DITEC GOL4 Manuel utilisateur

www.ChronoRemoteControl.com

Manual

DITEC: GOL4 et GOL4C

Coding of a remote controls DITEC GOL4 (white LED) et GOL4c

(red LED):

Ditec remote controls GOL4 and GOL4C are not compatible with each other:

Coding based on a remote already in use:

1) Simultaneously press buttons CH1 and CH2 of a new remote control and hold

for 5 seconds. The red LED turns on.

2) Within 10 seconds, take GOL4C or BIXLS2 (old model) remote already in use.

Hold one button and put the remote controls together as showed on the pictude

below (The front of the old remote should touch the space between the buttons

of the new one.).

3) The LED of the new remote control flashed 3 times as a sign of a successful

operation.

www.ChronoRemoteControl.com

Registration of a code on a GOL4C remote (equivalent to coding using the dip-

switches of the old BIXLS2 model):

1) Simultaneously press buttons CH1 and CH2 of a new remote control and hold

for 5 seconds. The red LED turns on.

2) Within 10 seconds, copy the code made of 10 numbers using the CH1 button as

0 (OFF) and CH2 button as 1 (ON).

3) Once the 10 numbers are inserted, the LED blinks 3 times indicating the end of

the registration procedure.

4) Try the new remote control.

www.ChronoRemoteControl.com

Registration of remote controls using BIXR1/ BIXR2 radio receiver :

1) Press the PRG button on the BIX receiver. A “SIG” LED turns on. The receiver

is in a “learning mode”.

2) Press one of the channel buttons on your remote control. The LED flashes.

3) Repeat the operation for each remote control (100 max).

4) 10 second after the last transmission, the radio receiver goes back to the

“normal mode”.

Note:

If JR4=ON, all channels are memorized.

If JR4=OFF, only the channel we press (CH button) can be memorized.

How to erase all registered remote controls:

Press the PRG button on the radio receiver. Hold for 3 seconds until the “SIG” LED

starts flashing.

If you wish to erase alle the remotes from radio receiver memory, repeat the action

one more time (Press the PRG button on the radio receiver. Hold for 3 seconds.).

If you only want to erase one remote control, press the previously memorized CH

button on the remote.

The quickly flashing SIG light indicates the operation was successful.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DITEC Télécommande

DITEC

DITEC BIX AG4 Manuel utilisateur

DITEC

DITEC Gol4C Manuel du propriétaire

DITEC

DITEC BIXLR4 Guide rapide

DITEC

DITEC Bixa G4 Manuel du propriétaire

DITEC

DITEC BIXLR22-GOL Manuel utilisateur

DITEC

DITEC BIX L Series Manuel d'utilisation et d'entretien

DITEC

DITEC GOL4-C Manuel du propriétaire

DITEC

DITEC BIX L Series Manuel d'utilisation et d'entretien

DITEC

DITEC BIXLR22-GOL Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation