Ditek DEFLECTOR Series Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Ditek Parafoudre

Ditek

Ditek DTK-DF120S1 Manuel utilisateur

Ditek

Ditek DTK-DP4P Manuel utilisateur

Ditek

Ditek DTK-SNAP-LITE Series Manuel utilisateur

Ditek

Ditek ZEUS Series Manuel utilisateur

Ditek

Ditek DTK-110C6A Guide de configuration

Ditek

Ditek DR Series Manuel utilisateur

Ditek

Ditek D200-277/4803Y Guide de configuration

Ditek

Ditek DTK-RM12ETH Guide de configuration

Ditek

Ditek DTK-DF240S12 Manuel utilisateur

Ditek

Ditek DTK-TSS2 Manuel utilisateur

Ditek

Ditek D200-2403D Guide de configuration

Ditek

Ditek D50-277/4803Y Guide de configuration

Ditek

Ditek D200-4803D Guide de configuration

Ditek

Ditek D200-120/2401 Guide de configuration

Ditek

Ditek DTK-RM12POE Guide de configuration

Ditek

Ditek DTK-WM4 Series Guide de configuration

Ditek

Ditek DTK-RM12POE Guide de configuration

Ditek

Ditek DTK-120/240CM+ Guide de configuration

Ditek

Ditek DTK-TSS4D Guide de configuration

Ditek

Ditek DTK-TSS5 Manuel utilisateur

Ditek

Ditek D50-2403D Guide de configuration

Ditek

Ditek D200-120/2083Y Guide de configuration

Ditek

Ditek DR Series Manuel utilisateur

Ditek

Ditek DTK-240X12 Manuel utilisateur

Manuels Parafoudre populaires d'autres marques

ELAC

ELAC ProteK PR91-W Manuel utilisateur

Tsubaki

Tsubaki TSM4000M1 Manuel utilisateur

QVS

QVS PP134C Manuel utilisateur

CyberPower

CyberPower CSP604T Manuel utilisateur

Davis Instruments

Davis Instruments Radio Surge Protector Manuel utilisateur

M-system

M-system MGA-100 Manuel utilisateur

CyberPower

CyberPower CSP706T Manuel utilisateur

CyberPower

CyberPower B300WRC1 Manuel utilisateur

M-system

M-system MGD-24 Manuel utilisateur

Leviton

Leviton 51120-3R Manuel utilisateur

Panamax

Panamax MAX 5400-EX Manuel utilisateur

CyberPower

CyberPower B1006T Manuel utilisateur

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manuel utilisateur

Minuteman

Minuteman MMS7120RCT Manuel utilisateur

Leviton

Leviton 52412-DS3 Manuel utilisateur

Savio

Savio LZ-07 Manuel utilisateur

Siemens

Siemens HNM3M120 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manuel utilisateur

DTK-DF240S1

User Guide

DITEK CORPORATION

One DITEK Center 1720 Starkey Road Largo, Fl 33771

1-800-753-2345 www.diteksurgeprotection.com

CAUTION: By removing the cover, you will be exposed to live metal parts and there is

a risk of electrocution.

WARNING: Removing the cover should only be performed by a licensed electrician.

WARNING: When the DTK-DF240M module has gone end of life, or is missing, the

base is susceptible to damage from surge energy. Make sure you always have a

spare module available. No substitutions shall be permitted.

The DTK-DF240S1 is a series connected Surge Protective Device with a replaceable surge

module.The LED indicators on the top face of the DTK-DF240M provide power, ground and

surge module health status. When the DTK-DF240M surge module has gone end of life, the

large “REPLACE” RED LED will illuminate and the “GOOD” LED will turn off. Also, the audi-

ble alarm will sound to provide an extra alert as to the surge module’s health. To silence the

alarm, remove the dead module and replace it with a new, unused module. If a new module

is not available, the alarm can be silenced by pressing the tactile switch, located at the

bottom of the enclosure, into BYPASS mode for 24 hours. The red polarizing keys ensure

that the correct voltage module will mate with its corresponding base.

DTK-DF240M (Surge Module)

DTK-DF240S1 (240V 20A Series Surge Protective Device)

CAUTION: Risk of Electric Shock-Only intended for installation in accordance

with National Electric Code, ANSI/NFPA-70, Article 398.

Warning: Turn power off at the main circuit breaker panel before beginning install.

Note: Connect this device in series between the 240VAC power supply and the alarm

panel, or branch panel 240VAC inputs. Use 12 AWG Stranded, Cut only conductors

with a 3/8” strip length when terminating the wires at the power lugs. The conductors

used to connect the SPD, to the line or bus and to ground, shall not be any longer than

necessary and shall avoid unnecessary bends.

1. Remove cover and save screws.

2. Connect the Ground (green or bare) to the EARTH terminal.

3. Connect the Neutral (white) supply wire to the NEUTRAL terminal on LINE-IN side.

4. Connect the Phase (black) supply wire to the LINE terminal on LINE-IN side.

5. Connect the Ground, Neutral and Phase wires from the LOAD-OUT side to the alarm panel, or

branch panel AC inputs.

Note: Tightening torque for the 240VAC power connections is 20 in. lbs.

6. Use appropriately sized conduit fittings and conduit to protect wiring, replace cover.

7. After all connections have been made and no hazards exist, insert DTK-DF240M surge module

and restore power.

DITEK CORPORATION

One DITEK Center 1720 Starkey Road Largo, Fl 33771

1-800-753-2345 www.diteksurgeprotection.com

191604 INT-100173-001 Rev 1

DTK-DF240S1

(Mounting Dimensions)