Dovpo Punisher 80 Manuel utilisateur
Size: 91.0mm X 43.0mm X 25.0mm
Material: Zinc Alloy
Surface: Rubber Paint
Specification
1. Operating Voltage: 3.3V - 4.2V.
2. Maximum Output Current: 28.5A.
3. Operating Wattage: 5.0W - 80.0W.
4. Temperature control range: 212°F - 572°F/100℃ - 300℃.
5. Temperature control coils working resistance range: 0.1Ω - 1.0Ω.
6. Standard atomizer working resistance range: 0.1Ω - 3.0Ω.
7. Operating Mode: Power Mode, Direct Mode, Ni 200 Temperature Control Mode,
Ti coil Temperature Control Mode, Ss316L Temperature Control Mode.
8. Short Circuit Protection
9. Low Voltage Protection
10. Overheat Protection
11. Battery-reversal Protection
12. Overtime Vaping Warning
13. Power-off memory function
14. Using single 18650 external battery
15. Charger Required: DC5V / 1A
16. Charging time: 3 - 5 hours
Operation Guide
Picture 1.1
0.21Ω
400Ni℉
80.0w
0.58Ω
80.0w
6.82v
0.58Ω
3.95V
0.0w
Picture 1.2 Picture 1.3
Battery Voltage
1. ON/OFF Battery Switch
By press the fire button 5 times quickly after install the battery, the screen will
display “DOVPO” and it leads you to the main interface. See picture 1.1 ( In Ni
200 coil temperature control mode ), see picture 1.2 ( In Titanium coil temper-
ature control mode ), see picture 1.3 ( In Ss316L mode), see picture 1.4 ( In
Power mode ) and see picture 1.5 ( In Direct Mode ).
0.21Ω
400 ℉Ti
80.0w
0.21Ω
400 ℉Ss
80.0w
Picture 1.4 Picture 1.5
Operation Guide
2. Auto Power-off / Manual Shutdown
2.1 The device will power-off automatically after 30 minutes no use, you need
restart the device by pressing the fire button 5 times quickly to vaping again.
2.2 When in standby mode, press the fire button 5 times quickly, the screen will
go dim after display“ SYSTEM OFF”.
3. Sleep Mode On/Off
The screen will go dim after 30 seconds of no activity. Wake up this device by
pressing any button when in Sleep Mode.
4. Start Vaping
4.1 See picture 4.1 below in Ni 200 Temperature control mode, Ni 200 coil available
only in this mode.
4.2 Titanium coil available only in Titanium coil Temperature control mode.
4.3 Ss316L coil available only in Ss316L Temperature control mode.
4.4 See picture 4.2 below in Power mode, standard coil available in this mode.
4.5 See picture 4.3 below in Direct mode, standard coil available in this mode.
Operation Guide
Picture 4.1
092
400Ni℉
395℉
093
49.0w
5.21V
Picture 4.2
Set Temperature
Real-time Temperature
Operating Voltage
095
3.45V
36.6w
Picture 4.3
Puff Counter
5. Wattage Adjustment
When in wattage mode, using the "+" or "-" button will allow you to increase or
decrease desired wattage by 0.1W. Holding either button will cause the wattage
to scroll more quickly.
6. Temperature Settings
When in either Temperature control mode, using the "+" or "-" button will allow
you to increase or decrease desired temperature by 1°F/1°C. Holding either
button will cause the temperature to scroll more quickly.
Operation Guide
7. Lock / Unlock
7.1 When in standby mode, press and hold both fire button and "-" button for 1.5s,
the screen will display “ KEY LOCK”, All functions will be disabled in Lock Mode,
and the screen will display “ Please Unlock” by pressing any button.
7.2 When in Lock mode, press and hold both fire button and "-" button for 1.5s,
the screen will display “ KEY UNLOCK”, the device switches to UNLOCK mode.
8. Work Mode Setting
When in standby mode, press and hold both "+" button and "-" button for 1.5s
will allow you to choose the Power mode, Direct mode, Ni 200 temperature control
mode, Ti coil temperature control mode, and Ss316L temperature control mode.
9. Celsius and Fahrenheit Setting
When in temperature control mode, using the "+" or "-" button will allow you to
set Celsius and Fahrenheit. When the Celsius and Fahrenheit value is the
maximum or the minimum one, by pressing the "+" or "-" button will lead you
to the other (Fahrenheit / Celsius) mode.
Operation Guide
10. Replace an Atomizer
When changing the atomizer the screen will ask " New Atomizer YES(+) NO(-) ",
press the "+" button to confirm that it is a new atomizer and will show the new
resistance. Press the "-" button will tell the device it is the same atomizer and
the resistance will be the same as before.
11. Clear Puff Counter
become zero, the device will recount in next time vaping. 999 is the Maximum
display puff counter.
12. Set Wattage in Temperature Control Mode
When in temperature control mode, press and hold both fire button and "+"
button for 1.5s, the wattage display in the top right corner will flicker, using the
"+" or "-" button will allow you to increase or decrease the wattage.
When in standby mode, press the fire button 3 times quickly, the puff counter will
Operation Guide
13.Temperature Control Mode
13.1 Temperature Control is available when using nickel 200 coil, Titanium Coil and
Ss316L coil.
13.2 The device will display the correct temperature only when use the correct coils
in the Temperature control mode accordingly.
13.3 Please ensure the nickel coil / Ti coil or Ss316L coil is under ambient temperature
before activating the Punisher 80, or it may read a wrong resistance value.
13.4 The Punisher 80 temperature control mode is associated with the wattage
mode. Wattage set in temperature control mode will limit the temperature
increase and output wattage. If the device temperature is the set one, it
will limit the maximum output wattage within the set wattage. If the set
wattage can not meet the set temperature, to ensure the vaping quality,
the device will auto adjust the wattage to a available temperature.
13.5 When in temperature control mode, the device will recognize the standard coil
automatically and the device will turn to wattage mode automatically.
Operation Guide
14. Overtime Vaping Warning
The device will force shut down by itself after 10 seconds of continuous firing.
15. Low Voltage Protection
15.1 If the battery voltage is lower than 3.3V, the device will stop working and the
screen will display “Please Charge”.
15.2 When power on and firing with a voltage lower than 2.5V the screen will display
“WEAK BATTERY”. If the battery capacity is full and display “WEAK BATTERY" .
This can be adjusted by using a low-drain/overused battery or it could be caused
by poor connection.
16. Short Circuit Protection
If the output end has a short circuit, the screen will show “SHORT”.
17. Overheat Protection
When the mainboard's temperature is too high the device will stop working and
the screen will display “TOO HOT”.
Table des matières
Autres manuels Dovpo Vaporisateur
Manuels Vaporisateur populaires d'autres marques
Storz & Bickel GMBH
Storz & Bickel GMBH Crafty Manuel utilisateur
Joyfect
Joyfect Freaky One Manuel utilisateur
SIGELEI
SIGELEI 213 FOG Manuel utilisateur
Eleaf
Eleaf Lemo 2 Manuel utilisateur
Vapor Brothers
Vapor Brothers VB Eleven Pen Manuel utilisateur
STORZ & BICKEL
STORZ & BICKEL VOLCANO CLASSIC Manuel utilisateur