DINSpace SNAP Series Manuel utilisateur

SNAP®Compact Fiber Patch Panel

Installation Instructions

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Table of Contents

System Description................................................................................................3

Package Contents .................................................................................................3

Warranty and Repair Information ..............................................................................3

Mounting the SNAP Patch Panel - Rear DIN-Rail Option....................................................4

Mounting the SNAP Patch Panel - Side DIN-Rail Option....................................................4

Mounting the SNAP Patch Panel - Rear Surface Mount Option...........................................5

Connecting Field Fiber Optic Cable - Patch Option........................................................5

Connecting Field Fiber Optic Cable - Fusion Splice Option...............................................6

Appendix A – Dimensional drawings.............................................................................8

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

System Description

Compact DIN-Rail or surface mount ber optic patch panel. The device’s compact size allows minimum

space requirements within control cabinetry. While often used as a patch panel, the device also includes

a splice tray to allow fusion splicing of eld cabling (pigtails sold separately and are not included in the

SNAP product packaging). The SNAP Patch Panel features a sliding faceplate with capture mechanism

to allow the patch panel to be kept open “hands-free” while allowing the user to connect or disconnect

ber on the back of the faceplate.

Package Contents

Your SNAP Compact Fiber Optic Patch Panel packaging should contain the following:

1. SNAP Patch Panel with 6ea. ber optic adapters, two cable glands (Maximum eld cable diameter

12mm) and two dust plugs pre-installed.

2. Recloseable bag containing:

a. Zip-ties

b. Hex wrench

c. Numbered stickers

Note: If you observe any product damage, or missing parts upon unpacking of the product, please

contact DINSpace immediately at [email protected] or by calling 214-613-0349.

Warranty and Repair Information

DINSpace guarantees all of its standard products to be of rst-class construction and provides a lifetime

warranty against any defects in material and workmanship. The warranty does not apply to damage

caused by abnormal or unreasonable use of any of the products (including repairs or alterations other

than by DINSpace technical support). This warranty is in place of all other warranties, including

warranty of tness for a particular purpose and warranty of merchantability and excludes any liability

for incidental or consequential damages.

Repairs

If your DINSpace product has a manufacturer’s defect covered by our warranty, we will either repair

or replace it, at our option, without charge. Please contact DINSpace customer support to describe

the issue, and if a return is deemed necessary to resolve the issue, a Return Merchandise Authorization

(RMA) number will be issued. No returns will be accepted without an RMA number. Send to the address

below. Include your name, address, phone number and the RMA number with your return. A product

not covered by the warranty can be repaired. Note that repair costs and handling charges may apply.

If so, you will be notied prior to any service.

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Mounting the SNAP Patch Panel – Rear DIN-Rail Option

The SNAP Patch panel is shipped with the DIN-Rail clip pre-installed for a rear

DIN-Rail mount. To mount the patch panel to 35mm DIN-Rail:

1. Position the rear panel of the patch panel directly in front of the DIN-Rail,

making sure the bottom of the patch panel DIN-Rail clip hooks under the

bottom of the DIN-Rail, as shown in Figure 1.

2. Gently pull the bottom of the patch panel upward to compress the spring

and allow the top rail to be engaged.

3. Rotate the patch panel up toward the DIN-Rail until the top of the patch

panel DIN-Rail clip is over the DIN-Rail.

4. Relieve the upward pressure on the patch panel, and the captured spring

will extend, holding the patch panel tightly to the DIN-Rail as seen in

Figure 2.

Mounting the SNAP Patch Panel - Side DIN-Rail Option

The SNAP Patch panel is shipped with the DIN-Rail clip pre-installed for a rear DIN-Rail mount. In order

to side mount the SNAP Patch Panel:

1. Using a 2.5mm Hex Wrench, remove the two hex-nuts securing the

DIN-Rail clip on the rear of the SNAP Patch Panel as seen in Figure 3.

2. Secure the DIN-Rail Clip (spring clasp on bottom) to the two pre-

drilled holes on the side of the SNAP Patch Panel, using the same

two hex-nuts and DIN-Rail clip as seen in Figure 4.

3. Position the side panel of the patch panel directly in front of the

DIN-Rail, making sure the bottom of the patch panel DIN-Rail clip

hooks under the bottom of the DIN-Rail, as shown in Figure 5.

4. Gently pull the bottom of the patch panel upward to compress the

spring and allow the top rail to be engaged.

5. Rotate the patch panel up toward the DIN-Rail until the top of the

patch panel DIN-Rail clip is over the DIN-Rail.

6. Relieve the upward pressure on the patch panel, and the captured

spring will extend, holding the patch panel tightly to the DIN-Rail as

seen in Figure 6.

Figure 3

Figure 4

Figure 1

Figure 2

Figure 5 Figure 6

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Mounting the SNAP Patch Panel - Rear Surface Mount Option

The SNAP Patch panel is shipped with the DIN-Rail clip pre-installed for a rear

DIN-Rail mount. In order to surface mount the Patch Panel:

1. Using a 2.5mm Hex Wrench, remove the two hex-nuts securing the DIN-Rail

clip on the rear of the SNAP Patch Panel as seen in Figure 7 and Figure 8.

2. Unfasten the faceplate from the SNAP Patch Panel using the hex wrench

provided in the packaging.

