Draper VMS/KD Manuel utilisateur

■STOCK No. 64600 ■PART No.VMS/KD

•INSTRUCTIONS•

03/2001

IMPORTANT: PLEASE READ THESE INSTRUCTIONS

THOROUGHLY BEFORE USE.

UNDERSTANDING HOW THIS MACHINE WORKS AND SETTING IT

CORRECTLY IS FUNDAMENTAL TO OBTAINING

A SATISFACTORY RESULT.

MITRE SAW

MITRE SAW TECHNICAL DATA

COMPONENT PARTS

1. Vice clamp assembly.

2. Length stop assembly.

3. Cut depth stop.

4. Cut depth stop screws.

5. Two plastic feet with screw holes

for bench mounting.

6. Base socket head screws.

7. Pre-set angle arm.

8. Pivot pin.

9. Plated cursor screw.

10. Cursor.

11. Blade tensioning nut.

12. Pivot screw.

13. Saw table.

14. Saw frame handle.

15. Saw frame guide bar carriers.

16. Saw blade.

17. Saw frame carriers.

18. Saw frame assembly.

Specification:

Max. cutting width clamped at 45°............110mm

Max. cutting width clamped at 90°............160mm

Max. cutting height ...................................120mm

Blade length..............................................550mm

Blade width.................................................45mm

Table length ..............................................400mm

Max. reach of adjustable stop...............

450mm

Weight......................................................3.1kg

PRE-SET ANGLES

ASSEMBLY OF ACCESSORIES

The vice clamp ✕✌ can be mounted on the left or right hand side of the saw table front

for holding workpieces securely.

The adjustable length stop ✖✌ can be mounted at either end of the saw table and set

for the required length of cut.

90˚

45˚ 36˚

30˚ 22.5˚

✕✌

✖✌

IMPORTANT WARNING

To get the best from your saw and ensure it is correctly set ensure the following is

correct:

(a) The saw blade is tensioned sufficiently to avoid ‘whip’ which will cause the blade to

deviate from a true cut.

(b) The blade is ‘in line’ and central to the frame.

(d) Tension is always released after use.

(e) The correct type of blade for the application is used.

(f) After assembly and setting has been carefully carried out, always test your mitre

saw and the angles with some scrap timber to ensure the machine is assembled

correclty and cutting true.

SPARE BLADES

Spare blades are available for this Mitre Saw. Draper Stock No. 60506 ..............14tpi

60507 ..............18tpi

60508 ..............24tpi

DRAPER TOOLS LIMITED,

Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K.

Helpline: (023) 8049 4344.

Sales Desk: (023) 8049 4333.

General Enquiries: (023) 8026 6355.

Fax: (023) 8026 0784.

http://www.draper.co.uk

e-mail: [email protected]

©Published by Draper Tools Ltd.

No part of this publication may be reproduced,

stored in a retrieval system or transmitted in

any form or by any means, electronic, mechanical

photocopying, recording or otherwise without prior

permission in writing from Draper Tools Ltd.

Table des matières

Autres manuels Draper Scie

Draper

Draper 56791 Manuel utilisateur

Draper

Draper MS560/3 Manuel utilisateur

Draper

Draper CTS315 Manuel utilisateur

Draper

Draper BS250B Manuel utilisateur

Draper

Draper 254mm Table Saw Manuel utilisateur

Draper

Draper RS12VD Manuel utilisateur

Draper

Draper 98446 Manuel utilisateur

Draper

Draper SMS250AB Manuel utilisateur

Draper

Draper BTS205 Manuel utilisateur

Draper

Draper CS14B Manuel utilisateur

Draper

Draper MS210C Mise à jour du firmware

Draper

Draper ABSSG Mise à jour du firmware

Draper

Draper CS153 Manuel utilisateur

Draper

Draper RSAW900D Manuel utilisateur

Draper

Draper FS405V Manuel utilisateur

Draper

Draper STORMFORCE BS200/250SF Manuel utilisateur

Draper

Draper MS210 Manuel utilisateur

Draper

Draper CTS315A Manuel utilisateur

Draper

Draper 1600W 185mm Circular Saw Manuel utilisateur

Draper

Draper 88192 Manuel utilisateur

Draper

Draper SMS210 Manuel utilisateur

Draper

Draper PT187A Manuel utilisateur

Draper

Draper PT185A Manuel utilisateur

Draper

Draper CS14A Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur