Enter New Password Screen
This screen appears after the user confirms they want to change the
password. User should press the "CLR" button, enter new four-digit
password then press the “ENT” button. As new digits are entered
they will appear in the top right of the screen directly beside the
phrase ‘Enter New Password”
If user mistakenly presses an incorrect numeral they can press the
“CLR” button and start over.
Password Changed Screen
This screen appears after the users enters the new password. The
new password will be displayed in the center of the screen.
Press “Continue” to return to the Operation Selection Screen.
Manually Operating Devices from Relay Panels
In the event of a control processor or interface failure, the Smart Gym allows for
emergency manual operation of devices for the relay panel.
Limited Warranty - Draper Smart Gym Group Control System
All Smart Gym Group Control System and related
components are warranted to the end user for
a period of One (1) year from date of substantial
completion shipment or 18 months after shipment,
whichever occurs first. In the event that any
component fails under normal use and conditions,
that component will be replaced or repaired. Routine
maintenance and adjustment excluded.
Misuse or abuse from vandalism, improper
installation or improper maintenance is not covered
under this warranty. Under no circumstances will
cracked or broken touch screen glass be covered
under this warranty Damages due to extreme
weather conditions such as floods, tornadoes or
other Acts of God are also expressly not covered
under this warranty.
THIS WARRANTY DOES NOT COVER:
1.
Dissatisfaction due to improper installation or
maintenance or dissatisfaction due to deviation
from printed installation and maintenance
instructions.
2.
Damage in use due to tears, punctures, burns,
scuffs, accidents emanating from lack of, or
improper operation in conjunction with adjacent
equipment or any intentional misuse of the
product or vandalism.
3.
Liability for consequential, incidental, special or
any other damages, no matter what the cause.
DATE OF EXPIRATION:
One (1) year from date of substantial completion and
acceptance by the owner or eighteen (18) months
after date of shipment, whichever comes first.
Maintenance Schedule
Your Smart Gym Control System has
been custom programmed to match your
specific needs, and designed to provide
many years of trouble free service.
There are no owner serviceable or
programmable components to the Smart
Gym Control System. If your system
malfunctions, you should contact Draper
or your local Draper representative for
assistance.
Touch Screens have glass faces and
can break if not used properly. If
Glass breaks, discontinue use and
contact Draper or your local Draper
representative
for assistance. Touch Screens can be
cleaned with slightly damp cloth or lens
wipe like used to clean glasses or mobile
phones.
1.
Locate relay panel worksheet that tells you which devices are connected to each
relay. The appropriate worksheet should have left during initial installation in or
around each relay panel. If you are unable to locate the necessary worksheets,
contact Draper or your local Draper representative for assistance.
2.
Remove the cover of the relay panel. Use extreme caution to avoid contact with any
of the wires connected to any of the relays to avoid injury from shock.
3.
Locate the local control section on the right-hand side the GLXX-CTRL module that
is at the bottom middle of the relay panel.
4.
Depress the button marked ENABLED. Red LED next to button will illuminate
5.
Use the buttons marked with up and down arrows to navigate to the relay number
that you want to operate. The relay number will be displayed by the
NET ID LED display.
6.
Make sure the area around the device to be operated is clear and that someone who
has clear view of device to be operated, has a clear chain of communication to the
person at the relay panel.
7.
Press the ON button and device will start to operate.
8.
Once device is in desired position press the off button.
9)
Continue to operate equipment until all items are in desired position then depress
the Enable button making sure adjacent LED is no longer illuminate red.
•
This should only be
used in the event of
such failures and
only when absolutely
necessary.
•
Ensure area around
device to be operated
is clear of people and
equipment.
•
If the equipment being
operated is not visible
from the relay box
location two or more
people need to form a
communication “chain”
between the point where
the device is visible and
the relay panel.
•
In Manual mode relays
act in a maintained
manner or like a simple
on-off switch. Only
one device should be
operated at a time and
once the device is in
desired position, relay
should be moved to off
condition.
RELAY
LOCAL CONTROL
ON
OFF
Toggles Local Control
On/Off
Toggles Selected Relay
On/Off
Use Up/Down Arrows
to Select Relay to Control
(NET ID will display relay number)
Red LED Illuminates
when local control
is enabled
ENABLE
page 4 of 4
Smart Gym with
503338 4.3" Text Touch Screen