3. Remove the faceplate from the SNAP Patch Panel, as seen in Figure 9, to

allow access to the rear of the Patch Panel.

4. Use surface mount hardware (not included) to mount the SNAP Patch Panel

to the surface using the four pre-drilled mounting holes in the rear of the

SNAP Patch Panel.

5. Replace the faceplate onto the SNAP Patch Panel.

Connecting Field Fiber Optic Cable - Patch Option

After mounting the SNAP Patch Panel to the DIN-Rail or surface as described above:

1. Loosen cable gland (Maximum eld cable diameter 12mm) to allow eld distribution

cable to enter the SNAP Patch Panel. Loosen the cable gland(s) that you will be

using, and pass the eld ber optic cable through the gland as seen in Figure 10.

2. Terminate the appropriate termination hardware to the eld ber optic strands

taking care to match the termination hardware to the interior adapter style of the

SNAP faceplate. See table below:

3. After securing the eld connectors to the interior adapter interfaces of the SNAP faceplate, close

the faceplate and secure it with the two hex nuts provided.

4. Tighten the cable gland to create a seal against the eld ber cable.

Figure 7

Figure 8

Figure 9

SNAP Patch Panel Field Fiber Termination required

SNAP-12ST-MM Multimode ST adapter

SNAP-12ST-SM Singlemode ST adapter

SNAP-12SC-ST-MM Multimode SC adapter

SNAP-12SC-ST-SM Singlemode SC adapter

SNAP-12SC-MM Multimode SC adapter

SNAP-12SC-SM Singlemode SC adapter

SNAP-24-LC-MM Multimode LC adapter

SNAP-24-LC-SM Singlemode LC adapter

Figure 10

Note: If you are gluing the eld terminators onto the eld cable, make sure you al-

low sufcient time for the adhesive to dry before attempting to secure the connec-

tor into the interior adapters of the SNAP faceplate. DINSpace cannot be responsible

for replacing adapter hardware if damaged due to termination errors.

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Connecting Field Fiber Optic cable - Fusion Splice Option

To terminate eld ber optic cable using fusion splicing, you must rst ensure that you have appropriate

ber optic pigtails (sold separately or provided by Customer) to fuse to the Field Fiber, and you are

using SNAP R30086 splice protectors:

1. Loosen the SNAP Enclosure cable gland(s) and pass eld

ber through to enter the SNAP enclosure Note: In cases

where fusion splicing is used, it may be preferable to

remove the faceplate hinge (Figure 11) mechanism to

ensure that no snagging occurs.

2. Strip back the ber optic pigtail to the 250μ cladding

layer.

3. Strip back the eld ber to the 900μ sheathing layer.

4. Perform the fusion splice Note: Keep in mind that

cladding to cladding distance of the splice must be less

than the length of the SNAP Splice protector (DINSpace

Part Number: SNAP R30086) in order to protect the splice

properly.

5. Insert fused cables into ant mechanical enclosure with

pigtail and eld ber sheathes inside the Fiber Splice

Protector on either end, as seen in Figure 12.

SNAP Patch Panel Pigtail Required Pigtail Part Number

SNAP-12ST-MM Multimode pigtail with ST adapter - 900μ sheath SNAP-Pigtail-01ST-MM

SNAP-12ST-SM Singlemode pigtail with ST adapter - 900μ sheath SNAP-Pigtail-01ST-SM

SNAP-12SC-ST-MM Multimode pigtail with SC adapter - 900μ sheath SNAP-Pigtail-01SC-MM

SNAP-12SC-ST-SM Singlemode pigtail with SC adapter - 900μ sheath SNAP-Pigtail-01SC-SM

SNAP-12SC-MM Multimode pigtail with SC adapter - 900μ sheath SNAP-Pigtail-01SC-MM

SNAP-12SC-SM Singlemode pigtail with SC adapter - 900μ sheath SNAP-Pigtail-01SC-SM

SNAP-24-LC-MM Multimode pigtail with LC adapter - 900μ sheath SNAP-Pigtail-01LC-MM

SNAP-24-LC-SM Singlemode pigtail with LC adapter - 900μ sheath SNAP-Pigtail-01LC-SM

Figure 11

Figure 12

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

6. Insert closed Fiber Splice Protector into the splice holder tray as shown in Figure 13.

7. Wrap excess pigtail inside the provided spooling cage. Use provided Zip ties to secure excess

pigtail cables into spooling cage Note: Some users prefer Velcro straps for looser binding).

8. Close SNAP faceplate while gently taking up slack in the eld ber cable before tightening the

cable gland against the eld cable to create a seal.

Figure 13

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Appendix A – Dimensional drawings

Front

View

Rear

View

Side

View

Width - 2.75” (69.9 mm) Height - 6.25” (158.8 mm)

Depth - with DIN-Rail mount 5.125” (130.2 mm)

without DIN-Rail mount 4.875” (123.8 mm)

4”

(101.6 mm)

1.125”

(28.6 mm)

1.125”

(28.6 mm)

1.25”

(31.8 mm)

1.5”

(38.1 mm)

1.25”

(31.8 mm)

0.577”

(14.7 mm)

Hole Diameter

0.17”

(4.32 mm)

Surface

Mount

Phone: 214-613-0349 | Fax: 866-622-4068 | Web: www.dinspace.com

Ce manuel convient aux modèles suivants

Table des matières

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques