dosatron D8RE2 Mode d'emploi
Page 1
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 3: Then, check to see if you feel suction on your nger.
Step 2: Unscrew and remove the suction hose nut and hose.
D8RE2 Troubleshooting - Part 1
This D8RE2 - 40 GPM Troubleshooting Part 1 will cover: The injector is clicking, but not
drawing the concentrate.
Scan the QR code to
watch our D8RE2 -
Troubleshooting video.
Step 1: Take a look at the strainer. If it is clogged clean it and
retest your Dosatron. If there is still no suction but the Dosatron is
clicking turn the water on.
Page 2
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
D8RE2 Troubleshooting - Part 1
Step 6: Press the air bleed button on the bell housing a few times
to release the pressure.
Step 5: After you reattach you should see the liquid begin
moving up the suction hose. If you don’t see liquid moving up the
hose or you don’t feel suction on your nger, turn the water off.
Step 4: If you feel suction, just cut a half inch off the top of the
hose and reattach. If the hose is cracked, ridged, or looks really
old just replace it.
Page 3
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 9: Unscrew the injection stem nut.
Step 8: Remove the suction hose. Set it aside.
D8RE2 Troubleshooting - Part 1
Step 7: Unscrew the suction hose nut.
Page 4
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 12: To change the plunger seal, pinch and roll it off
the plunger.
Step 11: Take a close look at the plunger seal for nicks, scratches,
or wear. If you see damage or don’t remember the last time you
changed the plunger seal, just replace it now (Part #: JDI121).
D8RE2 Troubleshooting - Part 1
Step 10: Pull the injection stem straight out from the body of the
injector.
Page 5
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 15: Then, reinstall the injection stem nut, hand tight.
Step 14: To reinstall the injection stem, align the notches in the
lower part of the blue body with the teeth on the top of the injection
stem assembly.
D8RE2 Troubleshooting - Part 1
Step 13: Install the new one into the groove on the plunger.
Page 6
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 18: Reinstall the nut hand tight.
Step 17: Pull the stem down slightly, rotate it and push it back up.
D8RE2 Troubleshooting - Part 1
Step 16: If the scale you prefer is not facing out, just loosen the
stem nut and remove.
Page 7
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
D8RE2 Troubleshooting - Part 1
Step 19: Your injector should now be drawing the concentrate.
Page 8
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 3: Grab the barb and pull the check valve assembly
straight out.
Step 2: Unscrew and remove the check valve nut.
Step 1: Remove the hose nut and hose, set aside.
D8RE2 Troubleshooting - Part 2
This D8RE2 - 40 GPM Troubleshooting Part 2 will cover: The injector is pushing water
down into the concentrate tank.
Page 9
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 4: To inspect the check valve parts, hold the assembly
and twist the white top guide one quarter turn counter
clockwise to remove.
D8RE2 Troubleshooting - Part 2
Step 5: Remove the spring and cone.
Step 6: Inspect all of the check valve parts. If they are dirty, you
may be able to soak, brush off, and re-install. If you see damage
or if you don’t remember the last time you changed these parts,
just replace them now (Part #: PJDI118).
Page 10
800-523-8499
www.dosatronusa.com
Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.
Step 9: Position the top guide over the shaft.
Step 8: Then slide the spring over the shaft.
Step 7: Insert the cone into the top of the barb.
D8RE2 Troubleshooting - Part 2
Autres manuels pour D8RE2
1
Autres manuels dosatron Équipement de laboratoire
dosatron
dosatron D128R Mode d'emploi
dosatron
dosatron D14MZ3000 Mode d'emploi
dosatron
dosatron D25RE2 Mode d'emploi
dosatron
dosatron D 25 F 1 Instructions de montage
dosatron
dosatron D14MZ2VFII Manuel utilisateur
dosatron
dosatron D14MZ2 Manuel de programmation
dosatron
dosatron D14MZ10 Mode d'emploi
dosatron
dosatron D14MZ3000AFII Manuel utilisateur
dosatron
dosatron D 25 F 1 Mode d'emploi
dosatron
dosatron D45RE15 Mode d'emploi
Manuels Équipement de laboratoire populaires d'autres marques
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuel utilisateur
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuel utilisateur
NI
NI PXI-5422 Manuel
Collomix
Collomix Aqix Manuel utilisateur
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur
Ocean Insight
Ocean Insight FLAME-NIR+ Manuel utilisateur
