DoorKing 1515 Manuel utilisateur

STAND ALONE DIGITAL LOCK

The 1515 can be mounted indoors/outdoors directly to a wall/pilaster or a DoorKing gooseneck mounting post (Optional). Do not mount the digital

lock to a moving gate, or immediately next to a gate panel or pedestrian gate. Continuous vibration from slamming gates and vibration can cause

damage to the unit over time. WARNING! If the digital lock is used to activate a vehicular gate operator, it must be mounted a minimum of 6 feet

away from the gate and gate operator, or in such a way that the user cannot come into contact with the gate or gate operator while using the digital

lock. Digital Lock MUST be properly grounded.

The master code MUST be programmed in from the built-in keypad AFTER installation is complete and BEFORE any programming takes place. Write down your

master code after it has been programmed in and store it in a safe place. There is NO way to retrieve the master code after it has been programmed in. If you forget it,

you will have to program in a new master code but all other pre-programed information will remain intact.

Installation

Program Master Code

Power

Supply

(included)

Optional Mounting:

Enclosure can be mounted

on a DoorKing gooseneck

mounting post (not

supplied). Run wires inside

gooseneck post.

Important:

After installation, the digital

lock will need to have the

Master Code programmed

in and be programmed for

desired features using the

built-in keypad or android

smart phone (see below

and next page).

DoorKing Part Number

120 S. Glasgow Avenue

Inglewood, California 90301 U.S.A.

1515-080

DoorKing’s 1515 Digital Lock is designed to manage an access point without needing an access control system. The digital lock can store up to

400 codes in memory for “Momentary” or “Hold Open” entry. It’s relay output can control an electric strike, magnetic lock or gate operator.

Request to Exit input (Free exit) allows an exit button to open the door or gate. Program the digital lock with the built-in keypad or an ANDROID

smartphone using the DKS Digital Lock Manager app with NFC - Near Field Communication programming. You can use an Android smartphone

and the DKS Smart Open app (free download at Google Play Store) to open the door or gate that is connected to the 1515. It can be programmed

for low power mode (less than 1 mA current draw) for use with solar applications.

789

456

123

Input:

120 V60 Hz

Output:

16.5VAC20 VA

Push Button

(Free Exit)

Electric

Strike

Maglock

Door Control

Required NC

EXIT

PUSH TO

Separate

Power

Supply

Separate

Power

Supply

12345678

1515-010

MASTER

CODE

12-24 VAC OR NEG (-) DC Power

12-24 VAC OR POS (+) DC Power

Earth Ground

Request to Exit Input

Relay - Normally Open (NO)

Relay - Normally Closed (NC)

Relay - Common (C)

Power

Supply

Gate

Operator

Gate Control

MASTER

CODE

Step 1. Open the digital lock to access the Master Code push button on the circuit board.

(1515 must have power) Press the Master Code push button ONCE.

Step 2. Enter a four-digit master code using the built-in keypad, then press (A short beep will be heard).

Step 3. Close the digital lock. Write down master code and keep it in a secure place.

Lighted

Built-In

Keypad

NFC Antenna

Mounting: Use the existing holes in the cabinet to

mount digital lock. Run conduit inside or outside

of wall/pilaster if desired. Use appropriate

hardware to mount the cabinet (Not supplied).

Be sure that the mounting hardware does not

protrude into the cabinet where it could cause a

short. Clean any debris out of cabinet that could

cause a short.

Note: A gooseneck mounting post anchored in

concrete does NOT make a good ground.

1515 065-D-5-15

02 - Entry Codes

1. Press *0 2 and enter the four-digit MASTER CODE. [*0 2 _ _ _ _ (beep)]

2. Enter a 4 or 5 digit entry code (whichever was programmed in 01- setup above),

then press

*. [ _ _ _ _ (_)*(beep)]

3. Repeat step 2 to add additional entry codes.

4. Press 0 # together (Beeeeeep) to exit programming. [ 0 # (beeeeeep)]

07 - Hold Open Codes

1. Press *0 7 and enter the four-digit MASTER CODE. [*0 7 _ _ _ _ (beep)]

2. Enter a 4 or 5 digit hold open code (whichever was programmed in 01- setup above),

then press

*. [ _ _ _ _ (_)*(beep)]

3. Repeat step 2 to add additional hold open codes.

4. Press 0 # together (Beeeeeep) to exit programming. [ 0 # (beeeeeep)]

09 - Erase Individual Entry Codes or Hold Open Codes

1. Press *0 9 and enter the four-digit MASTER CODE. [*0 9 _ _ _ _ (beep)]

2. Enter the 4 or 5 digit entry code or hold open code to be erased, then press *.

[ _ _ _ _ _ *(beep)]

3. Repeat step 2 to erase additional entry codes or hold open codes.

4. Press 0 # together (Beeeeeep) to exit programming. [ 0 # (beeeeeep)]

03 - Entry Code Strike Time

Valid two-digit strike time values are 00-99. 00 = 1/4 sec 01 = 1 sec 99 = 99 secs.

1. Press *0 3 and enter the four-digit MASTER CODE. [*0 3 _ _ _ _ (beep)]

2. Enter a two-digit relay strike time, then press *. [ _ _ * (beep)]