Draper 37777 Manuel utilisateur

HYDRAULIC

MOTORCYCLE

& ATV LIFT

37777

These instructions accompanying the product are the original instructions. This document is part of the product, keep

it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before

assembling, operating or maintaining this product.

This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,

and contains all the necessary information to ensure its correct and safe use. By following all the general safety

instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the

product itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the

product.

Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools

policy of continuous improvement determines the right to make modiﬁcations without prior warning.



1.1 INTRODUCTION:

USER MANUAL FOR: Hydraulic Motorcycle & ATV Lift

Stock No: 37777

Part No: MC/ATV2B

1.2 REVISIONS:

Date ﬁrst published September 2021.

As our user manuals are continually updated, users should make

sure that they use the very latest version.

Downloads are available from: http://drapertools.com/manuals

Draper Tools Limited Draper Tools Limited

Hursley Road Oude Graaf 8

Chandler’s Ford 6002 NL

Eastleigh WEERT

Hampshire Netherlands

SO53 1YF

Website: drapertools.com

Product Help Line: +44 (0) 23 8049 4344

General Fax: +44 (0) 23 8026 0784

1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:

Warning! – Information that draws attention to the risk of injury or death.

Important – Information that draws attention to the risk of damage to the product or surroundings.

Permission is granted to reproduce this publication for personal and educational use only.

Commercial copying, redistribution, hiring or lending is prohibited.

No part of this publication may be stored in a retrieval system or transmitted in any other form or

means without written permission from Draper Tools Limited.

In all cases this copyright notice must remain intact.

1. TITLE PAGE

– 2 –

2. CONTENTS

– 3 –

2.1 TABLE OF CONTENTS

1. TITLE PAGE

1.1 INTRODUCTION.......................................................................................................... 2

1.2 REVISIONS.................................................................................................................. 2

1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT ......................................... 2

2. CONTENTS

2.1 TABLE OF CONTENTS ............................................................................................... 3

3. WARRANTY

3.1 WARRANTY................................................................................................................. 4

4. INTRODUCTION

4.1 SCOPE......................................................................................................................... 5

4.2 SPECIFICATION.......................................................................................................... 5

4.3 HANDLING AND STORAGE........................................................................................ 5

5. HEALTH AND SAFETY INFORMATION

5.1 GENERAL SAFETY INSTRUCTIONS ......................................................................... 6

5.2 RESIDUAL RISK.......................................................................................................... 6

6. TECHNICAL DESCRIPTION

6.1 IDENTIFICATION......................................................................................................... 7

7. UNPACKING AND CHECKING

7.1 PACKAGING ................................................................................................................ 8

8. ASSEMBLY & PREPARATION

8.1 FITTING THE HYDRAULIC UNIT & FOOT PEDAL..................................................... 9

8.2 BLEEDING THE HYDRAULIC SYSTEM ..................................................................... 9

9. OPERATION & USE

9.1 GENERAL OPERATIONAL PROCEDURE................................................................ 10

10. MAINTENANCE

10.1 MAINTENANCE......................................................................................................... 11

11. DISPOSAL

11.1 DISPOSAL ................................................................................................................. 12

12. EXPLANATION OF SYMBOLS

12.1 EXPLANATION OF SYMBOLS.................................................................................. 13

3. WARRANTY

– 4 –

3.1 WARRANTY

Draper tools have been carefully tested and inspected before shipment and are guaranteed to be

free from defective materials and workmanship.

Should the tool develop a fault, please return the complete tool to your nearest distributor or

contact:

Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.

Telephone Sales Desk: +44 (0) 8049 4333 or Product Help Line +44 (0) 23 8049 4344.

A proof of purchase must be provided with the tool.

If upon inspection it is found that the fault occurring is due to defective materials or workmanship,

repairs will be carried out free of charge. This warranty period covering parts/labour is 12 months

from the date of purchase except where tools are hired out when the warranty period is 90 days

from the date of purchase. This warranty does not apply to any consumable parts, any type of

battery or normal wear and tear, nor does it cover any damage caused by misuse, careless or

unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other than

the authorised Draper warranty repair agent.

Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will

be quoted and made accordingly.

This warranty applies in lieu of any other warranty expressed or implied and variations of its terms

are not authorised.

Your Draper warranty is not effective unless you can produce upon request a dated receipt or

invoice to verify your proof of purchase within the warranty period.

Please note that this warranty is an additional beneﬁt and does not affect your statutory rights.

Draper Tools Limited.

4. INTRODUCTION

4.1 SCOPE

Foot operated lever style hydraulic lifting mechanism. Rubber support arms to help prevent

damage, suitable for lifting bikes, quads and all terrain vehicles.

This product is suitable for enthusiasts and tradespersons alike. Any application other than that it

was intended for is considered misuse.

4.2 SPECIFICATION

Stock No. ................................................................................................................................. 37777

Part No. ........................................................................................................................... MC/ATV2B

Safe working load..................................................................................................................... 680kg

Minimum height ...................................................................................................................... 120mm

Maximum height ..................................................................................................................... 380mm

Platform size................................................................................................................. 335 × 330mm

Base size...................................................................................................................... 810 × 370mm

Lift Height ............................................................................................................................... 260mm

Platform mat thickness ............................................................................................................... 3mm

Platform mat size............................................................................................................ 55 × 335mm

Platform frame thickness............................................................................................................ 3mm

Lifting arms thickness.............................................................................................................. 2.5mm

Base frame thickness .............................................................................................................. 3.8mm

4.3 HANDLING AND STORAGE

− Care must be taken when handling this product.

• This product is not a toy and must be respected.

− Environmental conditions can have a detrimental effect on this product if neglected.

• Exposure to damp air can gradually corrode components.

• If not cleaned and maintained correctly or regularly, the machine will not perform at its best.

– 5 –

5. HEALTH AND SAFETY INFORMATION

5.1 GENERAL SAFETY INSTRUCTIONS

Warning! Before use, ensure that the motorcycle to be supported has a suitable structure and

centre of gravity to accommodate the platform without damaging the motorcycle. DO NOT use if

the stand will foul on the exhaust or other vulnerable parts.

− Locate the stand in a suitable work area. Keep area clean and tidy and free from unrelated

materials and ensure that there is adequate lighting. Also ensure that the ﬂoor is level and

strong enough (preferably concrete) to take the weight of the stand and the bike. DO NOT

operate the stand on tarmacadam, as the surface may be unstable.

− Keep the stand clean for best and safest performance.

− The maximum bike weight is 680kg. DO NOT exceed this rated capacity.

− Before lifting check that there are no overhead obstructions.

− Keep children and unauthorised persons away from the work area.

− DO NOT use the stand for a task it is not designed to perform.

− DO NOT operate the stand if damaged.

− DO NOT exceed the rated capacity of the stand.

− DO NOT allow untrained persons to operate the stand.

− DO NOT make any modiﬁcations to the stand.

− Before lowering the stand ensure that there are no obstructions underneath the motorcycle and

that all persons are standing clear.

− Before storing, ensure that all parts are clean and free of grease and oil and the stand is fully

lowered. Store stand in a safe area.

Warning! The instructions referred to in this manual are unable to cover all possible situations that

may occur. It must be understood that common sense and caution are factors which are unable to

build into this product, but must be applied by the operator.

5.2 RESIDUAL RISK

Important: Although the safety instructions and operating manuals for our tools contain extensive

instructions of safe working with lifting equipment, every machine involves a certain residual risk

which can not be completely excluded by safety mechanisms. Lifting equipment must therefore

always be operated with caution!

– 6 –

6. TECHNICAL DESCRIPTION

– 7 –

6.1 IDENTIFICATION

(1) Lift foot pedal.

(2) Handle.

(3) Castor wheels.

(4) Safety bar.

(5) Fixed wheels.

(6) Hydraulic ram unit.

(7) Lift base.

(8) Lower foot pedal.

(9) Rear support feet.

(10) Safety lock mechanism.

(2)

(6)

(1)

(9)

(10)

(5)

(7)(4)

(3)

(8)

7.1 PACKAGING

Carefully remove the product from the packaging and examine it for any sign of damage that may

have happened during shipping. Lay the contents out and check them against the parts shown

below. If any part is damaged or missing, please contact the Draper Help Line (the telephone

number appears on the Title page) and do not attempt to use the product.

The packaging material should be retained at least during the warranty period, in case the

machine needs to be returned for repair.

Warning!

