Dj power H-S6 Manuel utilisateur

1 BEFORE YOU BEGIN

1.1 What is included

1 × H-S6 snow machine

1 × power cord

1 × fluid hose

1 × 20L tank

1 × 10M directional hose

1 × waterproof cover

1 × wireless remote

1 × user manual

1.2 Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts

are in the package and are in good condition.

If the box or the contents (the product and included accessories) appear damaged from

shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In

addition, keep the box and contents for inspection.

1.3 Symbols

Symbol

Meaning

Caution

Critical installation, configuration, or operation information. Not following these instructions

may make the product not work, cause damage to the product, or cause harm to the operator.

Important

Important installation or configuration information. Failure to comply with this information

may keep the product from working correctly.

Information

Useful information.

1.4 Disclaimer

The information and specifications contained in this User Manual are subject to change

without notice. DJPOWER assumes no responsibility or liability for any errors or omissions

1.5 Safety Notes

Please read the following Safety Notes carefully before working with the product. The notes

include important safety information about installation, usage, and maintenance.

1.5.1 Personal Safety

• Always connect the product to a grounded circuit to avoid the risk of electrocution.

• Make sure that children, unauthorized people and animals do not obtain access to the

machine.

1.5.2 Mounting and Rigging

• This product can be used indoors and outdoors！ To prevent risk of fire or shock, do not

expose the product to rain or moisture.

• CAUTION: When transferring product from extreme temperature environments, (e.g. cold

truck to warm humid ballroom) condensation may form on the internal electronics of the

product. To avoid causing a failure, allow product to fully acclimate to the surrounding

environment before connecting it to power.

• Do not mount the product on a flammable surface (linoleum, carpet, wood, paper, carton,

plastic, etc.).

• Do not use in a confined space. Always install the product in a location with adequate

ventilation, at least 20 in (50 cm) from adjacent surfaces.

• Be sure that no ventilation slots on the product’s housing are blocked or clogged by dust.

If necessary, remove the dust.

1.5.3 Power and Wiring

• Always make sure that the voltage of the outlet to which you are connecting the product is

within the range stated on the decal or rear panel of the product.

• Make sure the power cord is not crimped or damaged.

• Never connect this product to a dimmer pack or rheostat.

• Never disconnect the product from power cord by pulling or tugging on the cord.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use

completely disconnect the product from power via breaker or by unplugging it.

1.5.4 Operation

• Do not operate this product if you see damage to the housing or cables. Have the

damaged parts replaced by an authorized technician at once.

• Do not use the product as a space heater.

• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at

higher temperatures.

•Do not cover the ventilation slots when operating to avoid internal overheating.

•Do not cover or plug the output nozzle during operation.

• Wipe up spitted fluid immediately. Moisture – also fluid – can destroy the electric.

• Never carry the product by the power cord or any moving part. Always use the handles of

the machine.

•Drain the tank before transporting the product. Bubble fluid or the fog fluid tanks

shall be used for the relevant fluid only.

• Always disconnect the product from the power source before cleaning.

• In the event of a serious operating problem, stop using the product immediately.

• Snowflake water is not edible. Swallowing snowflake water may result in risk of damage to

your health. Please store snowflake water in a safe indoor place. In case of contact with

eyes or if swallowed, seek medical advice immediately.

• This product contains no user-serviceable parts. Any reference to servicing in this User

Manual will only apply to properly trained, certified technicians. Do not open the housing

or attempt any repairs which can lead to damage or malfunction.

•Use only DJPOWER Consumable. Snow fluid are recommended.

Keep this User Manual for future use. If you sell the product, be sure that the

purchaser receives this document.

2INTRODUCTION

2.1.1 Description

H-S6 is a convenient ultra-quiet snow machine launched by DJPOWER, which can pack

accessories, pipelines, and consumables into the flight case. This machine improves the

disadvantages of the traditional snow machine hanging high. It has a 10M hose (can be

extended to 20 meters), which can be extended to higher point or used at a distance,

equipped with a 20L tank capacity. It is enough to supply long-term activity performances,

greatly saves manpower, make the operation more humanized. H-S6 has powerful functions

such as timing quantitative, manual control, wireless remote control and DMX control, with

high-power fan, adjustable snow output, to meet any large realistic snow effect you want.

2.1.2 Features:

• All the accessories can be put in one flight case, convenient for transportation

• A 10M hose (can be extended to 20 meters) can be extended to higher point or used at a

distance

• 20L big capacity tank, avoid adding consumables frequently.

• With high-power fan, adjustable snow output, to meet any large realistic snow

• Use only DJPOWER high-quality PRO-X.2 snow liquid.

2.1.3 Product Overview

2.1.4 Production Dimensions

3 TECHNICAL SPECIFICATIONS

AC power

Voltage

AC 220-240 V, 50/60 Hz

Breaker Type

Overload Protector

Breaker data

10A/250V

Total Power

850W

Tank capacity

Capacity

20 L

Output

Adjustable Output

√

Fluid Consumption Rate

Appr. 2.5min/L

Placement &

Mounting

Lie flat

√

Keep upright

√

Side lay (do not cover the

radiating holes)

√

Hang upside down

√

Hang up

√

Control

Manual control

√

Wireless remote control

W-7

Wired control

K-2

Control Protocol

DMX512

DMX Channel

Consumable

PRO-X.2 or PRO-X Snow Fluid

Weight &

Dimensions

Net weight

34.7 kg

Gross weight

38.2 kg

Flight case dimensions

593 × 552 × 622 mm

Packing dimensions

655 × 610 × 665 mm

4 INSTALLATION SETTING

4.1.1 AC Power supply

H-S6 has a fixed voltage power supply, which can be used according to the specific model AC

220 V-240 V, 50/60 Hz.

To determine the power requirements of the machine (circuit breaker, power outlet and

wiring), please refer to the values listed on the machine panel label, or refer to the machine

specification data. The listed values represent the average current consumption of the

machine under normal conditions.

