DR. Heater DR-233 Manuel utilisateur

Carbon Infrared Heater Indoor/Outdoor

Owner’s Manual

Model No.: DR-233

Warning

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE,

We cannot be liable for any damages caused by failure to observe these instructions.

IMPORTANT SAFETY INSTRUCTIONS

READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation,

maintenance and operation of the heater can be dangerous. Observing the following procedures

will reduce the risk of fire, electric shock, injury to persons and keep installation time to a minimum.

Save these instructions for future used.

1. Read all instruction before using this heater.

2. Remove the unit from its packaging and check to make sure it is in good condition before using.

3. Do not let children play with parts of package (such as plastic bags).

4. Check the household voltage to ensure it matches the heater’s rated specification.

5. Check the power cord and plug carefully before used, to make sure that they are not damaged.

6. Before unplugging the power cord, be sure to turn off the power, when energizing the unit, be

sure your hands are dry to prevent from electric shock.

7. Do not use flammable objects near or point the heater like furniture, pillows. bedding, paper,

clothes and curtains at least 3 feet (1meter) from the front of the heater and keep them always the

sides and rear.

8. Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.

9. To protect against electric shock, do not immerse cord or plug in water or any other liquid.

10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may

cause an electric shock, fire or damage to the heater.

11. Always unplug the heater when not in use.

12. Do not allow cord to overhang the counter top where it can be easily pulled by children.

13. Do not put fingers or foreign objects into the grill while in operation.

14. Do not leave the appliance unattended when in use.

15. This heater is not intended for use in bathrooms, laundry and similar indoor locations, never

located heater where it may fall into a bathtub or other water container.

16. No liability can be accepted for any damage caused by non compliance with these instructions

or any other improper use or mishandling.

17. This appliance is not intended for use by persons (including children) with reduces physical,

sensory or mental capabilities or lack of experience and knowledge unless they have been given

supervision or instruction concerning the use of the appliance by a person responsible for their

safety. Children and vulnerable people should be supervised to ensure they do not play with the

appliance.

18. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service

agent or a similarly qualified person in order to avoid a hazard.

19. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of

anything that may cause blockage. Check all inlets and outlets from time to time to ensure it is clear

of any dirt or dust accumulation. DO NOT COVER.

20. Parts of the heater may exceed 200℃, contact with the heating tube, reflector, or metal parts

near the heating tube, may cause severe BURNS . To avoid burns, do not let bare skin touch hot

surface.

21. NEVER place hands under the heating elements. ALWAYS allow heating element to cool at least

10 minutes before touching the heating tube or adjacent parts.

22. This product contains recyclable materials. Do not dispose this product as unsorted municipal

waste. Please contact your local municipality for the nearest collection point.

Introduction

The infrared heaters produce instant and comfortable heat like the sun.

These robust and weatherproof heaters are designed for domestic and commercial heating

applications within indoor and outdoor areas.

Model

DR-233

Voltage(V)

110-120V AC

Wattage(W)

1500

Hertz(Hz)

Dimensions W×H×D(mm)

780×126×136

Weight N.W(KG)

4.0

This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 68.1. An adapter as

shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles.

The green grounding lug extending from the adapter must be connected to a permanent ground

such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded

receptacle is available.

INSTALLATION

Tools Needed:

* Pencil *Hammer *Level *Screw Driver *Power Drill and drill bits

A mounting bracket is provide with the heater which has been specifically designed to allow this

product to be fitted to ceiling or wall before drilling the holders for the ceiling/wall is solid and that

there are no hidden water pipes or electric wires.

ATTENTION! The appliance must be installed on the solid surfaces like concrete, wood or metal etc.

Important: Ensure that the supply cables is well mounted and that it does not come into contact

with reflector of the heater or that does not trail into heated area, the supply cable can be fixed to

the metal mounting bracket behind heater with plastic zip ties.

1. This heater should be installed by a competent person, i.e. a qualified electrician.

2. Always disconnected the heater from the electricity supply and allow it to cool before

installation.

3. This heater can be mounted in a horizontal or vertical manner, but for a higher efficiency we

recommend horizontal usage.

4. For both wall and ceiling mounting, the lowest part of the heater must be located at or above a

minimum height of 2.4m/94.5”from ground level, so that the heater can not be touched when

in operation.

5. For wall mounting, there must be a 2.4m/94.5”distance from your appliance to the ground. For

ceiling mounting, there must be a 2.4m/94.5”distance from your appliance to the ground.

6. For both horizontal and vertical mounting on the wall, there must be a min. distance of

0.4m/15.8”between the appliance and the ceiling.

7. The distance from your appliance from the corners should be min. 0.4m/15.8”for vertical use

and min. 0.5m/19.7”for horizontal use.

8. When installed to the ceiling, there must be a distance of 0.5m/19.7”between corners and the

appliance.

9. The distance of your appliance from the living beings is to be min 1m/39.4”.

10. The distance from the front side of the heater to materials such as wood, carton, cloth etc.,

must be min 1m/39.4”.

11. When mounting horizontally or to a ceiling, do not position the heater at an angle more than

90°and less than 45°.

12. The supply cable must be at the lower end of the heater if the heater is installed at an angle or

vertically.

13. Keep the supply cord away from the body of the heater which will get hot during use.

14. Do not install the heater on an inflammable surface.

15. Observe the minimum safe distance between the heater body and the inflammable surfaces

when mounted.

16. The heater should always have a minimum clearance of 0.5m/19.7”from a ceiling and adjacent

wall.

17. If the heater is to be used outside, a weatherproof outlet is recommended.

18. Before drilling ensure that there are no wires or water pipes in the area where the heater is to

be installed.

19. The heater must be installed on the mounting brackets provided.

20. Fasten the brackets securely to the mounting surface and the backside of the heater using the

nuts and screws supplied.

21. Fasten the heater securely on the brackets using the nuts and bolts supplied.

22. The brackets can be used to adjust the direction of the heater, adjust the heater angle by

loosening the two bolts on the wall mounting bracket, tighten the bolts again when the desired

angle is reached.

Installation

Mounting step

1. L shaped Bracket installation

Fasten the L shaped braket using the screws and nuts provided (no.5 and no.6)

2. Mark holes on the place where the heater to be mounted with a pencil

1.1 "

11.8"-15.7”

3. Drill holes with a smaller diameter drill bit than the plastic anchors

4. Insert the point end of plastic anchor into the holes, Tap the anchor with a hammer until the

anchor is flush

5. Using a screwdriver attach the mounting bracket to the holes which with plastic anchor inside.

6. Fasten the heater on the L shaped bracket with screws on the back of heater

The heater must be installed at least 2.4m above the floor

Attention: cable should not passing thought the heater

Remote Control Instructions

1. POWER BUTTON: Turn the heater off.

2. UP BUTTON: Increase timer and level.

3. DOWN BUTTON: Decrease timer and level.

4. LEVEL BUTTON: Use to adjust the heat levels(L1-L2). Press the Level button then use the up and

down buttons (buttons 2 and 3) to increase or decrease the heating level.

5. TIMER BUTTON: To set the timer from 0H-9H, which is the number of hours it will run. 0H will

display and then adjust to the number of hours you would like to set, using the up and down

buttons (2 and 3).

Noted: All heaters and their remote controls have the same frequency, so it is possible to control

several heaters with just one remote.

PUSH BUTTON: on the right end of heater, it could be manual operated without remote control.

Inserting Batteries

Insert 2 AAA/ Alkaline type batteries into your remote control

1. Flip the backside of your remote control and pull out battery cover. Insert the batteries in

accordance with the instructions and polarity the batteries.

2. Change the batteries in the same way depicted above.

NOTICE:

1. Replace the old batteries with the same type batteries. Otherwise, your heater may not

function well.

2. Pull out the batteries in case of long terms of disuse to prevent leakage which may impair your

remote control.

3. Do not allow water or liquid to get into the remote control.

Caution:

When the appliance is not operated for a long period of time, cleaning or maintenance is conducted

or when the location of the heater is changed, the heater should be turned to OFF and unplugged

from the electrical connection.

Periodic inspection and removal of dirt and contaminants will ensure that equipment can be

operated safely.

Troubleshooting

1. Check if the power cord is plugged into an electrical outlet, if not, plug in.

2. Check if electricity to the main fuse is working

3. Error code shows on display

E1 Error on Display: Control unit overheat. Check installation clearances.

L1,2,3, shows in display, but no heat:Bulb is damaged. Arrange for replacement bulb with local

Dealer

CLEANING AND MAINTENANCE

Regular and careful cleaning helps your infrared heater operate efficiently for many trouble-free

years. To clean your heater, follow steps below:

1. Unplug the power cord for your safety before cleaning your appliance.

2. Make sure the heater is cool before continuing.

3. To keep the heater clean, the outer shell maybe cleaned with a soft, damp cloth. You may use a

mild detergent if necessary. After cleaning, dry the unit with a soft cloth. (CAUTION: DO NOT let

liquids enter the heater).

4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the

heater. This may cause damage or deterioration to the surface of the heater.

5. DO NOT immerse the heater in water

6. Wait until the heater is completely dry before use.

Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build up.

Use packaging carton to store.

ATTENTION:

1. Always disconnect the heater from the electricity supply and allow it to cool before attempting

to work on it.

2. If the heater has collected dust or dirt inside the unit or around the heating element, have to

unit cleaned by a qualified service agent. Do not operate the heater in this condition.

3. The only maintenance required is cleaning of the external surfaces of the heater.

4. Do not touch the heating element with bare fingers, as residue from your hand could affect the

life of the lamp. If it is accidentally touched, remove the finger marks with a soft cloth

moistened with mentholated spirit or alcohol.

5. Do not attempt to repair or adjust any electrical or mechanical functions on this heater.

6. The heater contains no user serviceable parts. Should the product suffer damage or breakdown,

it must be returned to the manufacturer or its service agent.

7. Damaged supply cords to be replaced by the manufacturer, service agent or similarly qualified

person in order to avoid hazard.

RECYCLING

At the end of the electrical products useful life it should not be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice

in your country.

Warranty Information

Or visit DrHeaterUSA.com/register-your-heater

Feedback

Love it? Help us make the product more for you.

Let us know with a customer review.

Please visit: https://www.amazon.com/review/review-your-purchases#

At Dr. Heater USA, we are committed to bringing top quality alternative & supplemental heating products to

our customers.

Note: There may be a trace of smoke or odor when the unit is first operated. Do not be alarmed. This

indicates a drop of oil fell on the interior coils during the manufacturing process. It will quickly evaporate and

should not recur.

How long is the warranty?

This heater comes with a ONE-YEAR LIMITED COMPONENT WARRANTY. If your unit does not appear to

be working properly, please contact our service center by calling 1-800-317-1688. Prior to your call, we

encourage you to visit our service related website www.DrHeaterUSA.com for troubleshooting tips and service

instructions if needed.

Dr. Infrared Heater

860 Mahler Rd

Burlingame, CA 94010

Tel: 1-800-317-1688

EMAIL: SERVICE@DRHEATERUSA.COM

Dr Heater USA

@DrHeaterUSA

Dr. Heater USA

Table des matières

Autres manuels DR. Heater Chauffage

DR. Heater

DR. Heater DR-PS11024 Manuel utilisateur

DR. Heater

DR. Heater DR-908 Manuel utilisateur

DR. Heater

DR. Heater DR-9FH2120 Manuel utilisateur

DR. Heater

DR. Heater DR-988 Manuel utilisateur

DR. Heater

DR. Heater DR-966 Manuel utilisateur

DR. Heater

DR. Heater DR-968H Manuel utilisateur

DR. Heater

DR. Heater Elite Series Manuel utilisateur

DR. Heater

DR. Heater DR-238EU Manuel utilisateur

DR. Heater

DR. Heater DR-978 Manuel utilisateur

DR. Heater

DR. Heater DR-368 Manuel utilisateur

DR. Heater

DR. Heater DR-368 Manuel utilisateur

DR. Heater

DR. Heater DR218-1500 Manuel d'instructions d'installation

DR. Heater

DR. Heater DR-838 Manuel utilisateur

DR. Heater

DR. Heater DR-999 Manuel utilisateur

DR. Heater

DR. Heater DR-966 Manuel utilisateur

DR. Heater

DR. Heater DR-975 Manuel utilisateur

DR. Heater

DR. Heater DR-998 Elite Series Manuel utilisateur

DR. Heater

DR. Heater DR-239 Manuel utilisateur

DR. Heater

DR. Heater DR-P130 Manuel utilisateur

DR. Heater

DR. Heater DR-122X4 Manuel utilisateur

DR. Heater

DR. Heater DR-910M Manuel utilisateur

DR. Heater

DR. Heater DR-928 Manuel utilisateur

DR. Heater

DR. Heater DR-968 Manuel utilisateur

DR. Heater

DR. Heater DR-222 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur