DSC PC2550 Manuel utilisateur

Code Changes

User’s Programming Commands

[*]+[5]+[MASTER CODE]

The [*][5] user’s programming commands are used to program additional access codes. Up to 16 user arm-

disarm codes may be programmed. The 1st code is the Master Code (factory default [1234]). The 16th code

is optionally a “One Time Use”or maid code. The 16th code may be changed from a “One Time Use” code to

a regular code using an installer’s programming command (section [15]...light 8). Remember if no keypad

entry is made for more than 2 minutes the keypad will return to the normal arm-disarm display and the

complete command will have to be re-entered to program a new access code.

Programming Additional Access Codes

1. Press the [*] and [5] keys then enter the Master Security Code (default [1234]) to enter the additional code

programming mode. The “Program” light and “Zone 1” light will be on to show that the rst code (the Master

Code) is already programmed with the factory default code [1234]. The Master Code may be changed but do

not try to erase the Master Code. The installer can disable user changing of the Master Code by turning on

light 2 in section [16].

2. 15 additional codes may be programmed. The zone lights are used to indicate which of these codes are

already programmed (zone light on steady) and the one which is currently being programmed (zone light is

ashing).

3. To program the second code, press [2] and zone 2 light will ash. Then enter a 4 digit code and the buzzer

will beep three times and zone light 2 will come on steady indicating a programmed code.

4. To remove the second code, press [2] - the buzzer will beep three times and zone light 2 will ash. Enter

[*] [*] [*] [*], the buzzer will beep three times and zone 2 light will go out to show that the code has been

removed.

5. Follow the instructions in 3 or 4 for programming or removing any of the other additional codes.

6. To program access codes 9 to 16, press 9 to toggle into the upper code region. Zone lights 1 to 8 now rep-

resent access codes 9 to 16 (light 1 is code 9.... light 8 is code 16). The “Ready” and “Armed” LEDs will ash to

indicate that the user is in the upper programming region. Program or remove access codes 9 to 16 as stated

in 3 and 4 above. Press 9 again to toggle back down to the lower region (access codes 1 to 8).

7. Do not try to remove the Master Code (1st code). The Master Code may be changed but it must not be

removed. When changing the Master Code be sure to enter a valid 4 digit number (use only number keys 0

to 9). Do not enter [#] or [*] as one of the digits. If the Master Code is forgotten and the panel is left disarmed,

program a new Master Code using the [*][8][Installer’s Code][25] command. If the Master Code is forgotten

and the panel is left armed, use the 2nd Master Code to disarm the system. If the 2nd Master Code is not

programmed then the entire programming can be reset to factory default by using the “Hardware Reset”

method described on page 24.

8. To successfully program or remove additional codes, the panel must be put into the code program mode

by following step 1 followed by steps 3 or 4. Note that if no key entry is made for 2 minutes the panel will go

back to the normal arm/disarm mode, after which step 1 must be repeated to get back into the code pro-

gram mode.

9. To exit the code program mode press [#].

To review:

programming a new code;

enter [*] [5] [Master Code] [1 to 8] [4 digit code], or

[*] [5] [Master Code] [9] [1 to 8] [4 digit code]

eliminating an existing code;

enter [*] [5] [Master Code] [2 to 8] [* * * *], or

[*] [5] [Master Code] [9] [1 to 8] [* * * *].

Note: The access code numbers must be entered as

one digit. E.g. 2, 3,......, 7, 8.

Autres manuels pour PC2550

Table des matières

Autres manuels DSC Système de sécurité

DSC

DSC Power832 P5010 Manuel utilisateur

DSC

DSC 3G2055 Manuel utilisateur

DSC

DSC iotega WS900UL Manuel utilisateur

DSC

DSC Power832 PC5010 Manuel utilisateur

DSC

DSC neo HS2032 Manuel utilisateur

DSC

DSC Power832 Manuel utilisateur

DSC

DSC WS4965 Manuel utilisateur

DSC

DSC TL260 Manuel utilisateur

DSC

DSC Power8 PC5005 Manuel utilisateur

DSC

DSC 3G2055 Manuel utilisateur

DSC

DSC PC1550 Manuel utilisateur

DSC

DSC PowerSeries SCW9047-433 Manuel utilisateur

DSC

DSC New Classic PC585 Manuel utilisateur

DSC

DSC PC1555 - 2 Manuel utilisateur

DSC

DSC PTD1610-SCW Manuel d'exploitation et d'entretien

DSC

DSC PC5008 Manuel utilisateur

DSC

DSC Power832 PC5015 Manuel utilisateur

DSC

DSC Digital Security Control PC158O Manuel utilisateur

DSC

DSC PC2550 Manuel utilisateur

DSC

DSC PC550 Manuel utilisateur

DSC

DSC MAXSYS PC4020 Manuel utilisateur

DSC

DSC PC5020 Power864 Manuel utilisateur

DSC

DSC PG4975 Manuel

DSC

DSC PC 5010 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur