DIRTY HANDS 107555 Manuel utilisateur

14”22” ADJUSTABLE FRONT TINE TILLER

is safety alert symbol identies important safety messages in

this manual. Failure to follow this important safety information

may result in serious injury or death.

MODEL # 107555

Operation Manual

Part 108749 Rev B

1100 W 120th Ave, Suite 600

Westminster, CO 80234 • 720-287-5182

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.dirtyhandtools.com

Dirty Hand Tools® is a brand of

Table of Contents

Important Safety Information

Intended Use ..............................................................................4

Personal Protective Equipment ..................................................4

General Safety ............................................................................5

Safety Decals ..............................................................................6

Unpacking and Assembly Instructions

Unpacking ...................................................................................7

Overview of Components.............................................................8

Tine Assembly...............................................................................9

Handlebar Assembly...................................................................10

Installing the Wheels..................................................................11

Safety Shield Assembly ...............................................................12

Operating Precautions................................................................13

Operating Instructions

Preparation for Operation .........................................................14

Fill Engine with Oil ..................................................................14

Pre-Start Inspection ..................................................................14

Adjusting the Depth Regulator.................................................14

Start-Up ....................................................................................15

Cold Starts ................................................................................15

Restarting A Warm Engine.......................................................15

Idle Speed..................................................................................15

Operating Speed........................................................................15

Shutting Down..........................................................................15

Tilling........................................................................................16

Clutch Lever .............................................................................16

Tilling Tips................................................................................16

Maintenance

Lubrication................................................................................17

Transmission Grease..................................................................17

Cleaning the Tine Axle Shaft....................................................17

Engine Maintenance .................................................................17

Storage.........................................................................................18

Troubleshooting..........................................................................19

Warranty & Specications .........................................Back Cover

Important Safety Information

WARNING: Read and thoroughly understand all instructions

and safety information before assembling or operating this tiller.

Failure to do so may cause serious injury or death. Do not allow

anyone to operate this tiller who has not read this manual. As

with all power equipment, a tiller can be dangerous if assembled

or used improperly. Do not operate this tiller if you have doubts or

questions concerning safe operation.

Call our customer service department at 720-287-5182,

1-877-487-8275, or visit www.dirtyhandtools.com if you have any

questions or concerns about the safe operation of this equipment.

Intended Use

Do Not Use the tiller for any purpose other than tilling garden soil

for which it was designed. Any other use is unauthorized and may

result in serious injury or death.

Personal Protective Equipment

When operating this tiller it is essential that you wear safety gear

including goggles or safety glasses, steel toed shoes and tight ﬁtting

gloves (no loose cuﬀs or draw strings). Always wear ear plugs or

sound deafening headphones to protect against hearing loss when

operating this tiller. Always wear sturdy footwear. Never wear

sandals, sneakers or open shoes, and never operate the tiller with

bare feet. Do not wear loose clothing that might get caught in

moving parts.

YOUR TILLER IS EQUIPPED WITH A CLUTCH

LEVER THAT AUTOMATICALLY STOP THE TINES

WHEN RELEASED

Learn how the clutch levers operate and

how to control the tiller at all times.

Read the entire Operation Manual before using this equipment!

WARNING

DANGER

CAUTION

Important Safety Information

General Safety

Failure to follow warnings, cautions, assembly and operation

instructions in the Operation Manual may result in serious injury

or death.

READ THE OPERATION MANUAL BEFORE

OPERATION.

• Do not permit children to operate this equipment at any time.

•Do not permit others that have not read and understood the

complete Operation Manual to operate this equipment.

• Keep all people and pets a minimum of 10 feet away from the

work area when operating this tiller.

• Do not operate the tiller when under the inﬂuence of alcohol,

drugs or medication.

• Do not allow a person who is tired or otherwise impaired or not

completely alert to operate the tiller.

CAREFULLY INSPECT THE AREA TO BE TILLED AND

REMOVE ALL FOREIGN OBJECTS.

Do not till above underground water lines, gas lines, electric cables,

or pipes. Do not operate the tiller in soil with large rocks and

foreign objects which can damage the equipment.

• Leave clutch lever undepressed (neutral) position before starting

the engine.

• Handle fuel with care; it is highly ﬂammable. Use an approved

fuel container. Never add fuel to a running engine or hot engine.

• Fill fuel tank outdoors with extreme care. Never ll fuel tank

indoors.

• Replace gasoline cap securely and clean up spilled fuel before

restarting.

• Never attempt to make any adjustments while the engine is

running.

DANGER

Important Safety Information

Safety Decals

Safety labels on the tiller are to remind you of important

information while you are operating the unit. Make sure

all safety warning decals are attached and in readable

condition. Replace missing or defaced decals. Contact

Dirty Hand Tools at 1-877-487-8275 for replacement

decals.

AVOID INJURY

FROM

ROTATING

TINES!

Keep hands, feet

and clothing away!

• Tines rotate when the

safety latch is flipped up

and the drive control

lever is depressed

towards the handle bar.

• To stop tines from

rotating release the

drive control lever.

The safety latch

automatically snaps

into locked position.

• Stop the engine, wait

for tines to stop rotating

and disconnect spark

plug before removing

debris or maintenance.

DANGER

101573

AVOID INJURY

• Know the function and

location of all controls.

• Never allow children to

operate the tiller.

• Check area to be tilled

and remove rocks or

obstacles.

• Check for underground

utilities before using.

WARNING

Read the

Operator’s

Manual

Before

Operating

Wear

Safety

Goggles or

Eyewear

Wear

Boots or

Protective

Footwear

Wear

Protective

Noise

Reduction

Gear

Wear

Gloves and

Protective

Clothing

101846

101726

DO NOT START ENGINE UNLESS

THE BELT COVER IS ATTACHED

TO THE TILLER.

KEEP HANDS, FEET AND CLOTHING AWAY

FROM MOVING BELTS AND PULLEYS.

FAILURE TO COMPLY COULD RESULT

IN SERIOUS INJURY.

SEE OWNER’S MANUAL FOR COMPLETE

OPERATING AND SAFETY INSTRUCTIONS.

101028

Unpacking and Assembly

Your tiller will require some assembly. e following instructions will

help you unpack your tiller, assemble and adjust the depth regulator

lever, cable tension and handlebar height. You will need a wrench,

small adjustable crescent wrench and a starbit driver to complete the

assembly.

Unpacking

Open top of carton and remove the tiller components.

Tiller Components

Upper Handlebar Left

Upper Handlebar Right

Handlebar Support Bracket

Handlebar Bridge

Depth Regulator

Safety Shields

Tine Blades (4)

Hardware Kit

DO NOT ADD ENGINE OIL TO THE

TRANSMISSION GEAR CASE

e tiller transmission is lled at the factory.

DO NOT ATTEMPT TO START ENGINE

BEFORE ADDING OIL TO ENGINE

e engine is shipped from the factory without oil. You must add

engine oil before starting the engine. Use only the recommended

weight of oil for a 4-cycle engine (See Engine Operation Manual).

CAUTION

Overview of Components

CLUTCH LEVER

HANDLEBAR

ASSEMBLY

WHEEL

ASSEMBLY

AIR

CLEANER

COVER

THROTTLE /

CHOKE CONTROL

FUEL FILL

RECOIL

STARTER

OUTER TINE

ASSEMBLY

INNER TINE

ASSEMBLY

SAFETY SHIELD

(TINE GUARD)

OIL FILL /

DIPSTICK

MUFFLER

Tine Assembly

Mounting the Tine Blades

1. Mount the 4 tines assemblies. Note that all 4 blades are diﬀerent.

e sharp edge of the blade should face forward, in the operational

direction. Make sure the clevis pin is securely fastened with a lynch pin.

Slide the tines onto the tiller’s axle. Align the connection holes in the

axle to the tine assemblies then secure with lynch pin (see Figure 1).

Figure 1

ASSEMBLED

TINES SECURED

WITH LYNCH PINS

14” 18” 22”

Handlebar Assembly

Mounting the Handlebars

NOTE: e left and right handlebars are diﬀerent. Each has two holes

drilled in the bottom of the handlebar tube and two more drilled in the

middle.

1. Install the upper handlebar bracket to the square tubing of the frame

using two M8x40mm bolts and nyloc nuts and two 13mm wrenches

in the conﬁguration shown in Figure 2.

2. Position the right and left handlebars with the grips facing outwards.

Align the two lower holes in the frame and upper handlebar bracket.

Install the M10x25mm and M10x50mm bolts as shown in Figure 2

and hand tighten.

3. Mount the handlebar bridge using four M8x40mm bolts and nyloc

nuts to the middle holes in the handlebars using two 13mm wrenches.

4. Finish tightening the lower M10 bolts and nyloc nuts using two

17mm wrenches.

5. Use the supplied zip ties to secure the cable from the clutch handle to

the handlebars and tiller frame.

Figure 2

HANDLEBAR

BRIDGE

LEFT

HANDLEBAR

RIGHT

HANDLEBAR

M8 x 40mm

M10 x 25mm

M10 x 50mm

FRAME

LEFT

TINE GUARD

RIGHT

TINE GUARD

PLASTIC WINGED

NUTS

UPPER HANDLEBAR

BRACKET

M8 x 40mm

Table des matières

Manuels Taller populaires d'autres marques

MTD

MTD 410R Manuel utilisateur

Craftsman

Craftsman 247.29931 Manuel utilisateur

MTD

MTD FRT Series Manuel utilisateur

Craftsman

Craftsman 917.298353 Manuel utilisateur

Troy-Bilt

Troy-Bilt Colt FT Manuel utilisateur

Ryobi

Ryobi 510r Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

YAT

YAT YT5601-01 Manuel d'entretien

Craftsman

Craftsman 917.296010 Manuel utilisateur

Troy-Bilt

Troy-Bilt OEM-290-260 Manuel utilisateur

Scheppach

Scheppach MTP560 Instructions de montage

GARDEN WAY

GARDEN WAY 12194 Manuel utilisateur

Classen

Classen STAND-AER SA-25 Instructions d'installation et d'entretien

Craftsman

Craftsman 850 Series Manuel utilisateur

DR PILOT 2 Guide de démarrage rapide

Altrad

Altrad ATIKA BH 1400 N Mode d’emploi

WIL-RICH

WIL-RICH 2500 Manuel utilisateur

Viking

Viking HB 685 Manuel utilisateur