DSE RKK Series Manuel utilisateur
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:2
What did you buy
The RKK series WiFi kits allow a maximum distance between cameras and NVRs of about 3-4 rooms. If you
place the RKK-KIT1 repeater in the coverage area of the kit, you will re-launch the signal for a further 3-4
rooms. You can use maximum 2 repeaters in one kit.
If you purchase the repeater together with the wifi kit, it will be delivered to you already configured with the kit
This manual explains how to install the repeater you buy later, by connecting it to one of our wifi kits
that already works.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:3
Make the network of the NVR visible
The first thing you need to do to install a wifi repeater in your kit is to make the NVR's wifi network visible
from external devices, such as a mobile phone. You can do this in the NVR settings in the NETWORK/WIFI
section and by pressing the ADVANCED button
The important entry is AREA. Select AREA: EU and check that SPREAD SSID is ticked. At the end press
CONFIRM and then APPLY. When finished, restart the NVR.
Don't worry for your kit, this modification doesn't change anything in the communication between NVR
and cameras, but it simply makes the wifi network of the NVR visible, which will come in handy when
installing the repeater.
If you now explore the available wifi networks, with a mobile phone or tablet, you will find the NVR network among
the wifi networks. The network name is called the SSID.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:4
In the wifi settings of the NVR you will also find the
Password to access the wifi network which by default is "lspassword” (the
first letter is a lowercase L)
You now have full control over your NVR's wifi network: you can see the NVR's wifi network with other
devices, know its name (SSID) and access password.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:5
Choose the location of the
repeater
To install an RKK-EXT1 repeater you just need to plug it into the power outlet. However, the location you
choose is crucial for proper functioning.
1 – ONLY ONE RKK REPEATER
The repeater must be installed at a certain distance from the NVR, but without leaving its wifi coverage.
You can check the signal strength with a mobile phone. Once installed, the repeater also has a lighting
around the front button: the red light indicates that the main network signal is insufficient, the blue light
indicates that reception is correct. Here is an example of a repeater installation. Note that the left camera
communicates with the NVR, while the right camera connects to the repeater
2 – TWO RKK REPEATERS
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:6
To cover even large areas you can install up to 2 repeaters in your system. If you do this, remember that
the two repeaters must be placed in opposite directions with respect to the NVR and never in the same
direction. If you install the two repeaters on the same side in the NVR you risk that they connect to each
other and your system would not work. It is not recommended to install more than two repeaters in a
system.
See below an example of an installation with two repeaters.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:7
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:8
Ignition sequence with repeater
If you use a repeater you must avoid that distant cameras, which must connect to the repeater, connect by
mistake to the NVR, which has the same SSID. This could happen if the NVR network reaches, even if only
weakly, the distant cameras.
To avoid this, you can respect this ignition sequence when you start up the system
1 - Turning on the repeater
2 – Switching on the remote cameras that need to connect to the repeater
3 - Turning on the NVR
4 – Turn on the nearby cameras that connect to the NVR
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:9
Connect the repeater purchased
together with the RKK wifi kit
If you bought the wifi repeater together with your wifi kit, you don't have to worry about any configuration,
because it is delivered to you already paired with your NVR, ready to work. The cameras will automatically
connect to the repeater if the NVR network is not available because it is too far away.
Insert the repeater halfway between the NVR and a camera too far away to allow reception. The repeater
allows you to relaunch the wifi signal of the NVR to reach the farthest cameras.
If you bought the repeater with the kit, you can avoid studying the following chapters, which talk about
setting up a repeater purchased separately.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RKK SERIES – RKK-EXT3 WIFI REPEATER
Page:10
Set up a repeater not purchased
with the kit.
If you didn't buy a repeater with the kit, don't worry. It is quite common to buy it later to solve problems
of range due to unforeseen obstacles. In this case, before you can use the repeater, you must connect it
to the wifi network of your NVR, following the instructions below.
Plug the repeater into a socket near the NVR. The front light comes on.
1 – SEARCH FOR THE REPEATER'S NETWORK
Search for wifi networks with your mobile phone and you will find the wifi network generated by the 2.4GHZ repeater
as in this example with the name COM----
2 – CONNECT TO THE REPEATER'S NETWORK
Connect to the repeater's network. By default, no password is required.
If your mobile warns you that this network does not have Internet, choose to continue and
DSE SRL – ITALY – WWW.DSE.EU
Autres manuels pour RKK Series
4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels DSE Répétiteur