− Some of the packaging materials used may be harmful to children. Do not leave any of these

materials in the reach of children.

− If any of the packaging is to be thrown away, make sure they are disposed of correctly,

according to local regulations.

7. UNPACKING AND CHECKING

– 8 –

– 9 –

8. ASSEMBLY & PREPARATION

8.1 FITTING THE HYDRAULIC UNIT &

FOOT PEDAL – FIGS.1 – 3

− Attach the hydraulic ram unit (6) to the lift base

using the ﬁxings provided. Noting that the unit

will only attach in one orientation (FIG.4).

− Attach the handle (2)to the lift frame using

ﬁxing supplied.

− Locate the lift foot pedal (1) into the socket of

the hydraulic ram unit (6.1)and secure using

screw and washer (1.1).

− Tighten the ram bolt, attach the remaining end

of the foot pedal.

− Extend the hydraulic ram unit, using the foot

pedal (1)and lift the frame to allow the main

pivot bolt (6.2) to be attached to the frame.

− Attach the rear castor wheels (3)to the frame.

− Check tightness of all ﬁxings.

8.2 BLEEDING THE HYDRAULIC

SYSTEM – FIG.4

Before use the hydraulic system must be bled to

ensure safe operation.

− To bleed the system:

• Pump the lift foot pedal (1) until the unit is at

its maximum height.

• While depressing the lower foot pedal (8),

fully pump and release the lift foot pedal at

least 10 full strokes.

• This will purge the valve system of any air.

FIG.

(1.1)

(1)

(8)

(6.2)

(6)(6.1)

(1)

(2)

5FIG.

9. OPERATION & USE

– 10 –

9.1 GENERAL OPERATIONAL

PROCEDURE – FIG.5

Warning! Before use, ensure you read,

understand and apply the safety instructions

before use.

Before use, ensure that the motorcycle has a

suitable structure and centre of gravity to

accommodate the stand without damaging the bike.

− DO NOT use the stand if it will foul on the

exhaust, fairing or other vulnerable parts. If

necessary remove any lower fairing and

ensure that the bike is stable on the stand

before operating.

− Before lifting, ensure that there is nothing above

the motorcycle that could be damaged by using

the lift.

− Position the bike in a suitable area, checking that

the surface on which the stand will be placed is

solid and ﬂat (preferably concrete).

− Ensure there is good access and clearance

beneath the bike for the stand.

− Inspect the underside of the motorcycle for

suitable support points, bearing in mind the

centre of gravity of the motorcycle and which

wheel is to be lifted from the ground.

− Place the stand under the motorcycle in the

approximate position required.

− Pump the lift foot pedal to raise the stand until the platform is just in contact with the underside

of the motorcycle. Adjust the position of the stand as necessary and before lifting begins, use

rear support feet to level stand and ensure load is taken away from rear castor wheels, and

that the stand is fully immobilised. Only when stand is unable to move on the wheels can lifting

begin.

− Pump lift foot pedal to lift motorcycle to required height, ensuring that safety lock mechanism is

operating.

− While working on motorcycle ensure that it will remain stable and that the centre of gravity will

not be affected by removing major/heavy components (wheels, engines etc.).

− Warning! DO NOT move the lift while loaded as serious damage, personal injury or

death may be caused.This unit IS NOT designed to transport or move items – It is a lift

ONLY.

− When work is complete, check under the stand to ensure that there are no obstructions and

that it is safe to lower the unit, depress lower foot pedal gently to lower the stand.

− When the stand is fully lowered, ensure that the bike is standing on its wheels and is

supported in the upright position – BEFORE removing the lift.

Table des matières

Autres manuels Draper Système de levage

Draper

Draper AeroLift 35 Manuel

Draper

Draper AeroLift 100 220V Instructions d'installation

Draper

Draper SLX17 Mode d'emploi

Draper

Draper AeroLift 50 Manuel

Draper

Draper AeroLift 25 Manuel

Draper

Draper AeroLift 50 Manuel

Draper

Draper 56177 Manuel utilisateur

Draper

Draper Flatscreen Lift FSL-F-42 Manuel

Draper

Draper AeroLift 25 Manuel

Draper

Draper 78610 Manuel utilisateur

Draper

Draper AeroLift 150 Manuel

Draper

Draper Micro projector lift Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur