DTS XR250 WASH Manuel utilisateur

XR250

Wash

Show division

XR250

Wash

Le informazioni contenute in questo documento sono state attentamente redatte e controllate.

Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e

questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo

consenso scritto della DTS .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o

di design a ciascun proprio prodotto. DTS non assume alcuna responsabilità sull’uso o

sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be

copied, photocopied or reproduced, in part or completely, without prior written consent from DTS.

DTS reserves the right to make any aesthetic, functional or design modifications to any of its

products without prior notice. DTS assumes no responsibility for the use or application of the

products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou

partiellement, sans le consentement préalable de DTS.

DTS se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles

ou de design, sans préavis, à chacun de ses produits. DTS décline toute responsabilité sur l'utilisation

ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales

inexactitudes. Todos los derechos han sido reservados y este documento no puede ser

copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorizaciónescrita de DTS.

DTS se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. DTS no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los productos

o de los circuitos descritos.

XR250

WASH

INDEX:

XR250

WASH

1- TECHNICAL FEATURES Pg. 1

2- IMPORTANT SAFETY INFORMATION Pg. 2

3- MOUNTING THE LAMP Pg. 3

4- VOLTAGE AND FREQUENCY Pg. 4

5- INSTALLATION Pg. 4

6- MAINS CONNECTION Pg. 5

7- DMX SIGNAL CONNECTION Pg. 6

8- DMX ADDRESSES Pg. 7

9- DISPLAY PANEL Pg. 8

10- DISPLAY FUNCTIONS Pg. 8

11- ERROR MESSAGES Pg. 11

12- HIDDEN MENU Pg. 12

13- OPENING UP THE PROJECTOR HOUSING Pg. 13

14- PERIODIC CLEANING & CONTROLS Pg. 13

15 WIRING CONNECTION Pg. 15

16- DMX SIGNAL FUNCTION Pg. 17

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3.1 Lamp alignment

5.1 Safety chain

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6.1 Protection

8.1 Changing the DMX addresses

10.1 Automatic operation

10.2 Pan & Tilt speed (SPEE) (default: 2)

10.3 Fan speed (FANS) (default: 6)

14.1 Lenses and raylight reflectors

14.4 Fans and air passages

14.3 Lamp

14.4 Mechanical parts

14.5 Electrical components

14.6 Fuse replacement

14.7 Warning!

1- TECHNICAL FEATURES

- New motorized moving head

- ABS cover

- 150mm fresnel lens

- MSD 250/2 lamp

- Control: max 16 channels DMX

- Fast, silent and precise movement

- Position controlled pan (540°) and tilt (270°) by encoder

- Motorized zoom (13°-23°)

- Colour mixing by CMY

- Colour wheel with 6 dichroic high chromatic yield filters +2 filters for

temperature colour conversion 3200°K and 5600°K + Rainbow effect

- Effects wheel with modulation of beam shape 0 180° and Frost effect.

- Mechanical dimmer

- Strobe effect 10 Flash/sec.

- Display for settings and addresses

- Possibility of regulating internal fans and motors to adjust to the

temperature in which the unit is functioning

- Possibility to function autonomously

- Weight: 20Kg

1XR250

WASH

590

360

410

230

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

2.2 Prevention of electric shock:

2.3 Protection against ultraviolet radiation:

2.4 Safety:

2.5 Level of protection against the penetration of solid and liquid matter

1. XR250WASH uses a Philips MSD250/2 lamp . The use of any alternative lamp is not

recommended and will null and void the fixture's warranty.

2. Never locate the fixture on any flammable surface.

3. Minimum distance from flammable materials: 0.5 m.

4. Minimum distance from the closest illuminable surface: 2 m.

5. Replace any blown or damaged fuses only with those of identical value. Refer to the

wiring diagram if there is any doubt.

6. Connect the projector to mains power via a thermal magnetic circuit breaker.

- High voltage is present inside the unit. Isolate the projector from the mains supply

prior to performing any function which involves touching the inside of the unit, including

lamp replacement.

- The level of technology inherent in the XR250WASH requires the assistance of

specialised personnel for all servicing. Refer all work to your authorised DTS service

centre.

- A good earth connection is essential for proper functioning of the projector.

Never connect the unit without proper earth connection.

- The fixture should never be located in a position exposed to rain or in areas of extreme

humidity. A steady supply of circulating air is essential.

1. Never turn the lamp on if any of the lenses, filters or the carbon fibre housing is

damaged. Their respective shielding functions will only operate efficiently if they are in

perfect working order.

2. Never look directly into the lamp when it is on.

- The projector should always be installed with bolts, clamps and other fixtures that are

capable of supporting the weight of the unit.

- Always use a second safety chain of a suitable rating to sustain the weight of the unit

in case of the failure of the main fixing point.

- The external surface of the unit, at various points, may exceed 150°C. Never handle the

unit until at least 10 minutes have elapsed since the lamp was turned off.

- Always replace the lamp if any physical damage is evident.

- Never install the fixture in an enclosed area lacking sufficient air flow. The ambient

temperature should not exceed 35°C.

- A hot lamp may explode, so always wait for at least 10 minutes to elapse after the unit

has been turned off prior to attempting to replace the lamp.

Always wear suitable hand protection when handling the lamp.

- The projector is classified as an ordinary appliance and its level of protection against

the penetration of solid and liquid matter is IP 20. XR250WASH uses MSD250/2 Philips

lamps with GY 9.5 base.

The temperature inside the projector can reach 150° C after just 5 minutes, but it can

2XR250

WASH

get as high as 350° C. Always check that the lamp is cold before attempting to remove it.

In any case, only open the appliance 10 minutes after it has been turned off.

Philips MSD250/2

Power 250W

Luminous flux 18.000 lm

Colour temperature 8500°K

Lampbase GY9.5

Rated life 2.000 hours

1) Using a PHILIPS screwdriver, remove the 3 screws (X,Y, Z) (photo 1, black screws)

which hold the lampholder in place and are located at the rear of the projector head.

2) Remove the lampholder unit. Locate the lampholder (photo 2).

3) Insert the lamp (photo 3)

The lamp used is manufactured from quartz glass and should be handled with care.

Always adhere to the instructions supplied in the lamp's packaging. Never touch the

glass directly but use the tissue provided in the lamp's packaging. The GY 9.5 lampbase

is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, re-read the instructions

and repeat the procedure.

4) Replace the lamp assembly (photo 4) and replace and tighten the screws (X,Y,Z),

which were previously removed (photo 1).

Attention: we recommend that the lamp be realigned in the optical train of the unit to

avoid overheating of the dichroic filters and other components inside the unit. (Photo 5).

Alignment is carried out using the 3 adjusters A, B and C (white screws).

During this operation you must bring the hot-spot to the centre of the beam and flatten

3- MOUNTING THE LAMP

Warning: turn power off before opening the appliance.

3.1 Lamp alignment

Foto 5

Foto 2Foto 1 Foto 3

XR250

WASH

it as much as possible.

The projector can operate at 230V voltage, at 50 or 60 Hz. D.T.S. presets a voltage of

230V at a frequency of 50Hz (barring specific requests).

XR7 may be either floor or ceiling mounted.

For floor mounting installations, the XR7 is supplied with four rubber mounting feet (B)

on the base.

For ceiling mounted installations, we suggest the use of appropriate clamps or fixings to

attach the fixture to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hang it. The structure should also be

sufficiently rigid so as not to move or shake whilst the XR7 moves during its operation.

Four quarter turn fast locks placed on the base of the units allow for the fixing of

brackets that can then be fixed on to the rails with the use of C clamps or Aliscaf type

clamps.

We recommend the use of a safety cable or chain connected to the Xr7 Wash and to the

suspension truss in order to avoid the fixture accidentally falling should the main fixing

point fail. Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain to the two holes (A) located on the base of the fixture,

as shown in the diagram below.

4- VOLTAGE AND FREQUENCY

5- Installation

5.1 Safety chain

4XR250

WASH

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6.1 Protection

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid. The proper working

of the unit would be compromised should this occur.

The projector has a maximum movement of 540° in the base and 270° in the yoke. DO

NOT place any obstructions in the path of the projector's movement.

Each fixture produces heat and must be installed in a well-ventilated position. The

minimum recommended distance from flammable material is 0.5m. Minimum distance

from the object being illuminated is 2 m.

You will note, on inspection, that the fixture features various air inlets and cooling fans

located on both the base and head of the fixture. These should, under no circumstances,

be blocked or obstructed whilst the projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper

operation.

The projector should never be installed in places that lack a constant flow of air. The

ambient temperature should NOT exceed 35°C.

XR250WASH operates at voltage 230V at 50 or 60Hz.

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is of a suitable rating of 8 amps at 230V.

Strict adherence to regulatory norms is strongly recommended.

The use of a thermal magnetic circuit breaker is recommended for each XR250WASH.

A good earth connection is essential for the correct operation of the projector.

6- MAINS CONNECTION

230V a 50 o 60Hz

5XR250

WASH

540° 135°135°

7- DMX SIGNAL CONNECTION

The unit operates using a digital DMX 512 (1990) signal. Connection between the

control box and the projector or between projectors must be carried out using a two pair

screened ø0.5 mm cable and a CANNON .

Ensure that all conductors are isolated from one another and from the metal plug

housing.

The plug housing must be isolated. Connect the control box signal to the DMX IN

projector plug and connect it to the next projector by connecting the DMX OUT plug on

the first projector to the DMX IN plug on the second.In this way, all the projectors are

cascade connected.

NB.

- DMX signal not present

- DMX address not valid

- DMX reception problem

Install when the signal wire has to be put in long distances or where there are electrical

disturbments for example in a disco, concert, theater etc we advice to use a dmx terminal.

the dmx terminal or even more a canon xrl-5 connected with a resistance to 120 ohm

between 2 and 3 the resistance is put in the plug of the dmx of the last device that has been

linked as shown following.

The standard configuration of the XR250WASH is with XLR 5 pole connection.

To convert to an XLR 3 pole configuration proceed as follows:

1) Unscrew the external cover (photo 1).

2) Unscrew the screws that fix the connectors to the panel (photo 2).

3) Rotate the electronic card by 180° (photo 3).

4) Position the 3 pole connectors in the special holes and close.

XLR 5 or 3 pole connector

If the display showing the DMX address flashes, then one of the following errors has

occurred:

TERMINAL DMX SIGNALS:

Foto 2Foto 1 Foto 3

6XR250

WASH

11=GND

2=DATA-

3=DATA+

CONTROLLER

STANDARD

DMX 512

OUT

120 ohm

PIN 3

PIN 2

ATTACHMENT OF THE TERMINA DMX INSTALL A

RESISTANCE OF 120(OHM)BETWEEN 2 AND 3 IN

THE PLUG XRL AND INSERT IN THE DIGITAL PLUG

OUT OF THE LAST DEVICE OF THE ROW

8- DMX Addresses

XR250WASH can be used in three different modes: 8, 10 or 14 DMX channels.

If you want to use a DMX controller with 8 channels, select the 8 CH mode from the

MODE menu and set the following addresses:

Projector 1 A001

Projector 2 A009 If you want to select the next projector, just add “8”

Projector 3 A017

….. A….

projector 6 A041

If you want to use a DMX controller with 10 channels, select the 10 CH mode from the

MODE menu and set the following addresses:

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

Projector 6 A051

If you want to use a DMX controller with 14 channels, select the 14 CH mode from the

MODE menu and set the following addresses:

Projector 1 A001

Projector 2 A015 If you want to select the next projector, just add “14”

Projector 3 A029

….. A….

Projector 6 A071

The address that has to be set on each projector generally depends on the number of

channels that the DMX mixer allots it.

If you have a 12 channel controller, set your XR250WASH to 10 CH MODE. The first

projector will have an A001 address and if you want to select the next projector, then

you have to add 12. The subsequent address will then be A0013

1) Press the UP-DOWN key until you reach the required DMX number. The numbers on

the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing

and the projector is now controlled by the new 512 DMX number.

WARNING: if you press the UP-DOWN keys together the channels are calculated more

quickly and you get a faster selection.

8.1 Changing the DMX address

7XR250

WASH

Table des matières

Autres manuels DTS Matériel de DJ

DTS

DTS 03.MS014.EBLFP Manuel utilisateur

DTS

DTS Portfolio Manuel utilisateur

DTS

DTS XR2000 SPOT CMY Manuel utilisateur

DTS

DTS Alchemy 7 Manuel utilisateur

DTS

DTS MINI BRICK Manuel utilisateur

DTS

DTS SCENA LED 80 CT Manuel utilisateur

DTS

DTS ALCHEMY 5 Manuel utilisateur

DTS

DTS SOPRANO Series Manuel utilisateur

DTS

DTS SCENA LED 200 Series Manuel utilisateur

DTS

DTS Titan HP Manuel utilisateur

DTS

DTS BRICK Manuel utilisateur

DTS

DTS X BRICK Manuel utilisateur

DTS

DTS SCENA LED 120 HQS Manuel utilisateur

DTS

DTS Synergy 5 Spot Manuel utilisateur

DTS

DTS Wonder D Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

DTS

DTS DOCTUS Series Manuel utilisateur

DTS

DTS NICK NRG 501 Manuel utilisateur

DTS

DTS EUPHONY 3 Manuel utilisateur

DTS

DTS XR2000 SPOT CMY Manuel utilisateur

DTS

DTS Synergy 7 Profile Manuel utilisateur

DTS

DTS X-BRICK Manuel utilisateur

DTS

DTS ARTEMIO PROFILE Manuel utilisateur

DTS

DTS Synergy 7 Profile Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur