Dnake DK230 Manuel utilisateur
Model: 280SD-C12
280SD-R2
280SD-R5
Quick Start Quide
Door Station
The picture is only a schematic diagram. The actual product shall prevail.
USER MANUAL
DK230
Wireless
Doorbell
Please follow the user manual for correct installation and
testing. If there is any doubt please call our tech-supporting
and customer center.
Our company applies ourselves to reformation and
innovation of our products. No extra notice for any change.
The illustration shown here is only for reference. If there is
any difference, please take the actual product as the
standard.
The product and batteries must be handled separately from
household waste. When the product reaches the end of
service life and needs to be discarded, please contact the
local administrative department and put it in the designated
collection points in order to avoid the damage to the
environment and human health caused by any disposal. We
encourage recycling and reusing the material resources.
REMARK
CATALOG
Package Contents ...................................................1
Pictures.....................................................................3
Basic Operation.......................................................4
System Configuration ............................................5
System Diagram......................................................6
Installation ...............................................................9
Safety Instructions ................................................13
Product Features......................................................1
Package Contents ....................................................1
Pictures.....................................................................2
Installing Batteries ...................................................4
Installation Instruction .............................................5
Diagram ....................................................................6
Settings.....................................................................8
Engineering Mode..................................................17
Operations..............................................................19
Technical Parameters.............................................21
Installation & Usage...............................................23
Safety Instructions .................................................25
PRODUCT FEATURES
PACKAGE CONTENTS
Door Camera Bracket
Battery Cover Cable Cover
Screws User Manual
Screw Wrench
Contents camera of door
1
2.4" TFT LCD display
Video resolution: 320x240, with 15 frames per second
Wide angle lens and LED for night vision
Long standby door camera (battery or DC 12V)
Waterproof door camera IP65
Microphone and speakerphone
Basic video intercom, monitoring, remote unlocking and tamper alarm
feature
Adjustable brightness and talking volume
Support up to 2 door cameras and 2 indoor monitors
Transmitting distance: up to 400m range in open area
DIY installation to save labor cost
Package Contents
Please make sure the package contains the following items:
Lithium Battery
Power Adapter
(12V, 500mA)
Indoor Monitor
Contents of indoor monitor
PICTURES
Door Camera
2
Charger Base
LED Lights
Sensor Light
Speaker
Microphone
Call Button
Camera
Indoor Monitor
3
Charger
LCD Display
Navigation Key
Right Soft Key
Monitor/ Snapshot
Power/ End Key
Left Soft Key
Unlock Key/
Charger LED
Accept Key
Microphone
Speaker
Battery
Compartment
Cover
Charging Pins
Charger Base
INSTALLING BATTERIES
Indoor Monitor
The rechargeable lithium battery (3.7V, 1100mA) comes with indoor monitor.
Install the battery before use.
1.
2. Insert new battery as indicated, matching correct polarity(+,-).
3. To replace the battery, slide the cover up until it snaps in place.
Notes:
1. To activate battery please remove protective cover from the battery prior
to use.
2. The battery needs to be replaced if it doesn't recover its full storage
capacities after recharging.
3. When replacing the battery, make sure using good quality re-chargeable
lithium battery. Never use other battery or conventional alkaline battery.
4
Lithium battery
Battery case
Battery compartment cover
2
1
Protective cover
1. Call indoor monitor
In standby mode, press the call button on door station to call indoor
monitor. During the call, press the call button on door station again to end
the call. If the call fails or indoor monitor is busy, door station will emit a
beep.
2. Unlocking by card
Put the registered IC card on card reader area of the door station. If IC card
has been authorized, after unlocking the door by card, the system will issue
a voice message that "the door has been opened", otherwise it will emit a
beep.
Door Camera
1. Install two 1.5V size C batteries (not supplied) into the battery
compartment or connect with DC 12V power adapter to turn on the door
camera.
2. Drill four screws to fix the battery cover up.
Screw
Battery Cover
Battery
5
INSTALLATION INSTRUCTION
Indoor Monitor
Connect the DC power adapter to the power jack of the charger, then plug
the DC adapter into a standard AC wall outlet.
Charging Indoor Monitor
Before initial operation, ! Important Note: YOU SHOULD FULLY CHARGE
THE INDOOR MONITOR for about 5 hours.
To charge the indoor monitor, please place it on the charger base.
6
DIAGRAM
Connection Mode 1
DC Power Supply
GND
BAT+
EX-BUT
DC9-12V
BAT+(Optional)
NO
COM
NC
GND
DC9-12V
Backup Power
Lock
Connection Mode 2
GND
For normally-open lock
+
+-
-
DC power
for Lock
The maximum output
current of relay can be 1A.
Lock
For normally-closed lock
+
--
+
The maximum output
current of relay can be 1A.
Door Camera
Door Camera
DC power
for Lock
DC9-12V
BAT+(Optional)
NO
COM
NC
GND
GND
BAT+
DC Power Supply
Backup Power
Note: The door camera can be powered by the batteries or the power
adapter adapter The (not included). Do not use batteries and power .
monitoring feature is available by default when the door is camera
powered by power adapter. If the door is powered by batteries, the camera
monitoring feature is not available until the power mode is changed to
power consumption mode (see page 19).
EX-BUT
GND
DC9-12V
Door Camera
1. After wiring from the connection terminal, tighten the cable. Drill the
screws on the cable cover of the connection terminal.
Cable cover
Cable
2. Choose a proper location for the door camera. Be sure to consider the
average height of visitors. Drill screws to fix bracket on the wall. Hang the
door camera on the bracket. Drill screws to fix door camera and finish the
installation.
Waterproof EVA Pad
Installation
7
InstallationInstallation Door camera
Installation screws
Installation screw
Bracket
Plastic expansion Pipe
Mounting box
Table des matières
