts included in the packing

Cautions for ying

Note for Storage

Tools:

•Strong winds (more than 20pmh)

•Other storm like conditions

•Area close to high voltage wires

•Area with high density population

•Never leave you ight battery installed in the model when storing.

•If hanging the model, ensure the control surfaces are not taking the weight of the model.

•Store away from direct sunlight and ideally at room temperature.

•Secure your model for storage incase it moves and gets damaged.

2. Wing

5. Winglet

8. Canopy

3. Left aileron

6. Rudder

9. Landing gear slice

1. Fuselage

4. Right aileron

7. Rudder bolt

10.Stabilizer

While parks make excellent ying areas, make sure you have permission to y there and follow safety

guidelines set by local authorities.

Required: Scissors, Balsa knife, Combination pliers, Screwdriver, Quick-dry glue

14 21

16. Tail wheel

17. 1155 propeller

18. Rudder pushrod (φ1.2 piano wire)

19. Elevator pushrod (φ1.2 piano wire)

20. Aileron pushrod (φ1.2 piano wire)

21. Screw (M3*8)

11.Landing gear

12. Spinner

13. Screw (M4*30)

14. Screw (M2*5)

15. Adjustor

Parts included in the packing

Assembly steps

1. Aseembly begins with the wing (2) and fuselage (1). Incert the wing panel into the slot in the

fuselage and glue in place. Insure that distance A is equal to B.

2. Hinges (4 for each side) can now be glued into the pre-cut slots of the trailing edge of the wing

(2). Once dryed you can then glue the ailerons(3&4) to the hinges.

4. The horizontal tail (17)can now be glued in place at the rear of the fusealge asr shown.

Ensure distances E and F are equal and that the tail is horizontally level.

3. Insert the fuselage winglet (5) into the upper fusealge slot and glue in place.

Ensure distance C is equal to D.

5. Place vertial trailing edge insert (7) into pre-cut slot at the rear of fuselage, then x with glue.

6. Connect Z bend (18) to servo control horn on rudder (6), then push pushrod into pushrod tube.

Fuselage Assembly

18 6

7. Glue 4 hinges into the rudder (6) then glue the rudder to the vertical tail (1) as shown below.

8. With the rudder in place the landing gear (11) can now be installed. Locate the supplied

M4x25mm bolts (13) and secure to the fuselage (1) using a screw driver as shown.

9. Once the landing gear (11) is secured, the gear foam cover (12) can be installed as shown with just

a small spot of glue.

11. Install your 9g servo’s of choice into the molded pockets on the underside of the wing by guiding the

wires through into the center of the fuselage and securing in place with some glue as shown below.

14 16

10. Locate the tail wheel assembly and install as detailed below using the supplied M2x5mm screws.

KIT ONLY

12. Glue the aileron control horn in place and connect the Z bend push rods (20) as shown. Ensure that your

servo horns are at 90 degree’s to the wing at this stage.

13. Your 9g rudder and elevator servo of choice can now be glued in place in the pre-molded pockets on

either side of the rear fuselage. NOTE, you must ensure your servo leads are long enough to reach the front

of the model, you may need to add extension leads so please check.

KIT ONLY

Table des matières

Autres manuels Durafly Jouet

Durafly

Durafly Spitfire Mk1a Manuel utilisateur

Durafly

Durafly GOBLIN Manuel utilisateur

Durafly

Durafly EDGE 540 V3 Manuel utilisateur

Durafly

Durafly SUPERMARINE SPITFIRE MK24 V2 Manuel utilisateur

Durafly

Durafly Spitfire MK2A Plug and Fly 1100mm... Manuel utilisateur

Durafly

Durafly EXCALIBUR Manuel utilisateur

Durafly

Durafly ME-163 Manuel utilisateur

Durafly

Durafly Ugly Stick Manuel utilisateur

Durafly

Durafly TUNDRA V2 Manuel utilisateur

Durafly

Durafly Bonanza Manuel utilisateur

Durafly

Durafly Auto-G2V2 Manuel utilisateur

Durafly

Durafly BF-110 Manuel de la liste des pièces

Durafly

Durafly Tomahawk Manuel utilisateur

Durafly

Durafly ZEPHYR V-70 EDF-EPO Manuel utilisateur

Durafly

Durafly AUTO-G2 Manuel utilisateur

Durafly

Durafly Das Ugly Stik Manuel utilisateur

Durafly

Durafly ME-163 V2 Manuel utilisateur

Durafly

Durafly Micro Tundra PNF Manuel utilisateur

Durafly

Durafly Curtiss P-40N Manuel utilisateur

Durafly

Durafly SlowPoke Manuel utilisateur

Durafly

Durafly Sky Mule Manuel utilisateur

Durafly

Durafly Messerschmitt BF.109E-4 Manuel utilisateur

Durafly

Durafly EFXTRA Manuel utilisateur

Durafly

Durafly P-51D OLD CROW Manuel de la liste des pièces

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur