Directed 3305 Manuel utilisateur
3305 & 3105
Installation Guide
This product is intended for installation by a professional installer
only! Any attempt to install this product by any person other than
a trained professional may result in severe damage to a vehicle’s
electrical system and components.
N3X05 2019-03
iii
© 2019 Directed. All rights reserved.
XKLOADER3, Code Hopping™, DEI®, Doubleguard®, ESP™,
FailSafe®, Ghost Switch™, Learn Routine™, Nuisance Prevention®
Circuitry, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stinger®,
Valet®, VRS®, and Warn Away® are all Trademarks or Registered
Trademarks of Directed.
iv © 2019 Directed. All rights reserved.
Important information
Government regulations
Read the Government regulations section of this manual
prior to operating this system.
Warning! Failure to heed this information can result in
injury, damage or the illegal use of the system beyond its
intended purpose.
Contents
Important information ....................................................................................... iv
Government regulations............................................................................ iv
Wiring Diagram ...............................................................................................2
Wiring Connections ..........................................................................................3
Main (Primary) Harness, White 12-pin connector..........................................3
Door Lock Harness, 3-pin connector ..........................................................3
Primary Harness - 12-pin connector.....................................................................4
Door Lock Harness, White 3-pin connector...........................................................9
Control Center..................................................................................................9
XKLOADER3/Directed SmartStart, Black 3-pin connector .....................................10
Mounting the Control Center ............................................................................11
Onboard Dual Stage Shock Sensor ...................................................................12
Optional Sensor Harness, White 4-pin connector ...............................................12
Parking Light Jumper........................................................................................13
Bypassing Sensor Inputs...................................................................................14
System Features Learn Routine .........................................................................14
Feature Menus ...............................................................................................17
Menu 1 .................................................................................................17
Menu 2 .................................................................................................18
Feature Descriptions ........................................................................................19
Menu 1 ................................................................................................19
Menu 2 .................................................................................................21
Pairing a Remote Control .................................................................................25
Remote Control Configurations .........................................................................28
Standard configuration............................................................................28
3-button configuration (optional, not included)............................................28
Diagnostics ....................................................................................................29
Arm/disarm diagnostics ..........................................................................29
Table of zones........................................................................................30
Multi-Level Security Arming...............................................................................31
VRS (Vehicle Recovery System)..........................................................................32
NPC (Nuisance Prevention Circuitry) .................................................................32
Rapid Resume Logic ........................................................................................32
Troubleshooting: Security .................................................................................33
Government Regulations ..................................................................................35
2© 2019 Directed. All rights reserved.
Wiring Diagram
Output
Output
may require
a relay
may require a relay
XKLOADER 3/
SmartStart
D2D
(for interface module)
Control Button
Control Center
LED
XKL
3
Sensor adjustment
detail
Light Flash
Jumper
(-)
(+)
3
© 2019 Directed. All rights reserved.
Wiring Connections
Main (Primary) Harness, White 12-pin connector
1 ORANGE (-) 500mA GWA (Ground When Armed) OUTPUT
2 WHITE (+/-) SELECTABLE PARKING LIGHT OUTPUT
3 WHITE/BLUE (-) 200mA CHANNEL 3 PROGRAMMABLE OUTPUT
4 BLACK/WHITE (-) 200mA DOMELIGHT SUPERVISION OUTPUT
5 GREEN (-) DOOR TRIGGER INPUT, ZONE 3
6 BLUE (-) INSTANT TRIGGER INPUT, ZONE 1
7 VIOLET (+) DOOR TRIGGER INPUT, ZONE 3
8 BLACK (-) CHASSIS GROUND INPUT
9 YELLOW (+) SWITCHED IGNITION INPUT, ZONE 5
10 BROWN (+) SIREN OUTPUT
11 RED (+) CONSTANT POWER INPUT
12 RED/WHITE (-) 200mA CHANNEL 2 OUTPUT
Important: NEVER connect 200mA/500mA low current outputs directly to a
motor or high current device WITHOUT a relay.
Door Lock Harness, 3-pin connector
1 LIGHT BLUE 200 mA (-) UNLOCK, 200 mA (+) LOCK OUTPUT
2 EMPTY NOT USED
3 GREEN 200 mA (-) LOCK, 200 mA (+) UNLOCK OUTPUT
Important: Never use this wire to drive anything but a relay or a low-current
input! The transistorized output can only supply 200 mA of current. Con-
necting directly to a solenoid, motor, or other high-current device will cause
it to fail.
4© 2019 Directed. All rights reserved.
Primary Harness - 12-pin connector
This guide describes in detail the connection of each wire. Also includ-
ed are possible applications of each wire. This system was designed
with the ultimate in flexibility and security in mind. Many of the wires
have more than one possible function. Please read carefully to ensure
a thorough understanding of this unit.
1ORANGE (-) 500 mA GWA (Ground When Armed) OUTPUT
This wire supplies a (-) ground as long as the system is armed. This
output ceases as soon as the system is disarmed. The Orange wire is
pre-wired to control the 8618 starter disable relay. It can supply up to
500 mA of current.
Note: If using the this Orange wire to activate an add-on accessory
such as window automation, or voice module a 1-amp diode must be
installed to ensure proper operation. Insert the diode as shown in the
following diagram.
Important: Never interrupt any wire other than the starter wire.
5
© 2019 Directed. All rights reserved.
2WHITE (+/- ) SELECTABLE PARKING LIGHT OUTPUT
As shipped, this White wire should be connected to the (+) parking
light wire. If the parking light polarity jumper is moved to the (-) position
(see the Parking light jumper section of this installation guide), this wire
supplies a (-) 200 mA output.
For parking light systems that draw 10 amps or more, the jumper must
be switched to a (-) parking light output (see the Parking light jumper
section of this guide). P/N 8617 or a standard automotive SPDT relay
must be used for the parking light output.
Important: DO NOT connect the white parking light output to a negative
vehicle parking light wire before changing the programming jumper to the
negative polarity position or damage to vehicle light circuit may occur.
3WHITE/
BLUE
200mA CHANNEL 3 PROGRAMMABLE OUTPUT
This wire provides a (-) 200 mA output, whenever the remote control
button(s) controlling channel 3 output is pressed. This wire can be pro-
grammed to provide different types of outputs (see "System features
learn routine" on page 14 of this guide).
6© 2019 Directed. All rights reserved.
Important: Never use this wire to drive anything but a relay or a low-current
input! This transistorized output can only supply 200mA, and connecting di-
rectly to a solenoid, motor, or other high-current device will cause the module
to fail.
4BLACK/WHITE 200mA (-) DOMELIGHT SUPERVISION
OUTPUT
Connect this wire to an optional domelight supervision relay as shown
in the following diagram:
WIRE
This wire supplies a (-) 200 mA output for 30 seconds when the system
is disarmed, and when the ignition is turned off (programmable On/
Off). It will pulse continuously during the alarm trigger duration.
Important: This output is only intended to drive a relay. It cannot be con-
nected directly to the domelight circuit, as the output cannot support the
current draw of one or more bulbs.
5GREEN (-) DOOR TRIGGER INPUT
Most vehicles use negative door trigger circuits. Connect the Green
wire to a wire showing ground when any door is opened. When con-
Ce manuel convient aux modèles suivants
1
Table des matières
