Doka Staxo 40 Manuel utilisateur
© by Doka GmbH, A-3300 Amstetten
999284802 08/2018
en-GB
-
The Formwork Experts.
Staxo 40 shifting wheel
Art. n°: 582218000 | 2010 models onward
Original Operating Instructions
Please retain for future reference
© by Doka GmbH, A-3300 Amstetten
2999284802 - 08/2018
Original Operating Instructions Staxo 40 shifting wheel
Basic drawings of product
a ... min. 1158 mm - max. 1478 mm (adjusting range: max. 320 mm)
b ... 574 mm / 837 mm
c ... 456 mm
d ... 160 mm
e ... 110 mm
Data on rating plate
Designation: Staxo 40 shifting wheel
Art.n°: 582218000
Dead weight: 21,7 kg
Max. load: 500 kg
Year of manufacture: see rating plate
Intended use
The Staxo 40 shifting wheel is classified as a lifting
appliance. It may be used for horizontal reposition-ing
of Doka load-bearing towers Staxo 40, either with or
without formwork (intended use).
With it, the following functions can be carried out:
▪ Lifting
▪ Wheeling
▪ Lining-and-levelling
▪ Lowering
a
c
b
d
e
NOTICE
▪ Other use or use not in conformity with that
stated above is non-intended use and
requires the prior written approval of the
Doka company!
▪ It is forbidden to lift other manufacturers'
load-bearing towers with it.
Permissible total weight of each unit for repositioning:
1000 kg (max. 4 Staxo 40 shifting wheels per unit)
NOTICE
When repositioning load-bearing towers that
include standard superstructures, remember:
Ratio b:h = max. 1:3, with 'b' being the narrow-
est side.
Custom constructions must be statically veri-
fied!
98024-322-03
b
b
h
Original Operating Instructions Staxo 40 shifting wheel
3999284802 - 08/2018
Maintenance & inspection
▪ Repairs may only be carried out by the manufac-
turer!
▪ Doka accepts no liability for products that have been
altered!
Before every use
➤Check for any signs of damage or visible deforma-
tion.
At regular intervals
▪ Inspection of lifting accessories must be performed
at regular intervals by an expert in conformity with
national statutory provisions.
Unless otherwise stipulated, such inspection must
be carried out at least once a year.
Storage
▪ Store lifting accessories in a dry and well ventilated
place, protected from the weather and from all corro-
sive substances.
Preconditions for use:
Fixing to the load-bearing tower
Preparations on the load-bearing tower
➤In cases where the screw-jack feet are extended a
long way, reduce the extension length of the screw-
jack feet to dimension 'a'.
➤Use the anti-dropout locks to fix the screw-jack feet
to the frames.
a ... max. 40 cm
Lifting accessories that do not meet the fol-
lowing criteria must be withdrawn from use
immediately:
▪ No deformation.
▪ No cracks or notches.
▪ No damage due to the influence of heat.
▪ Rating plate must be in place and clearly
legible
NOTICE
▪ There must be a flat, firm (e.g. concrete),
adequately dimensioned floor that is capa-
ble of supporting the load.
▪ Max. permitted inclination of trackway: 2%
The permissible inclination of the trackway
must be determined by statical calculation
(risk of overturning, rolling forces).
▪ Either bridge any openings in the floor with
sufficiently strong planking/boards secured
so that they cannot slip away to either side,
or close off openings with sufficiently strong
side railings!
▪ Keep the travel route clean and free of any
obstacles.
▪ It is only permitted to travel Doka load-bear-
ing towers that have been braced in accord-
ance with the assembly plans and erection
rules given in the User Information booklet.
AStaxo 40 screw jack foot
BStaxo 40 anti-dropout lock
CBasic frame Staxo 40
92848-200-02
a
A
B
C
4999284802 - 08/2018
Original Operating Instructions Staxo 40 shifting wheel
Preparations on the shifting-wheels
Adjust the shifting-wheels to the Staxo 40 frames
of the bottom "storey" of the tower:
➤Fix the adjusting bracket in the required position
using a D16/125 bolt, and secure this with a linch pin.
Position of the adjusting bracket for:
Mounting the shifting-wheels to the load-
bearing tower
➤Bolt the shifting-wheel onto the Staxo 40 frame (in
the direction of the frames) with two D16/125 bolts,
and secure each of these with a linch pin.
Wheeling
Raising the load-bearing tower
➤Use the screwjack mechanism on the shifting-wheel
to raise the load-bearing tower max. 5 cm off the
ground.
b ... max. 5 cm
DAdjusting bracket
ED16/125 bolt
FLinch pin
▪ 0.90m frames
▪ upside-down 1.80m frames
▪ 1.20m frames
▪ 1.80m frames
92848-200-03
D
E
F
92848-202-01
92848-202-02
ED16/125 bolt
FLinch pin
GFixing positions in the Staxo 40 frame
HHandle of the shifting-wheel screwjack mechanism
Quick lowering of the swivel castor:
1) Open the split nut of the shifting-wheel by
releasing its integrated quick-locking
device.
The screwjack mechanism plus swivel
caster are now lowered to the ground.
2) Close the split nut again and fix it with the
quick-locking device.
92848-201-01
E
E
F
F
G
G
92848-200-01
92848-203-02
b
H
Original Operating Instructions Staxo 40 shifting wheel
5999284802 - 08/2018
Wheeling the load-bearing tower
b ... max. 5 cm
Crane-lifting of load-bearing towers with
shifting-wheels mounted to them
➤Check that the shifting-wheels are properly fixed to
the load-bearing tower.
Lowering the load-bearing tower
➤First lower the load-bearing tower onto the ground by
turning the screwjack mechanism in the shifting-
wheel.
Declaration of conformity
NOTICE
▪ Particular care is needed with:
- height offsets
- steps
- floor holes and wall openings
- strong wind
▪ It is forbidden for any third persons to linger
in the immediate danger zone!
▪ Exercise caution regarding the risk of over-
turning (particularly in strong wind).
▪ It is forbidden to use any mechanical assis-
tance during the wheeling operation!
▪ Take care to start moving gently, and to
exert a constant, uniform pull.
▪ Max. speed 4 km/h (walking pace)
▪ Special care is needed when travelling
across shoulders in the ground (no sharp-
edged shoulders, max. shoulder-height
15 mm).
▪ For longer breaks between operations, or
when the the load-bearing tower is perma-
nently parked, take the load off the shifting-
wheels (by lowering the tower to the
ground).
WARNING
➤"Passenger transportation" is forbidden!
➤Before the repositioning operation, remove
any loose items (e.g. fitting-boards) from the
load-bearing tower and formwork.
WARNING
Risk of overturning!
➤The load-bearing tower may only be raised
by max. 5 cm in order to be travelled.
92848-203-01
b
Follow the directions for resetting by crane
(slinging points etc.) in the "Staxo load-bearing
tower 40" User Information booklet.
Check to make sure that all the bolts are
secured by linch pins.
NOTICE
The split nut must not be opened when loaded!
EC Declaration of Conformity
pursuant to EC Directive 2006/42/EC.
The manufacturer declares that by reason of its conception and
design, the following product
Staxo 40 shifting wheel, Art. n° 582218000
conforms – in the version marketed by ourselves – to the pertinent
fundamental health and safety stipulations of the relevant EC Direc-
tives.
The following harmonised Standards were applied:
▪ EN ISO 12100:2010
▪ EN 349:1993+A1:2008
Person authorised to compile technical documentation
(pursuant to European Directive on Machinery Annex II):
Dipl.-Ing. Ludwig Pekarek
Josef Umdasch Platz 1
A-3300 Amstetten
Amstetten, 07/08/2018
Doka GmbH
Josef Umdasch Platz 1
A-3300 Amstetten
Dipl.-Ing. Ludwig Pekarek
Executive Manager
Dipl.-Ing. Peter Reisinger
Authorised Officer, Head of Engi-
neering
Autres manuels pour Staxo 40
1
Table des matières
Autres manuels Doka Système de levage
Manuels Système de levage populaires d'autres marques
morse
morse 82H-124 Manuel utilisateur
Braun
Braun NL955 Series Manuel utilisateur
haacon
haacon 1889.10 Manuel utilisateur
Protekt
Protekt AT 252 Manuel utilisateur
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manuel utilisateur
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manuel utilisateur
Genie
Genie Z-60/34 Manuel utilisateur
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuel utilisateur
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuel de programmation
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuel de programmation
