Dinan Dinantronics X Manuel utilisateur
PLEASE
READ BEFORE
STARTING
INSTALLATION!
User Manual
Performance upgrade
+APP-CONTROL
27: ; N20
1 Scope of Delivery .....................................................................................................................................................................................................A
2 Overview of the performance upgrade .............................................................................................................................................................. B
3 Installation ................................................................................................................................................................................................................ C
4 Fine tuning ................................................................................................................................................................................................................ D
5 Trouble Shooting.......................................................................................................................................................................................................E
Contents
Overview and explanation of symbols
Warnings and important information – please read!
General information on installation and use
Tips to assist installation and use
(1) Picture may differ from delivered product.
A
B
C
Performance Upgrade
calibrated specifically for your
vehicle
Wiring harness
automobile-grade, compatible
with your vehicle (1)
Cable ties
2 x long cable ties
3 x short cable ties
Deactivation plug
D
User Manual
E
A
1 Scope of Delivery
A
C
E
F
B
A
B
C
Digital User Interface for controlling
the .
+/- buttons for changing the mapping
(see Fine tuning)
Power ON light; lights only when the
vehicle ignition is on and power is
being supplied to the RaceChip.
Display showing mapping selected
(see Fine tuning).
D
lot for
E
FCI plug for connecting to the vehicle’s
wiring.
F
B
A
B
C
D
F
E
E
2 Overview of the performance upgrade
C
3 Installation
Step 1 of 8
1
2
– Preparation
efore nang e nng mode peae a for or engne o coo don
ere ere a r of anng rn
Open your vehicle’s bonnet, and close and lock the doors.
Wait about 10 minutes before starting Step 2, as all current consumers must have
switched themselves off.
Generally speaking, you do not require special tools to perform the installation. If you
need a tool, we will tell you when you get to the relevant step in these instructions. You
will probably find wire cutters useful for clipping off the loose ends of cable ties.
• For cars with “Keyless Go”: after locking the car, place the key out of signal range
(about 10 m from the car).
• If an alarm system is fitted disable the alarm before starting installation.
• Some cars will not lock completely if the bonnet is open and electrical consumers
are still active. If this is the case with your car, push the bonnet catch over manually,
lock the car again and wait ca. minutes. hen you have finished the installation,
do not forget to release the catch again by pulling the bonnet release lever.
•f you have any uestions or difficulties during the installation, please refer to
for hints and tips.
C
3 Installation
•Remove the engine cover and place it next to the car. You may have to jiggle the cover
slightly to release it from the holding clips.
– Removing the engine coverStep 2 of 8
C
3 Installation
1
A
Step 3 of 8 – Connection to turbo boost pressure sensor
•First locate the turbo boost pressure sensor connection in your engine bay.
Turbo boost pressure sensor
Turbo boost
pressure sensor
Setup illustration
Cable with disconnected
stock plug
Cable from the
tuning module.
Turbo boost pressure sensor
C
3 Installation
•Disconnect the plug from the turbo boost pressure sensor
f you experience difficulties disconnecting the turbo boost pressure sensor, see
Detaching the Connector Correctly (separate document) for assistance.
Make sure that the plug’s locking clip engages again. You should hear a sharp CLICK.
• Now connect the end of the wiring harness marked “A” to the
disconnectedconnector and the other end to the sensor.
2
3
C
3 Installation
1
B
Step 4 of 8 – Connection to manifold absolute pressure sensor
Manifold absolute
pressure connection
Manifold absolute
pressure connection
Manifold absolute
pressure connection
•Once the connection to the turbo boost pressure is complete, it is time to make the
connection to the manifold absolute pressure sensor.
Setup illustration
Cable with disconnected
stock plug
Cable from the
tuning module
C
3 Installation
Make sure that the plug’s locking clip engages again. You should hear a sharp CLICK.
• Now connect the end of the wiring harness marked “B” to the disconnected
connector and the other end to the sensor.
f you experience difficulties disconnecting the manifold absolute pressure sensor, see
Detaching the Connector Correctly (separate document) for assistance.
•Disconnect the plug from the manifold absolute pressure sensor.
2
3
Ce manuel convient aux modèles suivants
1
Table des matières
