Dish Network WALLY Manuel

SET UP YOUR

WALLY

STEP 1: Unpair Your Remote

If you are unable to turn on your original receiver, go to step 2.

APress the SYSTEM INFO buon

on the front panel of your original

receiver.

BLocate your remote from the

list on the right-hand side of the

screen. Then, use your remote

control to highlight the “Unpair”

opon and press the SELECT

buon.

QUICK TIP

You will not be able to use your

remote with your replacement

receiver unl you unpair it from

your original receiver.

STEP 2: Label and Disconnect Your Cables

ALocate the cable connected to the

“Satellite In” port and aach the

blue label to it. Then, unscrew this

cable from your Wally. Do not

unscrew it from the wall.

BDetermine the cable you are using

to receive audio/visual signal and

aach the correct label to it. Then,

unplug it from the receiver. Do not

unplug it from your TV.

• Orange label - RCA cable

• Black label - HDMI cable

STEP 2: Label and Disconnect Your Cables (Cont.)

CLocate the cable connected to the

“Ethernet” port, and aach the

yellow label to it. Then, unplug

it from the receiver. Do not

disconnect it from the wall. (You

may not have this cable.)

DDisconnect the power cord from

the original receiver and the wall.

A new power cord was shipped

with your replacement Wally.

STEP 3: Connect the Cables to Your Replacement Receiver

AConnect the Satellite In cable

to the “Satellite In” port on your

replacement Wally.

BConnect the RCA cables or the

HDMI cable to the corresponding

ports on your replacement Wally.

STEP 3: Connect the Cables (Cont.)

CConnect the Ethernet cable

to the “Ethernet” port on your

replacement Wally. (You may not

have this cable.)

DConnect the power cord that

came with your replacement Wally

to the “Power” port on the new

Wally.

STEP 4: Power Your Equipment

APlug the power cord from your

replacement Wally into a power

outlet, and ensure that your TV is

sll plugged in. Turn your TV on.

BMake sure that the Smart Card is

secured rmly in the slot on the

side of your replacement Wally.

STEP 4: Power Your Equipment (Cont.)

CTurn on your TV and you will see

a loading screen, which could last

for several minutes.

DWhen the Install Wizard screen

appears, go to step 5.

QUICK TIP If you do not see the loading screen,

press the “Source/Input” buon located

on your TV unl this screen appears.

Starng Up...

STEP 5: Pair Your Remote to Your Wally

APress the SAT buon on your

remote control to pair it to

your Wally. All of your previous

receiver’s recording mers and

other sengs will be restored

automacally.

BOnce your remote is paired, the

Install Wizard will proceed to the

next step automacally.

QUICK TIP

To avoid pairing your remote with mulple

receivers, ensure that you do not have any other

receivers in your home that are on the “Pair Remote

Control” step or in the “Diagnoscs” screen. 9

STEP 6: Set Up Text to Speech

AIf you would like to have a digital

voice read the text on screen, use

your remote control to highlight

“Connue with Text to Speech.”

Then, press SELECT.

BIf you do not want a digital voice

to read the text on screen, use

your remote control to highlight

“Next,” and press SELECT.

QUICK TIP If you do not select either opon,

the Install Wizard will automacally

advance aer 30 seconds.

Autres manuels pour WALLY

Table des matières

Autres manuels Dish Network Récepteur TV

Dish Network

Dish Network Wireless Joey Manuel utilisateur

Dish Network

Dish Network Interactive TV Manuel utilisateur

Dish Network

Dish Network Wireless Joey Manuel utilisateur

Dish Network

Dish Network WALLY Manuel utilisateur

Dish Network

Dish Network Wireless Joey Manuel utilisateur

Dish Network

Dish Network Dish ViP722K Manuel utilisateur

Dish Network

Dish Network ViP 211k Manuel utilisateur

Manuels Récepteur TV populaires d'autres marques

NEC

NEC PX-TUAN-01 Manuel utilisateur

Edision

Edision Piccollino Manuel utilisateur

Matsui

Matsui DTR1 Manuel utilisateur

Dyon

Dyon Raptor Manuel utilisateur

Strong

Strong SRT 2401 Mode d'emploi

TerraTec

TerraTec CINERGY DT USB XS DIVERSITY Manuel d'instructions

Haier

Haier 34F9K Manuel utilisateur

TechniSat

TechniSat DigiCom 1 Manuel utilisateur

Haier

Haier LT19A1 Manuel utilisateur

Triax

Triax CR 317 Manuel utilisateur

DirecTV

DirecTV D10-300 Manuel utilisateur

Motorola

Motorola VIP2502W Manuel utilisateur

ActionTec

ActionTec WirelessTV Manuel utilisateur

Motorola

Motorola VIP1200 Series Manuel utilisateur

Xoro

Xoro HRT 1300 Manuel utilisateur

Motorola

Motorola DH6200 Manuel utilisateur

Manhattan

Manhattan Plaza DS-100 Manuel utilisateur

Micro Prose

Micro Prose MPI-500 Manuel utilisateur