Always connect the machine to a protected circuit (circuit breaker or fuse). Make

sure that the machine is connected to a grounded power plug to avoid electric

shock or fire.

Never connect the machine to a rheostat (variable resistor) or dimmer circuit, even if

the rheostat or dimmer channel is only used as a 0 or 100% switch.

4.1.2 Reset the overload protector

This machine is equipped with resettable overload protector. If the overload protector trips,

the machine will be disconnected from the power source.

• Disconnect the machine from the power source.

• Wait 15 minutes for the machine to cool down.

• After 15 minutes, press the button of the overload protector to reset it.

•Plug the machine back into the power outlet and continue to use it as recommended.

4.1.3 Installation Notes

• Use mounting brackets or hanging clamps to mount the nozzle.

• Confirm that the installation site, fixed joints and slings can support more than 10 times the

weight of the nozzle.

• Make sure there are no flammable materials around.

• When installing the nozzle, be sure to use a safety rope that can support more than 10

times the weight of the nozzle.

• Please install the nozzle in a well-ventilated place.

• When choosing the installation location of the nozzle, please take the convenience of

replacing the nozzle and regular maintenance into consideration

4.1.4 Adjustable Mounting Bracket

Adjust mounting bracket by loosening screws, set the nozzle to desired angle and tighten

the screw to finish adjustment. Illustration below demonstrates how to adjust mounting

bracket

Use screws for surface mounting or clamps for truss mounting

10M Hose Extension (Optional)

The maximum hose length is 20 meters. Illustration below demonstrates how to connect

extension hose

5 WORKING WITH THE H-S6

5.1.1 Preparations

Before operating the machine, prepare according to the following steps:

Step 1: After checking that the machine and accessories are not damaged, place the machine

on a flat surface with at least 50 cm of space around the machine.

Step 2: Pour the PRO-X.2 snow fluid into the tank, taking care not to fold the tube. Damage

caused by the use of other liquids is not covered by the warranty.

Step 3: Connect the machine to the power. Before connecting, please confirm whether the

required power indicated on the technical label on the back of the machine is consistent with

the power supply.

Be sure to link the machine to a protected circuit and make sure it is properly grounded to

avoid the risk of electric shock.

Step 4: Start the machine and press the [VOLUME]/[DOWN] button to make the machine start

outputting snow.

Step 5: To turn off the unit, press the [STOP] button and turn the power supply to the OFF

position

5.1.2 LCD Control

This LCD display is optional in Chinese and English, which is convenient for customers to

operate.

• The condition to meet this mode is: disconnect the DMX signal (when the DMX signal is

connected, this control mode is invalid).

• The LCD controller contains 4 buttons:

Buttons

Function

<MENU>

Used to change pages (different pages set

different states)

▲

Add and reuse the "TIME" key (timed

output function)

▼

Decrease, reuse the "volume" key (smoke

output function)

<ENTER>

Confirm/exit, reuse the "STOP" key

5.1.3 MENU page

Press FUNCTION button, there are 11 pages as below:

LCD display

Description

Value Range

Setting

page

Ready To Fog

TOPCAT H-S6

It shows that the machine is ready to

work

Interval Set

5 s

Snow output interval setting (the range

is from 5 to 200 seconds)

5～200s

Duration Set

5 s

Snow output duration setting (the

range is from 5 to 200 seconds)

5～200s

Timer Out

100%

Snow output under the TIMER mode

setting (the range is from 1% to 100%)

1～100%

Volume Out

100%

Snow output under VOLUME mode

setting (the range is from 1% to 100%)

1-100%

Fan Speed

100 %

Fan volume setting (the range is from

1% to 100%) and with strong wind mode

1-100%

DMX512 ADD

The seventh page, setting DMX

channel

1 - 512

Wireless Set

ON/OFF

Setting the wireless remote control, can

choose ON/OFF setting

ON/OFF

Clear remote data

ENTER

The wireless remote control matching

data clearing page, press the ENTER

key on this page to confirm the

clearing. After clearing the remote

control matching data, the previously

matched remote control will not be

Table des matières

Autres manuels dj power Matériel de DJ

dj power

dj power DSK 2000 Manuel utilisateur

dj power

dj power XUN V-5 Manuel utilisateur

dj power

dj power TOPCAT HF-90 Manuel utilisateur

dj power

dj power R-7 Manuel utilisateur

dj power

dj power djv DC-2 CO2 CONFETTI FALL Manuel utilisateur

dj power

dj power DFZ 700 Manuel utilisateur

dj power

dj power R-6 Manuel utilisateur

dj power

dj power V-1 Manuel utilisateur

dj power

dj power X-4LED Manuel utilisateur

dj power

dj power Hazer DHZ-660 Manuel utilisateur

dj power

dj power V-4 Manuel utilisateur

dj power

dj power V-1 Manuel utilisateur

dj power

dj power V-3 Manuel utilisateur

dj power

dj power R-4 Manuel utilisateur

dj power

dj power djv DC-3 Manuel utilisateur

dj power

dj power S-2 Manuel utilisateur

dj power

dj power FLAME MACHINE HF-210 Manuel utilisateur

dj power

dj power LED Flame Light F-6 Manuel utilisateur

dj power

dj power djV PRO STAGE EFFECTS DC-1 Manuel utilisateur

dj power

dj power H-8 PRO Manuel utilisateur

dj power

dj power WP-2 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur

dj power H-S6 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques